B41044A5477M

B41044A5477M Datasheet

B41044, B43044 December 2010

Part	Datasheet
B41044A5477M	B41044A5477M (pdf)

Related Parts	Information
B41044A2159M	B41044A2159M
B41044A2109M	B41044A2109M
B41044A2226M	B41044A2226M
B41044A2227M	B41044A2227M
B41044A2228M	B41044A2228M
B41044A2337M	B41044A2337M
B41044A2338M	B41044A2338M
B41044A2336M	B41044A2336M
B41044A2158M	B41044A2158M
B41044A5338M	B41044A5338M
B41044A5475M	B41044A5475M
B41044A5476M	B41044A5476M
B41044A5478M	B41044A5478M
B41044A5687M	B41044A5687M
B41044A6105M	B41044A6105M
B41044A6106M	B41044A6106M
B41044A6108M	B41044A6108M
B41044A6157M	B41044A6157M
B41044A6224M	B41044A6224M
B41044A6158M	B41044A6158M
B41044A6107M	B41044A6107M
B41044A3228M	B41044A3228M
B41044A4157M	B41044A4157M
B41044A4108M	B41044A4108M
B41044A8107M	B41044A8107M
B41044A4107M	B41044A4107M
B41044A6225M	B41044A6225M
B41044A3688M	B41044A3688M
B41044A3687M	B41044A3687M
B41044A3478M	B41044A3478M
B41044A3477M	B41044A3477M
B41044A3476M	B41044A3476M
B41044A3338M	B41044A3338M
B41044A4106M	B41044A4106M
B41044A3336M	B41044A3336M
B41044A2476M	B41044A2476M
B41044A3227M	B41044A3227M
B41044A3226M	B41044A3226M
B41044A3158M	B41044A3158M
B41044A3157M	B41044A3157M
B41044A3109M	B41044A3109M
B41044A3108M	B41044A3108M
B41044A3107M	B41044A3107M
B41044A2688M	B41044A2688M
B41044A2687M	B41044A2687M
B41044A2478M	B41044A2478M
B41044A2477M	B41044A2477M
B41044A3337M	B41044A3337M
B41044A9226M	B41044A9226M
B41044A7687M	B41044A7687M
B41044A8227M	B41044A8227M
B41044A8335M	B41044A8335M
B41044A8336M	B41044A8336M
B41044A8337M	B41044A8337M
B41044A8475M	B41044A8475M
B41044A8476M	B41044A8476M
B41044A8477M	B41044A8477M
B41044A8687M	B41044A8687M
B41044A9106M	B41044A9106M
B41044A9107M	B41044A9107M
B41044A8157M	B41044A8157M
B41044A9225M	B41044A9225M
B41044A8108M	B41044A8108M
B41044A9227M	B41044A9227M
B41044A9335M	B41044A9335M
B41044A9336M	B41044A9336M
B41044A9337M	B41044A9337M
B41044A9475M	B41044A9475M
B41044A9476M	B41044A9476M
B41044A9477M	B41044A9477M
B41044A4158M	B41044A4158M
B41044A4337M	B41044A4337M
B41044B7108M	B41044B7108M
B41044A2157M	B41044A2157M
B41044A9157M	B41044A9157M
B41044A7157M	B41044A7157M
B41044A6227M	B41044A6227M
B41044A6228M	B41044A6228M
B41044A6335M	B41044A6335M
B41044A6336M	B41044A6336M
B41044A6337M	B41044A6337M
B41044A6474M	B41044A6474M
B41044A6475M	B41044A6475M
B41044A6476M	B41044A6476M
B41044A6477M	B41044A6477M
B41044A6687M	B41044A6687M
B41044A7106M	B41044A7106M
B41044A8226M	B41044A8226M
B41044A7108M	B41044A7108M
B41044A6226M	B41044A6226M
B41044A7158M	B41044A7158M
B41044A7226M	B41044A7226M
B41044A7227M	B41044A7227M
B41044A7228M	B41044A7228M
B41044A7336M	B41044A7336M
B41044A7337M	B41044A7337M
B41044A7338M	B41044A7338M
B41044A7475M	B41044A7475M
B41044A7476M	B41044A7476M
B41044A7477M	B41044A7477M
B41044A8106M	B41044A8106M
B41044A7107M	B41044A7107M
B41044A5227M	B41044A5227M
B41044A4226M	B41044A4226M
B41044A4227M	B41044A4227M
B41044A4336M	B41044A4336M
B41044A4338M	B41044A4338M
B41044A4476M	B41044A4476M
B41044A4477M	B41044A4477M
B41044A5337M	B41044A5337M
B41044A5228M	B41044A5228M
B41044A5226M	B41044A5226M
B41044A5158M	B41044A5158M
B41044A5157M	B41044A5157M
B41044A5108M	B41044A5108M
B41044A5107M	B41044A5107M
B41044A5106M	B41044A5106M
B41044A4688M	B41044A4688M
B41044A4687M	B41044A4687M
B41044A4478M	B41044A4478M
B41044A4228M	B41044A4228M
B41044A5336M	B41044A5336M
B43044A5107M	B43044A5107M
B43044A9107M	B43044A9107M
B43044A9106M	B43044A9106M
B43044A5686M	B43044A5686M
B43044A5476M	B43044A5476M
B43044A5475M	B43044A5475M
B43044A5336M	B43044A5336M
B43044A5335M	B43044A5335M
B43044A5127M	B43044A5127M
B43044A5106M	B43044A5106M
B43044A9226M	B43044A9226M
B43044A5226M	B43044A5226M
B43044A9336M	B43044A9336M
B43044A9476M	B43044A9476M
B43044A9686M	B43044A9686M
B43044F2106M	B43044F2106M
B43044F2107M	B43044F2107M
B43044F2157M	B43044F2157M
B43044F2226M	B43044F2226M
B43044F2227M	B43044F2227M
B43044F2336M	B43044F2336M
B43044A4476M	B43044A4476M
B43044F2686M	B43044F2686M
B43044A4336M	B43044A4336M
B43044F2476M	B43044F2476M
B43044A1157M	B43044A1157M
B43044A4686M	B43044A4686M
B43044A1107M	B43044A1107M
B43044A4226M	B43044A4226M
B43044A1226M	B43044A1226M
B43044A1227M	B43044A1227M
B43044A1336M	B43044A1336M
B43044A1337M	B43044A1337M
B43044A1476M	B43044A1476M
B43044A1686M	B43044A1686M
B43044A2107M	B43044A2107M
B43044A2157M	B43044A2157M
B43044A4106M	B43044A4106M
B43044A2227M	B43044A2227M
B43044A2336M	B43044A2336M
B43044A2476M	B43044A2476M
B43044A2686M	B43044A2686M
B43044A2226M	B43044A2226M
B43044A4107M	B43044A4107M
B41044A2107M	B41044A2107M
B41044A2108M	B41044A2108M

