HOD1340-312/GBA

HOD1340-312/GBA Datasheet

HOD1340-312/GBA HOD2135-142/GBA

Part	Datasheet
HOD1340-312/GBA	HOD1340-312/GBA (pdf)

Related Parts	Information
HOD2135-142/GBA	HOD2135-142/GBA

PDF Datasheet Preview
Fibre Optic Components Single Fibre Duplex Modules • Full duplex over single fibre • DC to 25MHz link bandwidth • 2km+ link budget • 40dB isolation • Close mount ST housing • Other options available HOD1340-312/GBA HOD2135-142/GBA The Honeywell HOD-XXXX series of dual wavelength 'Fibre Duplexers' allow communication over a single optical fibre link. Applications include full duplex data transmission, multiplexing two signals to a single fibre, LED coupled power measurements and reflected power measurements, depending upon the configuration of the duplexer. The HOD2135-142/GBA comprises a 1300nm LED and an 850nm PIN Diode and its corresponding part, HOD1340-312/GBA, comprises an 850nm LED and a 1300nm PIN Diode. The pair facilitate full duplex communication over a single fibre and are designed to be used where a dual fibre solution is not possible or economical. Alternatively the duplexer can be used to double the capacity of an existing system. Each part consists of an on-axis port and an off-axis port loaded with the appropriate components, these are then coupled to the single fibre via integral lenses and a 3dB wavelength differentiating mirror within the duplexer body. In this configuration the two pairs of components can communicate in opposing directions simultaneously and independently of each other. Links of 2km+ are possible with this duplexer pair depending upon the receiver circuitry used. The duplexer housing is a special low profile design, being the same width as a standard ST for close mounting, the component ports are positioned to the rear and underside of the housing. Other standard options are available on request. These include two LEDs in one duplexer for single fibre multiplexing, PIN+Preamp receivers, VCSEL emitters or any other preferred components. Housing options include SC or FC/PC optical ports or a low profile ST housing the same height as a standard ST. Honeywell Control Systems Fibre Optic Components Single Fibre Duplex Modules HOD1340-312/GBA HOD2135-142/GBA HOD2135-142/GBA Duplexer 1300nm Transmit, 850nm Receive. Electro-Optical Specifications. 1300nm LED All tests made at 25°C unless otherwise specified Parameter Symbol Min. Typ. Max. Units Test Conditions Fibre Coupled Power VF VR λp tr tf BWE C 1290 115 15 µW dBm V 1350 nm 170 nm IF = 100mA 50/125µm fibre IF = 100mA IR = 2µA IF = 100mA DC IF = 100mA DC 4 ns 4 IF = 100mA, 50% Duty Cycle, f=12.5MHz MHz IF = 100mA dB/°C IF = 100mA 50 pF VF = 0V, f = 1MHz 850nm PIN Diode All tests made at 25°C unless otherwise specified Parameter Flux Responsivity Dark Current Response Time 10-90% Capacitance Isolation Symbol R ID BVR tR Min. Typ. 250 Max. Units A/W nA V ns Test Conditions λ = 850nm VR = 5V, f = 1MHz IR = 5V VR = 5V VR = 5V, f = 1MHz IF LED = 100mA DC Absolute Maximum Ratings Ordering Information - Duplexer Part Numbering Scheme The Duplexer design supports any combination of LED, Laser, PIN Diode or PIN+Preamp. The following table details the Duplexer part numbering scheme. Please contact Optoelectronics Sales on 01189 819511 to discuss any requirements not detailed in this data sheet. HOD X - X Port 1 Device Port 2 Port 1 Speed Port 2 Speed Optical Budget Connector Mounting Leads 1x = 850 LED 2x = 1300 LED 3x = 850 PIN 4x = 1300 PIN 5x = 850 P+P 6x = 1300 P+P 7x to 0x = Special 1 = < 3ns 2 = < 6ns 3 = < 10ns 4 = < 20ns 1 = < 10dB 2 = < 20dB 3 = < 30dB 4 = < 40dB A = SMA B = ST Low Profile C = FC/PC D = ST Close Mount E = SC F = Reserved G = ST Close Mount 2 X = Special B = PCB X = Special A = Normal B = Formed C = Special For example HOD1340-312/GBA defines :- 850 LED in Port 1 on axis 1300 PIN in Port 2 perpendicular axis LED < 10ns Rise/Fall Time PIN < 3ns Rise/Fall Time <20dB link budget when used with corresponding duplexer Close Mount Low profile , PCB housing, unformed leads Specifications may change at anytime and without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance, personally and through our literature, it is up to the customer to determine The suitability of the product in the application. Honeywell Control Systems Optolectronics Division Zodiac House,Calleva Park Aldermaston, Berkshire RG7 8HW MICRO SWITCH Honeywell Inc. Optoelectronics Facility 830 East Arapaho Road Richardson, Texas 75081

PDF Datasheet Preview

Fibre Optic Components Single Fibre Duplex Modules
• Full duplex over single fibre
• DC to 25MHz link bandwidth
• 2km+ link budget
• 40dB isolation
• Close mount ST housing
• Other options available

HOD1340-312/GBA HOD2135-142/GBA

The Honeywell HOD-XXXX series of dual wavelength 'Fibre Duplexers' allow communication over a single optical fibre link. Applications include full duplex data transmission, multiplexing two signals to a single fibre, LED coupled power measurements and reflected power measurements, depending upon the configuration of the duplexer.

