S5U13781P00C100
S5U13781P00C100 Datasheet
S5U13781P00C100 Evaluation Board User
| Part | Datasheet |
|---|---|
S5U13781P00C100 |
S5U13781P00C100 (pdf) |
| PDF Datasheet Preview |
|---|
| S1D13781 Display Controller S5U13781P00C100 Evaluation Board User Manual SEIKO EPSON CORPORATION Evaluation board/kit and Development tool important notice This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration, or development purposes only. Do not use it for other purpose. It is not intended to meet the requirement of design for finished product. This evaluation board/kit or development tool is intended for use by an electronics engineer, and it is not the product for consumer. The user should use this goods properly and safely. Seiko Epson dose not assume any responsibility and liability of any kind of damage and/or fire coursed by usage of it. User should cease to use it when any abnormal issue occurs even during proper and safe use. The part used for this evaluation board/kit or development tool is changed without any notice. NOTICE No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from the Ministry of International Trade and Industry or other approval from another government agency. All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective companies. SEIKO EPSON CORPORATION 2009 - 2010, All rights reserved. Table of Contents Chapter 1 Introduction 5 Chapter 2 Features 6 Chapter 3 Installation and Configuration 7 CNF[2:0] Configuration 7 Configuration Switches 8 Configuration Jumpers 9 Zero Ohm Resistor Configuration 11 Power Requirements 11 IOVDD, COREVDD, PLLVDD 11 3.3V 11 Backlight Power Supply for LCD Panel 11 LED Status Indicators 13 Chapter 4 Connectors 14 CN1, CN2 Panel Interface Connector 14 CN3, CN4 Host Bus Interface Connector 14 P1, P2 Connecting to the Epson S5U13U00P00C100 USB Adapter Board 15 Chapter 5 Technical Description 17 Current Measurement 17 Oscillator Support for CLKI input 17 Hardware Reset 18 Chapter 6 Parts List 19 Chapter 7 Schematic Diagrams 22 Chapter 8 Board Layout 27 Chapter 9 References 29 Documents 29 Document Sources 29 EPSON Chapter 1 Introduction Chapter 1 Introduction This manual describes the setup and operation of the S5U13781P00C100 Evaluation Board. The evaluation board is designed as an evaluation platform for the S1D13781 Display Controller. The S5U13781P00C100 evaluation board can be used with many native platforms via the host connector which provides the appropriate signals to support a variety of CPUs. The S5U13781P00C100 evaluation board can also connect to the S5U13U00P00C100 USB Adapter board so that it can be used with a laptop or desktop computer, via USB We appreciate your comments on our documentation. Please contact us via email at Chapter 2 Features Chapter 2 Features The S5U13781P00C100 Evaluation Board includes the following features • QFP 100pin S1D13781F00A100 Display Controller • Headers for connection to various Host Bus Interfaces including termination switching for un-used pins • Headers for connection to the S5U13U00P00C100 USB Adapter board Note The SPI interface is not available when the S5U13781P00C100 evaluation board is used with the S5U13U00P00C100 USB adapter board. • Headers for connection to various LCD panels • On-board 24MHz crystal EPSON SG-210 or RIVER ELETEC FCXO-05 • 14-pin DIP socket if an oscillator for CLKI input is required • 5.0V input power • On-board voltage regulator with 1.5V output, for CORE/PLLVDD • On-board voltage regulator with adjustable 1.5~3.8V output, for IOVDD • On-board voltage regulator with 3.3V output, for on-board OSC • On-board voltage regulator with adjustable 12~30V output, 350~100mA max., to provide power for LED back- light of LCD panels. EPSON Chapter 3 Installation and Configuration Chapter 3 Installation and Configuration The S5U13781P00C100 evaluation board incorporates a DIP switch, jumpers, and 0 ohm resistors which allow it to be used with a variety of different configurations. CNF[2:0] Configuration The S1D13781 has 3 configuration inputs CNF[2:0], which are used to configure the S1D13781 host interface type through DIP switch SW1. Depending on the CNF[2:0] setting, some host interface pins will not be used. Those pins should be terminated by SW2 and SW3. Table 3-1 Host Interface Pin Mapping S1D13781 Direct 16-bit Direct 16-bit Indirect 16-bit Indirect 16-bit Direct 8-bit Pin Name Mode 1 Mode 2 Mode 1 Mode 2 Indirect 8-bit CNF[2:0] RDU# |
| More datasheets: CYV15G0204RB-BGXC | HLMP-LD61-SWTZZ | HLMP-LB61-PT0ZZ | HLMP-LM61-X20ZZ | 17-300400 | 17-300380 | 17-300390 | SMP2-GC | 37765 | 37764 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived S5U13781P00C100 Datasheet file may be downloaded here without warranties.