PDF Datasheet Preview
Aluminum electrolytic capacitors Single-ended capacitors Series/Type Date: B41044, B43044 December 2010 The following products presented in this data sheet are being withdrawn. Ordering Code Substitute Product B41044A8227M000 Date of Withdrawal 2012-04-13 Deadline Last Orders 2012-07-13 Last Shipments 2012-10-13 For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at EPCOS AG Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Single-ended capacitors Low impedance & high ripple current 105 °C B41044, B43044 Long-life grade capacitors for professional applications Power supplies RoHS-compatible High CV product Low impedance at high frequencies High reliability Useful life of 5000 h at 105 °C Construction Radial leads Aluminum case, fully insulated Charge-discharge proof Minus pole marking on the insulating sleeve Case with safety vent from diameter 8 mm Delivery mode Bulk Taped, Ammo pack Cut see chapter "Single-ended Taping, packing and lead configurations, Cut leads Chapter A " Kinked see chapter "Single-ended Taping, packing and lead configurations, Kinked leads Chapter A " Refer to chapter "Single-ended capacitors Taping, packing and lead configurations" for further details. Specifications and characteristics in brief Series B41044 B43044 Rated voltage VR 100 V DC 160 450 V DC Surge voltage VS VR 250 V DC VR at room temperature VR > 250 V DC VR at room temperature Rated capacitance CR 15000 µF Capacitance tolerance ±20% M Dissipation factor max. 20 °C, 120 Hz For capacitance higher than 1000 µF add for every increase of 1000 µF. 10 16 25 35 50 63 100 160 350 250 450 Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Series Leakage current Ileak B41044 VR 100 V DC Technical data and ordering codes B41044 CR 120 Hz Case dimensions 20 °C VR = V DC 5 x 11 5 x 11 5 x 11 5 x 11 1000 1500 10 x 20 2200 3300 4700 16 x 25 6800 16 x 25 10000 15000 VR = 10 V DC 22 33 47 100 150 220 330 470 5 x 11 5 x 11 5 x 11 5 x 11 x 11 x 11 8 x 8 x Zmax 100 kHz 20 °C IAC,R 100 kHz 105 °C mA 180 280 450 660 1100 1400 2100 2600 3000 180 280 450 Ordering code composition see below B41044A2226M* B41044A2336M* B41044A2476M* B41044A2107M* B41044A2157M* B41044A2227M* B41044A2337M* B41044A2477M* B41044A2687M* B41044A2108M* B41044A2158M* B41044A2228M* B41044A2338M* B41044A2478M* B41044A2688M* B41044A2109M* B41044A2159M* B41044A3226M* B41044A3336M* B41044A3476M* B41044A3107M* B41044A3157M* B41044A3227M* B41044A3337M* B41044A3477M* Composition of ordering code * = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and 18 x 25 18 x mm Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 40 B41044 Low impedance & high ripple current 105 °C Technical data and ordering codes B41044 CR 120 Hz Case dimensions 20 °C VR = 10 V DC 1000 10 x 16 1500 10 x 20 2200 3300 4700 16 x 25 6800 10000 VR = 16 V DC 5 x 11 5 x 11 5 x 11 5 x 11 10 x 16 1000 10 x 20 1500 2200 3300 16 x 25 4700 6800 Zmax 100 kHz 20 °C IAC,R 100 kHz 105 °C mA 660 850 1100 1400 1700 2100 2600 3000 180 280 450 660 850 1100 1400 1700 2100 2600 3000 Ordering code composition see below B41044A3687M* B41044A3108M* B41044A3158M* B41044A3228M* B41044A3338M* B41044A3478M* B41044A3688M* B41044A3109M* B41044A4106M* B41044A4226M* B41044A4336M* B41044A4476M* B41044A4107M* B41044A4157M* B41044A4227M* B41044A4337M* B41044A4477M* B41044A4687M* B41044A4108M* B41044A4158M* B41044A4228M* B41044A4338M* B41044A4478M* B41044A4688M* Composition of ordering code * = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and 18 x 25 18 x mm Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 40 B41044 Low impedance & high ripple current 105 °C Technical data and ordering codes B41044 CR 120 Hz Case dimensions 20 °C VR = 25 V DC 5 x 11 5 x 11 5 x 11 5 x 11 5 x 11 10 x 16 10 x 20 1000 1500 16 x 20 2200 16 x 25 3300 4700 VR = 35 V DC 5 x 11 5 x 11 5 x 11 5 x 11 10 x 16 Zmax 100 kHz 20 °C IAC,R 100 kHz 105 °C mA 180 280 450 660 850 1100 1400 2100 2600 3000 180 280 450 660 850 Ordering code composition see below B41044A5475M* B41044A5106M* B41044A5226M* B41044A5336M* B41044A5476M* B41044A5107M* B41044A5157M* B41044A5227M* B41044A5337M* B41044A5477M* B41044A5687M* B41044A5108M* B41044A5158M* B41044A5228M* B41044A5338M* B41044A5478M* B41044A7475M* B41044A7106M* B41044A7226M* B41044A7336M* B41044A7476M* B41044A7107M* B41044A7157M* B41044A7227M* B41044A7337M* Composition of ordering code * = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and 18 x 25 18 x mm Please read Cautions and warnings and Important notes at the end of this document. Page 10 of 40 B41044 Low impedance & high ripple current 105 °C Technical data and ordering codes B41044 CR 120 Hz Case dimensions 20 °C VR = 35 V DC 10 x 20 1000 1500 16 x 25 2200 3300 VR = 50 V DC 5 x 11 5 x 11 5 x 11 5 x 11 5 x 11 5 x 11 5 x 11 5 x 11 10 x 16 10 x 20 1000 16 x 25 1500 2200 Zmax 100 kHz 20 °C IAC,R 100 kHz 105 °C mA 1100 1400 1700 2100 2600 3000 18 25 40 55 65 90 120 150 200 