The HOD2135-142/GBA comprises a 1300nm LED and an 850nm PIN Diode and its corresponding part, HOD1340-312/GBA, comprises an 850nm LED and a 1300nm PIN Diode. The pair facilitate full duplex communication over a single fibre and are designed to be used where a dual fibre solution is not possible or economical. Alternatively the duplexer can be used to double the capacity of an existing system.

Each part consists of an on-axis port and an off-axis port loaded with the appropriate components, these are then coupled to the single fibre via integral lenses and a 3dB wavelength differentiating mirror within the duplexer body. In this configuration the two pairs of components can communicate in opposing directions simultaneously and independently of each other. Links of 2km+ are possible with this duplexer pair depending upon the receiver circuitry used. The duplexer housing is a special low profile design, being the same width as a standard ST for close mounting, the component ports are positioned to the rear and underside of the housing.

Other standard options are available on request. These include two LEDs in one duplexer for single fibre multiplexing, PIN+Preamp receivers, VCSEL emitters or any other preferred components. Housing options include SC or FC/PC optical ports or a low profile ST housing the same height as a standard ST.

Honeywell Control Systems

Fibre Optic Components

Single Fibre Duplex Modules

HOD1340-312/GBA HOD2135-142/GBA

HOD2135-142/GBA Duplexer 1300nm Transmit, 850nm Receive. Electro-Optical Specifications.
1300nm LED All tests made at 25°C unless otherwise specified

Parameter

Symbol Min. Typ. Max. Units Test Conditions

Fibre Coupled Power

VF VR λp
tr tf BWE C
1290
115 15
µW dBm V 1350 nm 170 nm

IF = 100mA 50/125µm fibre IF = 100mA IR = 2µA IF = 100mA DC IF = 100mA DC
4 ns 4

IF = 100mA, 50% Duty Cycle, f=12.5MHz

MHz IF = 100mA dB/°C IF = 100mA
50 pF

VF = 0V, f = 1MHz
850nm PIN Diode All tests made at 25°C unless otherwise specified

Parameter Flux Responsivity

Dark Current

Response Time 10-90% Capacitance

Isolation

Symbol R ID BVR tR

Min.

Typ. 250

Max.

Units A/W nA V ns

Test Conditions λ = 850nm VR = 5V, f = 1MHz IR = 5V VR = 5V

VR = 5V, f = 1MHz

IF LED = 100mA DC

Absolute Maximum Ratings
Ordering Information - Duplexer Part Numbering Scheme

The Duplexer design supports any combination of LED, Laser, PIN Diode or PIN+Preamp. The following table details the Duplexer part numbering scheme. Please contact Optoelectronics Sales on 01189 819511 to discuss any requirements not detailed in this data sheet.

HOD X - X

Port 1 Device

Port 2

Port 1 Speed

Port 2 Speed

Optical Budget

Connector Mounting

Leads
1x = 850 LED 2x = 1300 LED 3x = 850 PIN 4x = 1300 PIN 5x = 850 P+P 6x = 1300 P+P 7x to 0x = Special
1 = < 3ns 2 = < 6ns 3 = < 10ns 4 = < 20ns
1 = < 10dB 2 = < 20dB 3 = < 30dB 4 = < 40dB

A = SMA B = ST Low

Profile C = FC/PC D = ST Close

Mount E = SC F = Reserved G = ST Close

Mount 2 X = Special

B = PCB X = Special

A = Normal B = Formed C = Special

For example HOD1340-312/GBA defines :-
850 LED in Port 1 on axis 1300 PIN in Port 2 perpendicular axis LED < 10ns Rise/Fall Time PIN < 3ns Rise/Fall Time <20dB link budget when used with corresponding duplexer Close Mount Low profile , PCB housing, unformed leads

Specifications may change at anytime and without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance, personally and through our literature, it is up to the customer to
determine The suitability of the product in the application.

Honeywell Control Systems Optolectronics Division Zodiac House,Calleva Park Aldermaston, Berkshire RG7 8HW

MICRO SWITCH Honeywell Inc. Optoelectronics Facility 830 East Arapaho Road Richardson, Texas 75081

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HOD1340-312/GBA Datasheet file may be downloaded here without warranties.

Datasheet ID: HOD1340-312/GBA 636495