CHL8225-03CRT

CHL8225-03CRT Datasheet

CHL8225/CHL8228

Part	Datasheet
CHL8225-03CRT	CHL8225-03CRT (pdf)

Related Parts	Information
CHL8225-02CRT	CHL8225-02CRT

PDF Datasheet Preview
CHL8225/CHL8228 DIGITAL MULTI-PHASE BUCK CONTROLLER • 5-phase & 8-phase dual output PWM Controller with phases flexibly assigned between Loops 1 & 2 • Dynamic voltage control by 2-bit parallel interface with Gamer Mode override and Vmax setting • Input Voltage Management for up to 3 Input Voltages • ICRITICAL Monitor and Phase Current Capture Mode • Phase Switching frequency from 200kHz to 1.2MHz • CHiL Efficiency Shaping Features including Variable Gate Drive, Dynamic Phase Control • Programmable 1-phase or 2-phase for Light Loads and Active Diode Emulation for Very Light Loads • CHiL Adaptive Transient Algorithm ATA minimizes output bulk capacitors and system cost • Designed for use with coupled inductors • Per-Loop Fault Protection OVP, UVP, OCP, OTP • I2C/SMBus/PMBus system interface for telemetry of Temperature, Voltage, Current & Power for both loops • Non-Volatile Memory NVM for custom configuration • Compatible with CHiL ATL and 3.3V tri-state Drivers • +3.3V supply voltage 0ºC to 85ºC ambient operation • Pb-Free, RoHS, 6x6 40pin & 8x8 56pin QFN packages parameters are easily defined using the CHiL Intuitive Power Designer IPD GUI and stored in on-chip NVM. The CHL8225/8 provides extensive OVP, UVP, OCP and OTP fault protection and includes thermistor based temperature sensing with VRHOT signal. The CHL8225/8 includes numerous features like register diagnostics for fast design cycles and platform differentiation, simplifying VRD design and enabling fastest time-to-market with its “set-and-forget” methodology. IRTN1 ISEN1 IRTN2 ISEN2 IRTN3 ISEN3 IRTN4 ISEN4 IRTN5 ISEN5 40 39 38 37 36 35 34 33 32 31 RCSP 1 RCSM 2 VCC 3 VSEN 4 VRTN 5 RRES 6 TSEN 7 V18A 8 VR_READY 9 VR_READY_L2 10 CHL8225 40 Pin 6x6 QFN Top View 41 GND 30 RCSP_L2 29 RCSM_L2 28 VCC 27 VSEN_L2 26 VRTN_L2 25 PWM5 24 PWM4 23 PWM3 22 PWM2 21 PWM1 11 12 13 14 15 16 17 18 19 20 VAR_GATE SMB_CLK SMB_DIO ENABLE ISEN3 VRHOT_ICRIT# VIDSEL0 VIDSEL1 VIDSEL_L2 ISEN1 VINSEN_AUX1 VINSEN The CHL8225/8 are dual-loop digital multi-phase buck controllers. The CHL8225 drives up to 5 phases and the CHL8228 drives up to 8 phases. They feature Input Voltage Management allowing up to 3 input voltages to be monitored to ensure adequate power is delivered to the load. Dynamic voltage control is provided by 4 registers which are programmed through I2C/SMBus/PMBus and then selected using a 2-bit parallel bus for fast access. The CHL8225/8 NVM saves pins and enables a small package size. The CHL8225/8 includes the CHiL Efficiency Shaping Technology to deliver exceptional efficiency at minimum cost across the entire load range. CHiL Variable Gate Drive optimizes the MOSFET gate drive voltage as a function of real-time load current. CHiL Dynamic Phase Control adds and drops phases based upon load current. The CHL8225/8 can be configured to enter 1-phase operation and active diode emulation mode based upon load current or by command. CHiL’s unique Adaptive Transient Algorithm ATA , based on proprietary non-linear digital PWM algorithms, minimizes output bulk capacitors. In addition, a coupled inductor mode, with phases added/dropped in pairs enables further improvement in transient response and form factor. The I2C/PMBus interface can communicate with up to 16 CHL8225/8 based VR loops. Device configuration and fault IRTN8 IRTN1 IRTN2 ISEN2 ORDERING INFORMATION CHL822 - T Tape & Reel Package type R QFN Operating Temperature C Commercial Standard Rxxa:nCgeonfiguration file R QFN Part 5 CHL8225 8 CHL8228 Package QFN Tape & Reel Qty 3000 Part Number CHL8225-00CRT1 CHL8225-xxCRT2 CHL8228-00CRT1 CHL8228-xxCRT2 Notes 1 For unprogrammed/default parts, use configuration file Unprogrammed parts will not start up until programmed in order to insure a safe power up. 2 -xx indicates a customer specific configuration file.