250 340 490 650 810 1100 1200 1600 2000 2300 Ordering code composition see below B41044A7477M* B41044A7687M* B41044A7108M* B41044A7158M* B41044A7228M* B41044A7338M* B41044A6224M* B41044A6474M* B41044A6105M* B41044A6225M* B41044A6335M* B41044A6475M* B41044A6106M* B41044A6226M* B41044A6336M* B41044A6476M* B41044A6107M* B41044A6157M* B41044A6227M* B41044A6337M* B41044A6477M* B41044A6687M* B41044A6108M* B41044A6158M* B41044A6228M* Composition of ordering code * = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and 18 x 25 18 x mm Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 40 B41044 Low impedance & high ripple current 105 °C Technical data and ordering codes B41044 CR 120 Hz Case dimensions 20 °C VR = 63 V DC 5 x 11 5 x 11 5 x 11 10 x 16 10 x 20 10 x 25 16 x 20 16 x 25 1000 VR = 100 V DC 5 x 11 5 x 11 5 x 11 10 x 16 16 x 25 18 x 40 Zmax 100 kHz 20 °C IAC,R 100 kHz 105 °C mA 64 76 111 190 233 328 456 610 809 1036 1411 1843 1967 52 64 76 128 224 319 417 570 762 1048 1404 1980 Ordering code composition see below B41044A8335M* B41044A8475M* B41044A8106M* B41044A8226M* B41044A8336M* B41044A8476M* B41044A8107M* B41044A8157M* B41044A8227M* B41044A8337M* B41044A8477M* B41044A8687M* B41044A8108M* B41044A9225M* B41044A9335M* B41044A9475M* B41044A9106M* B41044A9226M* B41044A9336M* B41044A9476M* B41044A9107M* B41044A9157M* B41044A9227M* B41044A9337M* B41044A9477M* Composition of ordering code * = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and 18 x 25 18 x mm Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 40 B43044 Low impedance & high ripple current 105 °C Technical data and ordering codes B43044 CR 120 Hz Case dimensions 20 °C VR = 160 V DC 10 x 20 10 x 20 16 x 25 VR = 200 V DC 10 x 20 16 x 25 18 x 25 VR = 250 V DC 10 x 20 16 x 25 18 x 40 Zmax 100 kHz 20 °C IAC,R 100 kHz 105 °C mA 440 565 725 950 1280 1300 1700 440 590 780 950 1280 1500 1700 300 480 630 1000 1400 1450 1485 Ordering code composition see below B43044A1226M* B43044A1336M* B43044A1476M* B43044A1686M* B43044A1107M* B43044A1157M* B43044A1227M* B43044A1337M* B43044A2226M* B43044A2336M* B43044A2476M* B43044A2686M* B43044A2107M* B43044A2157M* B43044A2227M* B43044F2106M* B43044F2226M* B43044F2336M* B43044F2476M* B43044F2686M* B43044F2107M* B43044F2157M* B43044F2227M* Composition of ordering code * = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and 18 x 25 18 x mm Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 40 B43044 Low impedance & high ripple current 105 °C Technical data and ordering codes B43044 CR 120 Hz Case dimensions 20 °C VR = 350 V DC 10 x 20 16 x 20 16 x 25 VR = 400 V DC 10 x 20 16 x 25 16 x 25 18 x 40 VR = 450 V DC 10 x 20 16 x 25 Zmax 100 kHz 20 °C IAC,R 100 kHz 105 °C mA 180 270 600 700 1100 1170 180 300 600 700 1100 1250 150 200 315 570 620 900 980 Ordering code composition see below B43044A4106M* B43044A4226M* B43044A4336M* B43044A4476M* B43044A4686M* B43044A4107M* B43044A9106M* B43044A9226M* B43044A9336M* B43044A9476M* B43044A9686M* B43044A9107M* B43044A5335M* B43044A5475M* B43044A5106M* B43044A5226M* B43044A5336M* B43044A5476M* B43044A5686M* Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and 18 x 25 18 x mm Please read Cautions and warnings and Important notes at the end of this document. Page 14 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Useful life depending on ambient temperature TA under ripple current operating conditions1 VR 100 V DC d = 5 mm Useful life depending on ambient temperature TA under ripple current operating conditions1 VR 100 V DC d = 8 mm 1 Refer to chapter "General technical information, Calculation of useful life" for an explanation on how to interpret the useful life graphs. Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Useful life depending on ambient temperature TA under ripple current operating conditions2 VR 100 V DC d 10 mm Useful life depending on ambient temperature TA under ripple current operating conditions2 VR > 100 V DC 2 Refer to chapter "General technical information, Calculation of useful life" for an explanation on how to interpret the useful life graphs. Please read Cautions and warnings and Important notes at the end of this document. Page 16 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Frequency factor of permissible ripple current IAC versus frequency f B41044 Frequency factor of permissible ripple current IAC versus frequency f B43044 Please read Cautions and warnings and Important notes at the end of this document. Page 17 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Taping, packing and lead configurations Taping Single-ended capacitors are available taped in Ammo pack from diameter 4 to 18 mm as follows Lead spacing F = mm d = 4 5 mm Lead spacing F = mm d = 4 mm Lead spacing F = mm d = 8 mm Lead spacing F = mm d = 4 mm Lead spacing F = mm d = 16 18 mm . Lead spacing mm d = 4 5 mm Last 3 digits of ordering code 016 Dimensions in mm W0 W1 W2 P min. max. max. Please