Ordering Code B66348A1018T001
Part | Datasheet |
---|---|
![]() |
B66348A1018T1 (pdf) |
PDF Datasheet Preview |
---|
Ferrites and accessories Series/Type ER 42_22_15 The following products presented in this data sheet are being withdrawn. Ordering Code B66348A1018T001 Substitute Product Date of Withdrawal 2015-05-22 Deadline Last Orders 2015-08-31 Last Shipments 2015-11-30 For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at EPCOS AG Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. EPCOS AG is a TDK Group Company. ER 42/22/15 Core • Round center leg particularly suitable for use of thick winding wires or tapes • For compact winding design with low leakage inductance • Delivery mode single units Magnetic characteristics per set = le = 99 mm Ae = 170 mm2 Amin = 170 mm2 Ve = 16800 mm3 Approx. weight 84 g/set B66347 Ungapped Material AL value nH BS* mT 3200 1480 320 3700 1710 320 PV W/set Ordering code < 200 mT, 25 kHz, 100 °C B66347G0000X127 < 200 mT, 100 kHz, 100 °C B66347G0000X187 * H = 250 A/m f = 10 kHz T = 100 °C Gapped Material g mm AL value approx. Ordering code B66347G1000X127 The AL value in the table applies to a core set comprising one ungapped core dimension g = 0 and one gapped core dimension g > Calculation factors for formulas, see “E cores general information” Material N27 N87 Relationship between air gap AL value K1 25 °C K2 25 °C Calculation of saturation current K3 25 °C 415 401 K4 25 °C K3 100 °C K4 100 °C Validity range: K1, K2 mm < s < mm K3, K4 110 nH < AL < 1100 nH Please read Cautions and warnings and Important notes at the end of this document. 2 06/13 ER 42/22/15 Accessories B66348 Coil former Material: GFR polyterephthalate UL 94 V-0, insulation class to IEC 60085: F max. operating temperature 155 °C , color code black Valox GE PLASTICS B V Solderability to IEC 60068-2-20, test Ta, method 1 aging 3 235 °C, 2 s Resistance to soldering heat to IEC 60068-2-20, test Tb, method 1B 350 °C, s Winding: see Data Book 2013, chapter “Processing notes, Coil former Sections AN mm2 lN mm AR value Pins Ordering code B66348A1018T001 Please read Cautions and warnings and Important notes at the end of this document. 3 06/13 Ferrites and accessories Cautions and warnings Cautions and warnings Mechanical stress and mounting Ferrite cores have to meet mechanical requirements during assembling and for a growing number of applications. Since ferrites are ceramic materials one has to be aware of the special behavior under mechanical load. As valid for any ceramic material, ferrite cores are brittle and sensitive to any shock, fast changing or tensile load. Especially high cooling rates under ultrasonic cleaning and high static or cyclic loads can cause cracks or failure of the ferrite cores. For detailed information see chapter “Definitions”, section Effects of core combination on AL value Stresses in the core affect not only the mechanical but also the magnetic properties. It is apparent that the initial permeability is dependent on the stress state of the core. The higher the stresses are in the core, the lower is the value for the initial permeability. Thus the embedding medium should have the greatest possible elasticity. For detailed information see chapter “Definitions”, section Heating up Ferrites can run hot during operation at higher flux densities and higher frequencies. NiZn-materials The magnetic properties of NiZn-materials can change irreversible in high magnetic fields. Processing notes The start of the winding process should be soft. Else the flanges may be destroid. To strong winding forces may blast the flanges or squeeze the tube that the cores can no more be mount. To long soldering time at high temperature >300 °C may effect coplanarity or pin arrangement. Not following the processing notes for soldering of the J-leg terminals may cause solderability problems at the transformer because of pollution with Sn oxyd of the tin bath or burned insulation of the wire. For detailed information see chapter “Processing notes”, section The dimensions of the hole arrangement have fixed values and should be understood as a recommendation for drilling the printed circuit board. For dimensioning the pins, the group of holes can only be seen under certain conditions, as they fit into the given hole arrangement. To avoid problems when mounting the transformer, the manufacturing tolerances for positioning the customers’ drilling process must be considered by increasing the hole diameter. 4 06/13 Ferrites and accessories Symbols and terms Symbols and terms A Ae AL AL1 Amin AN AR B BDC BR BS C0 CDF DF d Ea f fcutoff fmax fmin fr fCu g H HDC Hc h 2 I IDC J k k3 k3c L Meaning Cross section of coil Effective magnetic cross section Inductance factor AL = L/N2 Minimum inductance at defined high saturation Minimum core cross section Winding cross section Resistance factor AR = RCu/N2 RMS value of magnetic flux density Flux density deviation Peak value of magnetic flux density Peak value of flux density deviation DC magnetic flux density Remanent flux density Saturation magnetization Winding capacitance Core distortion factor Relative disaccommodation coefficient DF = Disaccommodation coefficient Activation energy Frequency Cut-off frequency Upper frequency limit Lower frequency limit Resonance frequency Copper filling factor Air gap RMS value of magnetic field strength Peak value of magnetic field strength DC field strength Coercive field strength Hysteresis coefficient of material Relative hysteresis coefficient RMS value of current Direct current Peak value of current Polarization Boltzmann constant Third harmonic distortion Circuit third harmonic distortion Inductance 5 06/13 Unit mm2 mm2 nH nH mm2 mm2 = Vs/m2, mT Vs/m2, mT Vs/m2, mT Vs/m2, mT Vs/m2, mT Vs/m2, mT Vs/m2, mT F = As/ V J Hz Hz Hz Hz Hz mm A/m A/m A/m A/m cm/A cm/A A A A Vs/m2 J/K H = Vs/A Ferrites and accessories Symbols and terms L0 LH Lp Lrev Ls le lN N PCu Ptrans PV PF Q R RCu Rh Ri Rp Rs Rth RV s T TC t tv |
More datasheets: MGA-22103-TR1G | MGA-22103-BLKG | FQA16N50 | ATA6620N-TAQY | AS1312-BTDM-27 | ASMT-MWA0-NJKW0 | ASMT-MWA0-NJJ00 | ASMT-MWA0-NJKZ0 | ASMT-MWA0-NKKZ0 | ASMT-MWA0-NKK00 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived B66348A1018T1 Datasheet file may be downloaded here without warranties.