HMD5000

HMD5000 Datasheet

HMD5000

Part	Datasheet
HMD5000	HMD5000 (pdf)

PDF Datasheet Preview
Compassing Navigation Systems Attitude Reference Magnetic Anomoly Detection Proximity Detection Laboratory Instrumentation Traffic and Vehicle Detection SENSOR PRODUCTS Preliminary Hand Held Display Module HMD5000 H and Held Display Module for digital magnetic sensor products. Displays heading, pitch and roll information when connected to the HMR3000 Digital Compass Module. If used with the HMR2300 Smart Digital Magnetometer, magnetic field readings in the X, Y and Z directions, as well as the magnitude of all three axes combined are shown. Hand Held Portable, runs on batteries, easy to use in field applications Flexible Design Works with Honeywell's HMR3000 Digital Compass Module or Honeywell's HMR2300 Smart Digital Magnetometer The HMD5000 is a small hand held unit with actual case dimensions of x inches. It weighs pounds. The interface cable is 3 feet long and has a female 9-pin “D” connector. The accuracy and resolution of the HMD500 is dependent on the instrument with which it is used the HMR3000 Digital Compass Module or the HMR2300 Smart Digital Magnetometer. Input Power Requirements Supply Voltage 6-15 Vdc Unregulated Power 72 mA 9 Vdc 300mA at Power Up Interface Cable Pin Assignments Pin Name 2 RD 3 TD 5 GND 9 V+ Description RS-232 Receive In RS-232 Transmit Out Power and Signal Ground Unregulated Power When outputting data the LCD display is divided into four quadrants. Each quadrant being 8 segments wide. When connected to the HMR2300 Smart Digital Magnetometer the display outputs magnetic field strength data in the X, Y and Z axes along with Magnitude. Magnitude is calculated using the formula X2 + Y2 + Z2. Figure 1 illustrates this output in both the “Gauss” and “Counts” mode. If the display is interfaced to an HMR3000 Digital Compass, the output consists of Heading, Pitch and Roll data with Status indicators for each reading if it is out of range. Figure 2 shows the compass output in both Degree and Mils mode. X-Axis Y-Axis HMD2300 X-Axis Y-Axis +15,446 - 2,034 -14,837 +23,223 Z-Axis Magnitude Z-Axis Magnitude Gauss Mode Counts Mode Figure Sample output when connected to an HMR2300 Heading Status HMD3000 Heading Status CH - P R 394 M - 25 P OP OR +768 R

PDF Datasheet Preview

Compassing Navigation Systems Attitude Reference Magnetic Anomoly Detection Proximity Detection Laboratory Instrumentation Traffic and Vehicle Detection

SENSOR PRODUCTS Preliminary

Hand Held Display Module

HMD5000

H and Held Display Module for digital magnetic sensor products. Displays heading, pitch and roll information when connected to the HMR3000 Digital Compass Module. If used with the HMR2300 Smart Digital Magnetometer, magnetic field readings in the X, Y and Z directions, as well as the magnitude of all three axes combined are shown.

Hand Held

Portable, runs on batteries, easy to use in field applications

Flexible Design Works with Honeywell's HMR3000 Digital Compass Module or Honeywell's HMR2300 Smart Digital Magnetometer

The HMD5000 is a small hand held unit with actual case dimensions of x inches. It weighs pounds. The interface cable is 3 feet long and has a female 9-pin “D” connector. The accuracy and resolution of the HMD500 is dependent on the instrument with which it is used the HMR3000 Digital Compass Module or the HMR2300 Smart Digital Magnetometer.

Input Power Requirements

Supply Voltage
6-15 Vdc Unregulated

Power
72 mA 9 Vdc 300mA at Power Up

Interface Cable Pin Assignments

Pin Name 2 RD 3 TD 5 GND 9 V+

Description RS-232 Receive In RS-232 Transmit Out Power and Signal Ground Unregulated Power

When outputting data the LCD display is divided into four quadrants. Each quadrant being 8 segments wide.

When connected to the HMR2300 Smart Digital Magnetometer the display outputs magnetic field strength data in the X, Y and Z axes along with Magnitude. Magnitude is calculated using the formula X2 + Y2 + Z2. Figure 1 illustrates this output in both the “Gauss” and “Counts” mode.

If the display is interfaced to an HMR3000 Digital Compass, the output consists of Heading, Pitch and Roll data with Status indicators for each reading if it is out of range. Figure 2 shows the compass output in both Degree and Mils mode.

X-Axis

Y-Axis

HMD2300

X-Axis

Y-Axis
+15,446 - 2,034 -14,837 +23,223

Z-Axis

Magnitude

Z-Axis

Magnitude

Gauss Mode

Counts Mode

Figure Sample output when connected to an HMR2300

Heading

Status

HMD3000

Heading

Status

CH - P R
394 M - 25 P

OP OR +768 R

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HMD5000 Datasheet file may be downloaded here without warranties.

Datasheet ID: HMD5000 636270