read Cautions and warnings and Important notes at the end of this document. Page 18 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Lead spacing mm d = 4 mm Last 3 digits of ordering code 007 Dimensions in mm W W0 W1 W2 H0 P P0 P1 I1 Tolerrance min. max. max. max. Lead spacing mm d = 8 mm Last 3 digits of ordering code 006 Dimensions in mm W0 W1 W2 P Tolerance min. max. max. max. Leads can also run straight through the taping area. Taping is available up to dimensions d x l = 8 x 15 mm. Please read Cautions and warnings and Important notes at the end of this document. Page 19 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Lead spacing mm d = 4 8 mm Last 3 digits of ordering code 008 Lead spacing mm d = 10 mm Last 3 digits of ordering code 008 Dimensions in mm W W0 W1 W2 H0 P Tolerance min. max. max. max. Taping is available up to dimensions d x l = 10 x mm and x 25 mm. Taping is not available for d x l = 8 x 20 mm. Please read Cautions and warnings and Important notes at the end of this document. Page 20 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Lead spacing mm d = 16 mm Last 3 digits of ordering code 009 Dimensions in mm W0 W1 W2 P Tolerance min. max. max. Taping is available up to dimensions d x l = 16 x mm and 18 x mm. Please read Cautions and warnings and Important notes at the end of this document. Page 21 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Cut or kinked leads Single-ended capacitors are available with cut or kinked leads. Other lead configurations also available upon request. Cut leads Chapter A Available for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088, B43827, B43828. Last 3 digits of ordering code 002 Case size d x l mm 4 x7 5 x7 5 x 11 x 7 x 11 8 x7 8 x 8 x 15 8 x 20 10 x 10 x 16 10 x 20 10 x 25 10 x Dimensions mm a Case size d x l mm x 16 x 20 x 25 x 40 16 x 20 16 x 25 16 x 16 x 16 x 40 18 x 20 18 x 25 18 x 18 x 18 x 40 Dimensions mm a Please read Cautions and warnings and Important notes at the end of this document. Page 22 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Cut leads Chapter B Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896. Last 3 digits of ordering code 002 With stand-off rubber seal With flat rubber seal Case size d x l mm 10 x 10 x 16 10 x 20 x 20 x 25 16 x 20 16 x 25 16 x 16 x 18 x 20 18 x 25 18 x 18 x 35 18 x 40 Dimensions mm a Please read Cautions and warnings and Important notes at the end of this document. Page 23 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Kinked leads Chapter A Available for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088, B43827, B43828. Last 3 digits of ordering code 001 Case size d x l mm 4 x7 5 x7 5 x 11 x 7 x 11 8 x7 8 x 8 x 15 8 x 20 10 x 10 x 16 10 x 20 10 x 25 10 x Dimensions mm a Case size d x l mm x 16 x 20 x 25 x 40 16 x 20 16 x 25 16 x 16 x 16 x 40 18 x 20 18 x 25 18 x 18 x 18 x 40 Dimensions mm a Please read Cautions and warnings and Important notes at the end of this document. Page 24 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Kinked leads Chapter B Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896. Last 3 digits of ordering code 001 With stand-off rubber seal With flat rubber seal Case size d x l mm 10 x 20 x 20 x 25 16 x 20 16 x 25 16 x 16 x 18 x 20 18 x 25 18 x 18 x 35 18 x 40 Dimensions mm a Please read Cautions and warnings and Important notes at the end of this document. Page 25 of 40 B41044, B43044 Low impedance & high ripple current 105 °C These lead configurations ensure correct placement of the capacitor on the PCB with regard to polarity. PAPR leads are available for diameters from 10 mm up to 18 mm. There are three configurations available Crimped leads, J leads, bent 90° leads Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896. Crimped leads Last 3 digits of ordering code 003 With stand-off rubber seal With flat rubber seal Suggestion for PCB hole diameter Case size d x l mm 16 x 20 16 x 25 16 x 16 x 18 x 20 18 x 25 18 x 18 x 35 18 x 40 Dimensions mm Please read Cautions and warnings and Important notes at the end of this document. Page 26 of 40 B41044, B43044 Low impedance & high ripple current 105 °C J leads Last 3 digits of ordering code 004 Suggestion for PCB hole diameter Case size d x l mm 10 x 10 x 16 10 x 20 x 20 x 25 16 x 20 16 x 25 16 x 16 x 18 x 20 18 x 25 18 x 18 x 35 Dimensions mm Please read Cautions and warnings and Important notes at the end of this document. Page 27 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Bent 90° leads for horizontal mounting pinning Last 3 digits of ordering code 012 Case size d x l mm 16 x 20 16 x 25 16 x 16 x 18 x 20 18 x 25 18 x 18 x 35 18 x 40 Dimensions mm Bent leads for diameter mm available upon request. Please read Cautions and warnings and Important notes at the end of this document. Page 28 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Packing units and box dimensions Ammo pack Valid