Disc type Ordering code B72210S0621K331
Part | Datasheet |
---|---|
![]() |
B72210S0621K331 (pdf) |
PDF Datasheet Preview |
---|
Metal Oxide Varistor SIOV-S10K625G3S3 Data sheet Form FBLE3K/b File name S10K625G3S3 MODIFICATIONS New Issue Disc type Ordering code B72210S0621K331 REMARKS: Prepared by Collins-Hunt ISSUE DATE Release ISSUE signed PE / Collins-Hunt signed: signed QS / Zödl signed: PUBLISHER KH PE VAR PAGE 0/8 Metal Oxide Varistor SIOV-S10K625G3S3 Data sheet Disc type Ordering code B72210S0621K331 SIOV nomenclature: = Disk type = Rated disk diameter = Tolerance of varistor voltage at 1mA ±10% = Max. operating voltage Vrms = Taping Style G3 = Crimp style S3 Figure Dimensions given in Millimeters mm bmax = 12,0 hmax = 17,5 smax = 7,5 ± 0,8 = 0,8 ± 0,05 1 seating plane in accordance with IEC 60717 2 measured above carrier tape Electrical data: Maximum ratings Ta=85°C Max. Operating AC voltage Max. Operating DC voltage Surge current 8/20µs 1 time Energy absorption 2ms 1 time Average power dissipation Characteristics Ta=25°C Varistor voltage at 1mA Clamping voltage at 25 A 8/20µs Type. Capacitance at 1 kHz VRMS VDC Imax Wmax Pmax VV VC,max C = 625 V = 825 V = 2500 A = 68,0 J = 0,4 W = 1000 V ± 10% = 1650 V = 90 pF ISSUE DATE PUBLISHER KH PE VAR PAGE 1/8 Metal Oxide Varistor SIOV-S10K625G3S3 Data sheet Disc type Ordering code B72210S0621K331 V/I Characteristic: 5000 4000 vV 2000 VAR9152A 1000 800 600 100 80 10 -5 10 -4 10 -3 10 -2 10 -1 A 10 4 Derating: 10000 1000 100 10 x inf.. S10K385 680 imax. tr 0,1 10 1000 t r [µs] 10000 ISSUE DATE PUBLISHER KH PE VAR PAGE 2/8 Metal Oxide Varistor SIOV-S10K625G3S3 Data sheet Taping: Package Unit: 500 pcs./reel Lead spacing 7,5mm Disc type Ordering code B72210S0621K331 dmax = wmax = 360mm 64mm 31 ± 1,0mm 55mm typ. ISSUE DATE PUBLISHER KH PE VAR PAGE 3/8 Metal Oxide Varistor SIOV-S10K625G3S3 Data sheet Tape dimensions, in Millimeters mm : Disc type Ordering code B72210S0621K331 Definition Symbol Dimension Tolerance Remarks Body diameter Body thickness Lead diameter Sprocket hole pitch Distance hole center to lead center Lead spacing Component deviation Component deviation Carrier tape width Adhesive tape width Sprocket hole position Adhesive tape position Distance hole center to top of the component Seating plane height Hole diameter Total tape thickness Cutting level 12,0 ± 0,05 12,7 ± 0,3 ± 1mm/20 sprocket holes 8,95 ± 0,8 ± 0,8 measured above carrier tape depending on s ± 2,0 measured at top of component body 18,0 ± 0,5 11,0 Peel-off force + 0,75/ Disc type Ordering code B72210S0621K331 Characteristics Varistor E Voltage L Clamping Voltage Test Methods/Description The voltage between two terminals with the specified measuring current applied is called Vv 1 mADC - 2 s . The maximum voltage between two terminals with the specified standard impulse current 8/20µs illustrated below applied. Peak Leading Edge Trailing Edge Specifications To meet the specified value. To meet the specified value. TS Rise Time µs Tr Decay time to half value µs O1 Nominal start Im Peak value C Surge current derating, 8/20 µs L Surge current derating, 2 ms 100 surge currents 8/20 µs , unipolar, interval 30 s, amplitude corresponding to derating curve for 20 µs 100 surge currents 2ms , unipolar, interval 120s, amplitude corresponding to derating curve for 2ms | V/V 1 mA | 10 % measured in direction of surge current No visible damage | V/V 1 mA | 10 % measured in direction of surge current No visible damage ISSUE DATE PUBLISHER KH PE VAR PAGE 5/8 Metal Oxide Varistor SIOV-S10K625G3S3 Data sheet Disc type Ordering code B72210S0621K331 Characteristics Tensile strength M E Vibration C H A Solderability N I C A L Test Methods/Description Specifications After gradually applying the force specified below and keeping the unit fixed for 10 seconds, the terminal