FH18-27S-0.3SHW

FH18-27S-0.3SHW Datasheet

FH18 Series

Part	Datasheet
FH18-27S-0.3SHW	FH18-27S-0.3SHW (pdf)

Related Parts	Information
FH18-27S-0.3SHW(55)	FH18-27S-0.3SHW(55)
FH18-17S-0.3SHW(55)	FH18-17S-0.3SHW(55)
FH18-51S-0.3SHW(55)	FH18-51S-0.3SHW(55)
FH18-39S-0.3SHW(55)	FH18-39S-0.3SHW(55)
FH18-21S-0.3SHW(55)	FH18-21S-0.3SHW(55)
FH18-25S-0.3SHW(55)	FH18-25S-0.3SHW(55)
FH18-25S-0.3SHW	FH18-25S-0.3SHW
FH18-21S-0.3SHW	FH18-21S-0.3SHW
FH18-39S-0.3SHW	FH18-39S-0.3SHW
FH18-17S-0.3SHW	FH18-17S-0.3SHW
FH18-51S-0.3SHW	FH18-51S-0.3SHW

PDF Datasheet Preview
Low Profile 0.3mm Pitch Connectors For FPC FH18 Series 1.8mm height above the mounting surface 1.8mm sFeatures Low profile 0.3mm pitch FPC connectors In response to continuous miniturization of products, the demand for smaller contact spacing on connectors is increasing. Flexible printed circuits FPC with contact pitch of 0.3mm are used with increased frequency. FH18 series connectors fullfill this requirement. In addition, these connectors occupy less board space and are lighter than comparable connectors with contacts spaced at 0.5mm. Improved Retention of FPC Two types of contacts design are combined in the FH18 connector, zero insertion force ZIF and low insertion force LIF . Inserted FPC is held in place by the LIF contact, allowing operator to close down the actuator and engage the ZIF contacts to assure complete connection. Easy to use Flip-Lock Flip-lock rotating type ZIF mechanism enables good connectivity of FPC by a simple operation and light force. No board space is required for flip lock operation as compared to slide lock ZIF connectors. Placement on Board The leads are on two sides of the connector, spaced on 0.6mm and are visible for solder joint inspection. Flat top surface of the connector allows board placement with automated equipment. Variety of Contact Positions The connectors are available with 17,21,25,27,39,45 and 51 contacts. sApplications Notebook computers, printers, PDAs, digital cameras and other compact devices for interconnecting the main circuit board with the LCD, PDP Plasma Display ,HDD or other device. LIF terminal contacts dFiPreCctiinosnertion FPC Non ZIF Contact Retention of FPC Connection completed Lever closed ZIF contact * LIF Low insertion Force * ZIF Zero insertion Force sProduct Specifications Rating Current rating 0.15A Operating temperature range Voltage rating 30V AC Operating humidity range -40ç to +85ç Note 1 Relative humidity 90% max. without condensation Storage temperature range -10ç to +50ç Note 2 Storage humidity range Relative humidity 90% max. without condensation Applicable FPC t=0.2±0.03 Solder plating Note 4 Item Specification 1.Insulation resistance 50M ohms minimum 2.Withstanding voltage No flashover or insulation breakdown. 3.Contact resistance 100m ohms maximum 4.Durability Contact resistance 100m ohms maximum Insertion/withdrawal No damage, cracks, or parts dislocation. 5.Vibration No electrical discontinuity of 1µs or more Contact resistance 100m ohms maximum No damage, cracks, or parts dislocation. sOrdering Information Material LCP Phosphor bronze FH18 - 27S - SHW 05 Finish Color Beige Color Black Solder plating Solder plating Remarks UL 94V-0 1 Series name FH18 2 Number of contacts 17, 21, 25, 27, 39, 45, 51 3 Contact pitch 0.3mm 4 Contact style SHW SMT horizontal mounting type 5 Plating specifications No symbol Solder plating 05 Gold plating BConnector Operating instruction Operating Instruction FPC Flat Printed Circuit Insertion A. Lift up carefully the lever to 90° max. angle. Do not forcefully exceed the 90° angle, as this may cause damage to connectoror the solder joints. B. Insert the FPC in the slot. Assure that it is fully and straight inserted, with conductive surface facing down. Slight friction of the LIF contacts will be felt and the FPC will remain inserted. FPC conductor surface C. Push the lever down to a fully closed position. FPC removal A. Lift the lever up to a 90° angle. B. Slide out the FPC untill completely free. A B P=0.6 Contact #1 Position indicator P=0.6 C D Indicates the number of contacts E FPC slot dimension* 1.8 Lead is included Notes 1 Indicates the distance from J surface. 2 The coplanarity of each lead and metal fitting within 0.1. coplanarity The distance between the lowest and highest land 3 This connector uses LIF Low Insertion Force and ZIF Zero Insertion Force contact design. Slight friction will be felt during insertion of FPC in the slot. Full insertion of FPC is required for secure connection. Unit mm CL No. Number of contacts FH18-17S-0.3SHW 586-0684-5