for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088, B43827, B43828. Case size dxl mm 4x7 5x7 5 x 11 x 7 x 11 8x7 8 x 8 x 15 10 x 10 x 16 10 x 20 x 20 x 25 16 x 25 16 x 18 x 20 18 x 25 18 x Dimensions mm Amax 330 Bmax 50 Cmax 196 330 50 226 330 50 226 330 50 286 330 50 286 330 50 246 330 50 246 330 50 246 330 50 196 330 54 196 330 58 196 341 60 272 341 65 272 320 65 270 315 65 275 315 65 275 315 65 275 315 65 275 Packing units pcs. 2000 1000 500 300 250 Please read Cautions and warnings and Important notes at the end of this document. Page 29 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Ammo pack Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896. Case size dxl mm 8 x 10 x 10 x 16 10 x 20 x 20 x 25 16 x 20 16 x 25 16 x 18 x 20 18 x 25 18 x Dimensions mm Amax 345 4 x7 5 x7 5 x 11 x 7 x 11 8 x7 8 x 8 x 15 8 x 20 10 x 10 x 16 10 x 20 10 x 25 x 16 x 20 x 25 x 40 16 x 20 16 x 25 16 x 16 x 16 x 40 The last three digits of the complete ordering code state the lead configuration Standard, bulk pcs. 10000 7500 5000 2500 2000 1500 2000 1500 1000 750 500 375 250 000 Taped, Kinked leads, Ammo pack bulk pcs. pcs. 2000 15000 2000 10000 2000 10000 2000 10000 2000 5000 1000 5000 1000 4000 1000 2500 2000 2500 2000 1500 1250 1000 Code F mm d mm 001 16 18 Cut leads, bulk pcs. 15000 10000 5000 4000 2500 2000 2500 2000 1500 1250 1000 500 750 500 375 002 Please read Cautions and warnings and Important notes at the end of this document. Page 31 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Overview of packing units and code numbers for case sizes 18 x 20 18 x 40 Case size dxl mm 18 x 20 18 x 25 18 x 18 x 18 x 40 The last three digits of the complete ordering code state the lead configuration Standard, bulk pcs. 250 000 Taped, Ammo pack pcs. Code F mm d mm 16 18 Kinked leads, bulk pcs. 100 001 Cut leads, bulk pcs. 100 002 Please read Cautions and warnings and Important notes at the end of this document. Page 32 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Overview of packing units and code numbers for case sizes 8 x 16 x Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896. Case size dxl mm 8 x 10 x 10 x 16 10 x 20 x 20 x 25 x 30 x 35 x 40 16 x 20 16 x 25 16 x 16 x The last three digits of the complete ordering code state the lead configuration Standard, bulk pcs. 1000 500 350 250 200 175 250 200 100 000 Taped, Ammo pack pcs. 1000 Code F mm d mm 006 008 5 009 Kinked leads, bulk pcs. 500 350 500 200 250 100 001 PAPR Cut Crimped J leads, Bent 90° leads, leads, blister leads, bulk blister blister pcs. pcs. pcs. pcs. 1000 1000 200 120 200 120 250 344 344 120 100 150 002 003 004 012 1 Available upon request Please read Cautions and warnings and Important notes at the end of this document. Page 33 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Overview of packing units and code numbers for case sizes 18 x 20 18 x 40 Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896. Case size dxl mm 18 x 20 18 x 25 18 x 18 x 35 18 x 40 The last three digits of the complete ordering code state the lead configuration Standard, bulk pcs. 175 150 100 125 000 Taped, Ammo pack pcs. 250 Code F mm d mm 009 Kinked leads, bulk pcs. 175 150 100 001 PAPR Cut Crimped J leads, Bent 90° leads, leads, blister leads, bulk blister blister pcs. pcs. pcs. pcs. 175 200 200 120 150 200 200 120 100 150 150 120 100 150 100 120 002 003 004 012 Please read Cautions and warnings and Important notes at the end of this document. Page 34 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Cautions and warnings Personal safety The electrolytes used by EPCOS have not only been optimized with a view to the intended application, but also with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide DMF or dimethyl acetamide DMAC . Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They contain flame-retarding substances which will quickly extinguish any flame that may have been ignited. As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce operating electrolytes. However, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no safe substitute materials are currently known. However, the amount of dangerous materials used in our products has been limited to an absolute minimum. Nevertheless, the following rules should be observed when handling aluminum electrolytic capacitors: Any escaping electrolyte should not come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected parts immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water. Please read Cautions and warnings and Important notes at the end of this document. Page 35 of 40 B41044, B43044 Low impedance & high ripple current 105 °C Product safety The table below summarizes the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of chapter "General technical information". Topic Polarity Mounting position of screwterminal capacitors Mounting of single-ended capacitors Robustness of terminals Soldering Safety information Reference