PDF Datasheet Preview

CHL8225/CHL8228

DIGITAL MULTI-PHASE BUCK CONTROLLER
• 5-phase & 8-phase dual output PWM Controller with phases flexibly assigned between Loops 1 & 2
• Dynamic voltage control by 2-bit parallel interface with Gamer Mode override and Vmax setting
• Input Voltage Management for up to 3 Input Voltages
• ICRITICAL Monitor and Phase Current Capture Mode
• Phase Switching frequency from 200kHz to 1.2MHz
• CHiL Efficiency Shaping Features including Variable

Gate Drive, Dynamic Phase Control
• Programmable 1-phase or 2-phase for Light Loads and

Active Diode Emulation for Very Light Loads
• CHiL Adaptive Transient Algorithm ATA minimizes output bulk capacitors and system cost
• Designed for use with coupled inductors
• Per-Loop Fault Protection OVP, UVP, OCP, OTP
• I2C/SMBus/PMBus system interface for telemetry of

Temperature, Voltage, Current & Power for both loops
• Non-Volatile Memory NVM for custom configuration
• Compatible with CHiL ATL and 3.3V tri-state Drivers
• +3.3V supply voltage 0ºC to 85ºC ambient operation
• Pb-Free, RoHS, 6x6 40pin & 8x8 56pin QFN packages
parameters are easily defined using the CHiL Intuitive Power Designer IPD GUI and stored in on-chip NVM.

The CHL8225/8 provides extensive OVP, UVP, OCP and OTP fault protection and includes thermistor based temperature sensing with VRHOT signal.

The CHL8225/8 includes numerous features like register diagnostics for fast design cycles and platform differentiation, simplifying VRD design and enabling fastest time-to-market with its “set-and-forget” methodology.

IRTN1 ISEN1 IRTN2 ISEN2 IRTN3 ISEN3 IRTN4 ISEN4 IRTN5 ISEN5
40 39 38 37 36 35 34 33 32 31

RCSP 1 RCSM 2

VCC 3 VSEN 4 VRTN 5 RRES 6 TSEN 7 V18A 8 VR_READY 9 VR_READY_L2 10

CHL8225 40 Pin 6x6 QFN

Top View
41 GND
30 RCSP_L2 29 RCSM_L2 28 VCC 27 VSEN_L2 26 VRTN_L2 25 PWM5 24 PWM4 23 PWM3 22 PWM2 21 PWM1
11 12 13 14 15 16 17 18 19 20

VAR_GATE

SMB_CLK

SMB_DIO

ENABLE

ISEN3 VRHOT_ICRIT#

VIDSEL0

VIDSEL1

VIDSEL_L2

ISEN1 VINSEN_AUX1

VINSEN

The CHL8225/8 are dual-loop digital multi-phase buck controllers. The CHL8225 drives up to 5 phases and the CHL8228 drives up to 8 phases. They feature Input Voltage Management allowing up to 3 input voltages to be monitored to ensure adequate power is delivered to the load. Dynamic voltage control is provided by 4 registers which are programmed through I2C/SMBus/PMBus and then selected using a 2-bit parallel bus for fast access.

The CHL8225/8 NVM saves pins and enables a small package size.

The CHL8225/8 includes the CHiL Efficiency Shaping Technology to deliver exceptional efficiency at minimum cost across the entire load range. CHiL Variable Gate Drive optimizes the MOSFET gate drive voltage as a function of real-time load current. CHiL Dynamic Phase Control adds and drops phases based upon load current. The CHL8225/8 can be configured to enter 1-phase operation and active diode emulation mode based upon load current or by command.

CHiL’s unique Adaptive Transient Algorithm ATA , based on proprietary non-linear digital PWM algorithms, minimizes output bulk capacitors. In addition, a coupled inductor mode, with phases added/dropped in pairs enables further improvement in transient response and form factor.

The I2C/PMBus interface can communicate with up to 16 CHL8225/8 based VR loops. Device configuration and fault

IRTN8

IRTN1

IRTN2

ISEN2
ORDERING INFORMATION

CHL822 -

T Tape & Reel

Package type R QFN

Operating Temperature C Commercial Standard

Rxxa:nCgeonfiguration file R QFN

Part 5 CHL8225 8 CHL8228

Package QFN

Tape & Reel Qty 3000

Part Number CHL8225-00CRT1 CHL8225-xxCRT2 CHL8228-00CRT1 CHL8228-xxCRT2

Notes 1 For unprogrammed/default parts, use configuration file

Unprogrammed parts will not start up until programmed in order to insure a safe power up. 2 -xx indicates a customer specific configuration file.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived CHL8225-03CRT Datasheet file may be downloaded here without warranties.

Datasheet ID: CHL8225-03CRT 637985