SX100AD4

SX100AD4 Datasheet

Datasheet -- SX100AD4

Part	Datasheet
SX100AD4	SX100AD4 (pdf)

PDF Datasheet Preview
Datasheet -- SX100AD4 SX100AD4 Pressure Sensors Measurement Type Absolute 0 psia to 100 psia, Unamplified, "D4" DIP Package - Straight Port Representative photograph, actual product appearance may vary. q Low Cost q High-Impedance Bridge q Absolute and Differential Gauge q Low Noise q Low Power Consumption for Battery Power Due to regional agency approval requirements, some products may not be available in your area. Please contact your regional Honeywell office regarding your product of choice. q Medical q Instrumentation q Barometric q Measurement q Pneumatic Controls q Battery Powered Equipment The SX Series pressure sensors provide the lowest cost components for measuring pressures up to 150 psi. These sensors are designed for use with non-corrosive, non-ionic media, such as air and dry gases. Convenient pressure ranges are available to measure differential, gauge, and absolute pressures from 0 psi to 1 psi SX01 up to 0 psi to 150 psi SX150 . The Absolute A devices have an internal vacuum reference and an output voltage proportional to absolute pressure. The differential D devices allow application of pressure to either side of the diaphragm and can be used for gauge or differential pressure measurements. This product is packaged in either the standard low cost chip carrier “button” package, a plastic ported “N” package, or a DIP package. 1 of 5 15/03/2005 01:39:14 Datasheet -- SX100AD4 All packages are designed for applications where the sensing element is integral to the OEM equipment. These packages can be oring sealed, epoxied, and/or clamped onto a pressure fitting. A closed-bridge four pin SIP configuration is provided for electrical connection to the “Button” or “N” Package. The DIP Package mounts on a PC board like a standard IC with through-hole pins. This extremely small size package enables the use of multiple sensors in applications with limited space. SX100AD4 Pressure Sensors Measurement Type Absolute 0 psia to 100 psia, Unamplified, "D4" DIP Package - Straight Port Product Specifications Measurement Type Absolute Signal Conditioning Unamplified Pressure Range 0 psia to 100 psia Maximum Overpressure 150 psia Supply Voltage 12 Vdc max. Compensated Output Calibration Response Time 100 µS Termination Port Style Straight Package Style D4 DIP Typical Sensitivity mV/V/psi Full Scale Span 100 mV min., 150 mV typ., 200 mV max. Zero Pressure Offset mV min., mV typ., mV max.

PDF Datasheet Preview

Datasheet -- SX100AD4

SX100AD4

Pressure Sensors Measurement Type Absolute 0 psia to 100 psia, Unamplified, "D4" DIP Package - Straight Port

Representative photograph, actual product appearance may vary.
q Low Cost q High-Impedance Bridge q Absolute and Differential Gauge q Low Noise q Low Power Consumption for Battery Power

Due to regional agency approval requirements, some products may not be available in your area. Please contact your regional Honeywell office regarding your product of choice.
q Medical q Instrumentation q Barometric q Measurement q Pneumatic Controls q Battery Powered Equipment

The SX Series pressure sensors provide the lowest cost components for measuring pressures up to 150 psi. These sensors are designed for use with non-corrosive, non-ionic media, such as air and dry gases. Convenient pressure ranges are available to measure differential, gauge, and absolute pressures from 0 psi to 1 psi SX01 up to 0 psi to 150 psi SX150 .

The Absolute A devices have an internal vacuum reference and an output voltage proportional to absolute pressure. The differential D devices allow application of pressure to either side of the diaphragm and can be used for gauge or differential pressure measurements.

This product is packaged in either the standard low cost chip carrier “button” package, a plastic ported “N” package, or a DIP package.
1 of 5 15/03/2005 01:39:14

Datasheet -- SX100AD4

All packages are designed for applications where the sensing element is integral to the OEM equipment. These packages can be oring sealed, epoxied, and/or clamped onto a pressure fitting. A closed-bridge four pin SIP configuration is provided for electrical connection to the “Button” or “N” Package. The DIP Package mounts on a PC board like a standard IC with through-hole pins. This extremely small size package enables the use of multiple sensors in applications with limited space.

SX100AD4

Pressure Sensors Measurement Type Absolute 0 psia to 100 psia, Unamplified, "D4" DIP Package - Straight Port

Product Specifications

Measurement Type

Absolute

Signal Conditioning

Unamplified

Pressure Range
0 psia to 100 psia

Maximum Overpressure
150 psia

Supply Voltage
12 Vdc max.

Compensated

Output Calibration

Response Time
100 µS

Termination

Port Style

Straight

Package Style

D4 DIP

Typical Sensitivity
mV/V/psi

Full Scale Span
100 mV min., 150 mV typ., 200 mV max.

Zero Pressure Offset
mV min., mV typ., mV max.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived SX100AD4 Datasheet file may be downloaded here without warranties.

Datasheet ID: SX100AD4 636553