PDF Datasheet Preview

Aluminum electrolytic capacitors

Single-ended capacitors

Series/Type Date:

B41044, B43044 December 2010

The following products presented in this data sheet are being withdrawn.
Ordering Code

Substitute Product

B41044A8227M000

Date of Withdrawal
2012-04-13

Deadline Last Orders
2012-07-13

Last Shipments 2012-10-13

For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at

EPCOS AG Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited.

Single-ended capacitors Low impedance & high ripple current 105 °C

B41044, B43044

Long-life grade capacitors for professional applications

Power supplies

RoHS-compatible High CV product Low impedance at high frequencies High reliability Useful life of 5000 h at 105 °C

Construction

Radial leads Aluminum case, fully insulated Charge-discharge proof Minus pole marking on the insulating sleeve Case with safety vent from diameter 8 mm

Delivery mode

Bulk Taped, Ammo pack Cut see chapter "Single-ended Taping, packing and lead configurations, Cut leads Chapter A " Kinked see chapter "Single-ended Taping, packing and lead configurations, Kinked leads Chapter A "

Refer to chapter "Single-ended capacitors Taping, packing and lead configurations" for further details.

Specifications and characteristics in brief

Series

B41044

B43044

Rated voltage VR
100 V DC
160 450 V DC

Surge voltage VS

VR 250 V DC VR at room temperature

VR > 250 V DC VR at room temperature

Rated capacitance CR 15000 µF

Capacitance tolerance ±20% M

Dissipation factor max. 20 °C, 120 Hz

For capacitance higher than 1000 µF add for every increase of 1000 µF.
10 16 25 35 50 63 100 160 350
250 450

Please read Cautions and warnings and Important notes at the end of this document.

Page 2 of 40

B41044, B43044 Low impedance & high ripple current 105 °C

Series Leakage current Ileak

B41044 VR 100 V DC
Technical data and ordering codes B41044

CR 120 Hz

Case dimensions
20 °C

VR = V DC
5 x 11
5 x 11
5 x 11
5 x 11
1000
1500
10 x 20
2200
3300
4700
16 x 25
6800
16 x 25
10000
15000

VR = 10 V DC
22 33 47 100 150 220 330 470
5 x 11 5 x 11 5 x 11 5 x 11 x 11 x 11 8 x 8 x

Zmax 100 kHz 20 °C

IAC,R 100 kHz 105 °C mA
180 280 450 660 1100 1400 2100 2600 3000
180 280 450
Ordering code composition see below

B41044A2226M*** B41044A2336M*** B41044A2476M*** B41044A2107M*** B41044A2157M*** B41044A2227M*** B41044A2337M*** B41044A2477M*** B41044A2687M*** B41044A2108M*** B41044A2158M*** B41044A2228M*** B41044A2338M*** B41044A2478M*** B41044A2688M*** B41044A2109M*** B41044A2159M***

B41044A3226M*** B41044A3336M*** B41044A3476M*** B41044A3107M*** B41044A3157M*** B41044A3227M*** B41044A3337M*** B41044A3477M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and
18 x 25 18 x mm

Please read Cautions and warnings and Important notes at the end of this document.

Page 8 of 40

B41044 Low impedance & high ripple current 105 °C
Technical data and ordering codes B41044

CR 120 Hz

Case dimensions
20 °C

VR = 10 V DC
1000
10 x 16
1500
10 x 20
2200
3300
4700
16 x 25
6800
10000

VR = 16 V DC
5 x 11
5 x 11
5 x 11
5 x 11
10 x 16
1000
10 x 20
1500
2200
3300
16 x 25
4700
6800

Zmax 100 kHz 20 °C

IAC,R 100 kHz 105 °C mA
660 850 1100 1400 1700 2100 2600 3000
180 280 450 660 850 1100 1400 1700 2100 2600 3000
Ordering code composition see below

B41044A3687M*** B41044A3108M*** B41044A3158M*** B41044A3228M*** B41044A3338M*** B41044A3478M*** B41044A3688M*** B41044A3109M***

B41044A4106M*** B41044A4226M*** B41044A4336M*** B41044A4476M*** B41044A4107M*** B41044A4157M*** B41044A4227M*** B41044A4337M*** B41044A4477M*** B41044A4687M*** B41044A4108M*** B41044A4158M*** B41044A4228M*** B41044A4338M*** B41044A4478M*** B41044A4688M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and
18 x 25 18 x mm

Please read Cautions and warnings and Important notes at the end of this document.