shall be visually examined for any damage. | V/V 1 mA | No break of solder joint, no wire break Terminal diameter mm Force 5N 10 N 10 N 20 N After repeatedly applying a single harmonic vibration according to the table below. Thereafter, the unit shall be visually examined. | V/V 1 mA | No visible damage frequency range amplitude duration pulse: 10 55 Hz mm or 98 6 h 3 x 2 h sine wave After dipping the terminals to a depth of approximately 3 mm from the body in a soldering bath of 235°C for 5 seconds, the terminals shall be visually examined. The inspection shall be carried out under adequate light with normal eyesight or with the assistance of a magnifier capable of giving a magnification of 4 times to 10 times. The dipped surface shall be covered with a smooth and bright solder coating with no more than small amounts of scattered imperfections such as pinholes or unwetted or de-wetted areas. These imperfections shall not be concentrated in one area. ISSUE DATE PUBLISHER KH PE VAR PAGE 6/8 Metal Oxide Varistor SIOV-S10K625G3S3 Data sheet Disc type Ordering code B72210S0621K331 Characteristics M Resistance to E soldering heat C H A N Electric strength I C A L Test Methods/Description Specifications Each lead shall be dipped into a solder bath having a temperature of 260 ± 5°C to a point to mm from the body of the unit, be held there for 10 ± 1 s and then be stored at room temperature and normal humidity for 1 to 2 hours. The change of Vv and mechanical damages shall be examined. 2500 VRMS, 10 s The varistor is placed in a container holding ± mm diameter metal balls such that only the terminations of the varistor are protruding. The specified voltage shall be applied between both terminals of the specimen connected together and the electrode inserted between the metal balls. | V/V 1 mA | No visible damage No breakdown ISSUE DATE PUBLISHER KH PE VAR PAGE 7/8 Metal Oxide Varistor SIOV-S10K625G3S3 Data sheet Disc type Ordering code B72210S0621K331 Characteristics E Max. AC operating voltage V Damp heat, steady state R Climatic sequence Fast temperature cycling Test Methods/Description Specifications After being continuously applied the maximum allowable voltage at 85 ± 2°C for 1000 hours, the specimen shall be stored at room temperature and normal humidity for 1 to 2 hours. Thereafter, the change of Vv shall be measured. The specimen shall be subjected to 40 ± 2°C, 90 to 95 % r.H. for 56 days without load and then stored at room temperature and normal humidity for 1 to 2 hours. Thereafter, the change of Vv shall be measured. The specimen shall be subjected to a dry heat at +85°C, 16 h b damp heat, 1st cycle 55°C, 93 % r.H., 24 h c cold, -40°C, 2 h d damp heat, additional 5 cycles 55°C, 93 % r.H., 24 h/cycle Then the specimen shall be stored at room temperature and normal humidity for 1 to 2 hours. Thereafter, the change of Vv shall be measured. The temperature cycle shown below shall be repeated 5 times. Then the specimen shall be stored at room temperature and normal humidity for 1 to 2 hours. The change of Vv and mechanical damage shall be examined. | V/V 1 mA | 10 % | V/V 1 mA | 10 % | V/V 1 mA | 10 % | V/V 1 mA | No visible damage Step 1 2 3 Temperature °C -40 ± 3 transition time 85 ± 2 Period min. 30 ± 3 < 10 s 30 ± 3 Note More details can be found in the data book 'SIOV Metal Oxide Varistors', Ordering No. EPC 62002-7600 EPCOS AG Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI German Electrical and Electronic Manufacturers' Association , unless otherwise agreed. ISSUE DATE PUBLISHER KH PE VAR PAGE 8/8 |
More datasheets: 5082-2835 | 5082-2811 | 5082-2810 | 5082-2835#T50 | 1N5711 | TUF2AAPE | CY25701FJXCT | CY25701FJXC | QT1081-ISG | 1230 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived B72210S0621K331 Datasheet file may be downloaded here without warranties.