Z1002-00

Z1002-00 Datasheet

TRACK PIN INSERTION TOOL Z1002-00

Part	Datasheet
Z1002-00	Z1002-00 (pdf)

PDF Datasheet Preview
TRACK PIN INSERTION TOOL Z1002-00 HARWIN This Insertion Tool has been designed for use with the following track pins: T1558-46 T1562-46 T1559-46 T1563-46 T1560-46 T1564-46 T1561-46 T1565-46 TO LOAD TOOL Ensure that the first track pin on the strip is straight and in line. If not, gently bend into alignment. Insert the strip of pins into the plastic feed tube until resistance is felt. The tapered end of the pin should be inserted first Depress thumb knob several times to index pins fully, until one protrudes below the insertion head. If pins will not index, rotate pins in plastic tube until flexing occurs. Index pin forward For optimum snap-off, adjust the screw hexagonal nose on the insertion head, i.e. the head of the pins just protrudes below the level of the screw. The tool is now loaded and ready to use. Harwin North America T +1 603 893 5376 F +1 603 893 5396 E W: IS-06 Issue 3 Date C/Note 9874 Harwin Europe T +44 0 23 9231 4545 F +44 0 23 9231 4590 Harwin Asia T +65 6 779 4909 F +65 6 779 3868 E W: TO FIT TRACK PINS TO PC BOARD Insert the first track pin into the PC board’s hole, pushing down firmly Insert into PC Board Twist the tool sideways to approximately 45 degrees and back to obtain snap-off. Detach Lift the tool away from the board, and index the next track pin forward using the thumb knob. Repeat operations 1 to 2 until all holes are filled. To solder the top side, apply the soldering iron bit to the top of the track pin head and push down, whilst applying the solder under the track pin head. Solder Fit all the other components into the PC board and then hand or flow-solder the underside of the board. CARE OF TOOLS After repeated use, the tool may require cleaning to remove solder particles from the feed mechanism. To clean, blow air through the transverse cleaning hole provided. IS-06 Issue 3 Date C/Note 9874

PDF Datasheet Preview

TRACK PIN INSERTION TOOL Z1002-00

HARWIN

This Insertion Tool has been designed for use with the following track pins:

T1558-46 T1562-46

T1559-46 T1563-46

T1560-46 T1564-46

T1561-46 T1565-46

TO LOAD TOOL

Ensure that the first track pin on the strip is straight and in line. If not, gently bend into alignment.

Insert the strip of pins into the plastic feed tube until resistance is felt. The tapered end of the pin should be inserted first

Depress thumb knob several times to index pins fully, until one protrudes below the insertion head. If pins will not index, rotate pins in plastic tube until flexing occurs.

Index pin
forward

For optimum snap-off, adjust the screw hexagonal nose on the insertion head, i.e. the head of the pins just protrudes below the level of the screw.

The tool is now loaded and ready to use.

Harwin North America T +1 603 893 5376 F +1 603 893 5396 E W:

IS-06 Issue 3 Date C/Note 9874

Harwin Europe T +44 0 23 9231 4545 F +44 0 23 9231 4590

Harwin Asia T +65 6 779 4909 F +65 6 779 3868 E W:

TO FIT TRACK PINS TO PC BOARD

Insert the first track pin into the PC board’s hole, pushing down firmly

Insert into PC Board

Twist the tool sideways to approximately 45 degrees and back to obtain snap-off.

Detach

Lift the tool away from the board, and index the next track pin forward using the thumb knob.

Repeat operations 1 to 2 until all holes are filled. To solder the top side, apply the soldering iron bit to the top of the track pin head and push
down, whilst applying the solder under the track pin head.

Solder

Fit all the other components into the PC board and then hand or flow-solder the underside of the board.

CARE OF TOOLS

After repeated use, the tool may require cleaning to remove solder particles from the feed mechanism. To clean, blow air through the transverse cleaning hole provided.

IS-06 Issue 3 Date C/Note 9874

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived Z1002-00 Datasheet file may be downloaded here without warranties.

Datasheet ID: Z1002-00 636022