Page 9 of 40

B41044 Low impedance & high ripple current 105 °C
Technical data and ordering codes B41044

CR 120 Hz

Case dimensions
20 °C

VR = 25 V DC
5 x 11
5 x 11
5 x 11
5 x 11
5 x 11
10 x 16
10 x 20
1000
1500
16 x 20
2200
16 x 25
3300
4700

VR = 35 V DC
5 x 11
5 x 11
5 x 11
5 x 11
10 x 16

Zmax 100 kHz 20 °C

IAC,R 100 kHz 105 °C mA
180 280 450 660 850 1100 1400 2100 2600 3000
180 280 450 660 850
Ordering code composition see below

B41044A5475M*** B41044A5106M*** B41044A5226M*** B41044A5336M*** B41044A5476M*** B41044A5107M*** B41044A5157M*** B41044A5227M*** B41044A5337M*** B41044A5477M*** B41044A5687M*** B41044A5108M*** B41044A5158M*** B41044A5228M*** B41044A5338M*** B41044A5478M***

B41044A7475M*** B41044A7106M*** B41044A7226M*** B41044A7336M*** B41044A7476M*** B41044A7107M*** B41044A7157M*** B41044A7227M*** B41044A7337M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and
18 x 25 18 x mm

Please read Cautions and warnings and Important notes at the end of this document.

Page 10 of 40

B41044 Low impedance & high ripple current 105 °C
Technical data and ordering codes B41044

CR 120 Hz

Case dimensions
20 °C

VR = 35 V DC
10 x 20
1000
1500
16 x 25
2200
3300

VR = 50 V DC
5 x 11
5 x 11
5 x 11
5 x 11
5 x 11
5 x 11
5 x 11
5 x 11
10 x 16
10 x 20
1000
16 x 25
1500
2200

Zmax 100 kHz 20 °C

IAC,R 100 kHz 105 °C mA
1100 1400 1700 2100 2600 3000
18 25 40 55 65 90 120 150 200 250 340 490 650 810 1100 1200 1600 2000 2300
Ordering code composition see below

B41044A7477M*** B41044A7687M*** B41044A7108M*** B41044A7158M*** B41044A7228M*** B41044A7338M***

B41044A6224M*** B41044A6474M*** B41044A6105M*** B41044A6225M*** B41044A6335M*** B41044A6475M*** B41044A6106M*** B41044A6226M*** B41044A6336M*** B41044A6476M*** B41044A6107M*** B41044A6157M*** B41044A6227M*** B41044A6337M*** B41044A6477M*** B41044A6687M*** B41044A6108M*** B41044A6158M*** B41044A6228M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and
18 x 25 18 x mm

Please read Cautions and warnings and Important notes at the end of this document.

Page 11 of 40

B41044 Low impedance & high ripple current 105 °C
Technical data and ordering codes B41044

CR 120 Hz

Case dimensions
20 °C

VR = 63 V DC
5 x 11
5 x 11
5 x 11
10 x 16
10 x 20
10 x 25
16 x 20
16 x 25
1000

VR = 100 V DC
5 x 11
5 x 11
5 x 11
10 x 16
16 x 25
18 x 40

Zmax 100 kHz 20 °C

IAC,R 100 kHz 105 °C mA
64 76 111 190 233 328 456 610 809 1036 1411 1843 1967
52 64 76 128 224 319 417 570 762 1048 1404 1980
Ordering code composition see below

B41044A8335M*** B41044A8475M*** B41044A8106M*** B41044A8226M*** B41044A8336M*** B41044A8476M*** B41044A8107M*** B41044A8157M*** B41044A8227M*** B41044A8337M*** B41044A8477M*** B41044A8687M*** B41044A8108M***

B41044A9225M*** B41044A9335M*** B41044A9475M*** B41044A9106M*** B41044A9226M*** B41044A9336M*** B41044A9476M*** B41044A9107M*** B41044A9157M*** B41044A9227M*** B41044A9337M*** B41044A9477M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and
18 x 25 18 x mm

Please read Cautions and warnings and Important notes at the end of this document.

Page 12 of 40

B43044 Low impedance & high ripple current 105 °C
Technical data and ordering codes B43044

CR 120 Hz

Case dimensions
20 °C

VR = 160 V DC
10 x 20
10 x 20
16 x 25

VR = 200 V DC
10 x 20
16 x 25
18 x 25

VR = 250 V DC
10 x 20
16 x 25
18 x 40

Zmax 100 kHz 20 °C

IAC,R 100 kHz 105 °C mA
440 565 725 950 1280 1300 1700
440 590 780 950 1280 1500 1700
300 480 630 1000 1400 1450 1485
Ordering code composition see below

B43044A1226M*** B43044A1336M*** B43044A1476M*** B43044A1686M*** B43044A1107M*** B43044A1157M*** B43044A1227M*** B43044A1337M***

B43044A2226M*** B43044A2336M*** B43044A2476M*** B43044A2686M*** B43044A2107M*** B43044A2157M*** B43044A2227M***

B43044F2106M*** B43044F2226M*** B43044F2336M*** B43044F2476M*** B43044F2686M*** B43044F2107M*** B43044F2157M*** B43044F2227M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and
18 x 25 18 x mm

Please read Cautions and warnings and Important notes at the end of this document.

Page 13 of 40

B43044 Low impedance & high ripple current 105 °C
Technical data and ordering codes B43044

CR 120 Hz

Case dimensions
20 °C

VR = 350 V DC
10 x 20
16 x 20
16 x 25

VR = 400 V DC
10 x 20
16 x 25
16 x 25
18 x 40

VR = 450 V DC
10 x 20
16 x 25

Zmax 100 kHz 20 °C

IAC,R 100 kHz 105 °C mA
180 270 600 700 1100 1170
180 300 600 700 1100 1250
150 200 315 570 620 900 980
Ordering code composition see below

B43044A4106M*** B43044A4226M*** B43044A4336M*** B43044A4476M*** B43044A4686M*** B43044A4107M***

B43044A9106M*** B43044A9226M*** B43044A9336M*** B43044A9476M*** B43044A9686M*** B43044A9107M***

B43044A5335M*** B43044A5475M*** B43044A5106M*** B43044A5226M*** B43044A5336M*** B43044A5476M*** B43044A5686M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 007 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 006 = for taped leads, Ammo pack, lead spacing F = mm for 8 mm 008 = for taped leads, Ammo pack, lead spacing F = mm for 5 mm 009 = for taped leads, Ammo pack, lead spacing F = mm for d x l = 16 x 20 16 x mm and
18 x 25 18 x mm

Please read Cautions and warnings and Important notes at the end of this document.