PDF Datasheet Preview

Low Profile 0.3mm Pitch Connectors For FPC

FH18 Series
1.8mm height above the mounting surface
1.8mm
sFeatures

Low profile 0.3mm pitch FPC connectors

In response to continuous miniturization of products, the demand for smaller contact spacing on connectors is increasing. Flexible printed circuits FPC with contact pitch of 0.3mm are used with increased frequency. FH18 series connectors fullfill this requirement. In addition, these connectors occupy less board space and are lighter than comparable connectors with contacts spaced at 0.5mm.

Improved Retention of FPC

Two types of contacts design are combined in the FH18 connector, zero insertion force ZIF and low insertion force LIF . Inserted FPC is held in place by the LIF contact, allowing operator to close down the actuator and engage the ZIF contacts to assure complete connection.

Easy to use Flip-Lock

Flip-lock rotating type ZIF mechanism enables good connectivity of FPC by a simple operation and light force. No board space is required for flip lock operation as compared to slide lock ZIF connectors.

Placement on Board

The leads are on two sides of the connector, spaced on 0.6mm and are visible for solder joint inspection. Flat top surface of the connector allows board placement with automated equipment.

Variety of Contact Positions

The connectors are available with 17,21,25,27,39,45 and 51 contacts.
sApplications

Notebook computers, printers, PDAs, digital cameras and other compact devices for interconnecting the main circuit board with the LCD, PDP Plasma Display ,HDD or other device.

LIF terminal contacts
dFiPreCctiinosnertion FPC

Non ZIF Contact Retention of FPC

Connection completed

Lever closed

ZIF contact
* LIF Low insertion Force * ZIF Zero insertion Force
sProduct Specifications

Rating

Current rating 0.15A Operating temperature range Voltage rating 30V AC Operating humidity range
-40ç to +85ç Note 1 Relative humidity 90% max. without condensation

Storage temperature range -10ç to +50ç Note 2 Storage humidity range Relative humidity 90% max.
without condensation

Applicable FPC t=0.2±0.03 Solder plating Note 4

Item

Specification
1.Insulation resistance 50M ohms minimum
2.Withstanding voltage No flashover or insulation breakdown.
3.Contact resistance 100m ohms maximum
4.Durability

Contact resistance 100m ohms maximum

Insertion/withdrawal No damage, cracks, or parts dislocation.
5.Vibration

No electrical discontinuity of 1µs or more Contact resistance 100m ohms maximum No damage, cracks, or parts dislocation.
sOrdering Information

Material LCP

Phosphor bronze

FH18 - 27S - SHW 05

Finish Color Beige Color Black Solder plating Solder plating

Remarks

UL 94V-0
1 Series name

FH18
2 Number of contacts 17, 21, 25, 27, 39, 45, 51
3 Contact pitch
0.3mm
4 Contact style

SHW SMT horizontal mounting type
5 Plating specifications No symbol Solder plating
05 Gold plating

BConnector Operating instruction

Operating Instruction

FPC Flat Printed Circuit Insertion

A. Lift up carefully the lever to 90° max. angle. Do not forcefully exceed the 90° angle, as this may cause damage to connectoror the solder joints.

B. Insert the FPC in the slot.

Assure that it is fully and straight inserted, with
conductive surface facing down.

Slight friction of the LIF contacts will be felt and the

FPC will remain inserted.

FPC conductor surface

C. Push the lever down to a fully closed position.

FPC removal

A. Lift the lever up to a 90° angle. B. Slide out the FPC untill completely free.

A B P=0.6

Contact #1 Position indicator

P=0.6 C D

Indicates the number of contacts

E FPC slot dimension*
1.8 Lead is included

Notes 1 Indicates the distance from J surface. 2 The coplanarity of each lead and metal fitting within 0.1. coplanarity The distance between the lowest and highest land 3 This connector uses LIF Low Insertion Force and ZIF Zero Insertion Force contact design. Slight friction will be felt during insertion of FPC in the slot. Full insertion of FPC is required for secure connection.

Unit mm

CL No.

Number of contacts

FH18-17S-0.3SHW
586-0684-5

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived FH18-27S-0.3SHW Datasheet file may be downloaded here without warranties.

Datasheet ID: FH18-27S-0.3SHW 636136