Page 14 of 40

B41044, B43044 Low impedance & high ripple current 105 °C Useful life depending on ambient temperature TA under ripple current operating conditions1 VR 100 V DC d = 5 mm

Useful life depending on ambient temperature TA under ripple current operating conditions1 VR 100 V DC d = 8 mm
1 Refer to chapter "General technical information, Calculation of useful life" for an explanation on how to interpret the useful life graphs.

Please read Cautions and warnings and Important notes at the end of this document.

Page 15 of 40

B41044, B43044 Low impedance & high ripple current 105 °C Useful life depending on ambient temperature TA under ripple current operating conditions2 VR 100 V DC d 10 mm

Useful life depending on ambient temperature TA under ripple current operating conditions2 VR > 100 V DC
2 Refer to chapter "General technical information, Calculation of useful life" for an explanation on how to interpret the useful life graphs.

Please read Cautions and warnings and Important notes at the end of this document.

Page 16 of 40

B41044, B43044 Low impedance & high ripple current 105 °C Frequency factor of permissible ripple current IAC versus frequency f B41044

Frequency factor of permissible ripple current IAC versus frequency f B43044

Please read Cautions and warnings and Important notes at the end of this document.

Page 17 of 40

B41044, B43044 Low impedance & high ripple current 105 °C

Taping, packing and lead configurations

Taping

Single-ended capacitors are available taped in Ammo pack from diameter 4 to 18 mm as follows Lead spacing F = mm d = 4 5 mm Lead spacing F = mm d = 4 mm Lead spacing F = mm d = 8 mm Lead spacing F = mm d = 4 mm Lead spacing F = mm d = 16 18 mm .
Lead spacing mm d = 4 5 mm Last 3 digits of ordering code 016

Dimensions in mm

W0 W1 W2 P
min.
max.
max.

Please read Cautions and warnings and Important notes at the end of this document.

Page 18 of 40

B41044, B43044 Low impedance & high ripple current 105 °C
Lead spacing mm d = 4 mm Last 3 digits of ordering code 007

Dimensions in mm

W W0 W1 W2 H0 P

P0 P1 I1

Tolerrance
min.
max.
max.
max.
Lead spacing mm d = 8 mm Last 3 digits of ordering code 006

Dimensions in mm

W0 W1 W2 P

Tolerance
min.
max.
max.
max.

Leads can also run straight through the taping area. Taping is available up to dimensions d x l = 8 x 15 mm.

Please read Cautions and warnings and Important notes at the end of this document.

Page 19 of 40

B41044, B43044 Low impedance & high ripple current 105 °C
Lead spacing mm d = 4 8 mm Last 3 digits of ordering code 008
Lead spacing mm d = 10 mm Last 3 digits of ordering code 008

Dimensions in mm

W W0 W1 W2 H0 P

Tolerance
min. max.
max.
max.

Taping is available up to dimensions d x l = 10 x mm and x 25 mm. Taping is not available for d x l = 8 x 20 mm.

Please read Cautions and warnings and Important notes at the end of this document.

Page 20 of 40

B41044, B43044 Low impedance & high ripple current 105 °C
Lead spacing mm d = 16 mm Last 3 digits of ordering code 009

Dimensions in mm

W0 W1 W2 P

Tolerance
min.
max.
max.

Taping is available up to dimensions d x l = 16 x mm and 18 x mm.

Please read Cautions and warnings and Important notes at the end of this document.

Page 21 of 40

B41044, B43044 Low impedance & high ripple current 105 °C

Cut or kinked leads Single-ended capacitors are available with cut or kinked leads. Other lead configurations also available upon request.
Cut leads Chapter A Available for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088, B43827, B43828. Last 3 digits of ordering code 002

Case size d x l mm
4 x7 5 x7 5 x 11 x 7 x 11 8 x7 8 x 8 x 15 8 x 20 10 x 10 x 16 10 x 20 10 x 25 10 x

Dimensions mm a

Case size d x l mm
x 16 x 20 x 25 x 40 16 x 20 16 x 25 16 x 16 x 16 x 40 18 x 20 18 x 25 18 x 18 x 18 x 40

Dimensions mm a

Please read Cautions and warnings and Important notes at the end of this document.

Page 22 of 40

B41044, B43044 Low impedance & high ripple current 105 °C
Cut leads Chapter B Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896. Last 3 digits of ordering code 002

With stand-off rubber seal With flat rubber seal

Case size d x l mm 10 x 10 x 16 10 x 20 x 20 x 25 16 x 20 16 x 25 16 x 16 x 18 x 20 18 x 25 18 x 18 x 35 18 x 40

Dimensions mm a

Please read Cautions and warnings and Important notes at the end of this document.

Page 23 of 40

B41044, B43044 Low impedance & high ripple current 105 °C
Kinked leads Chapter A Available for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088, B43827, B43828. Last 3 digits of ordering code 001

Case size d x l mm
4 x7 5 x7 5 x 11 x 7 x 11 8 x7 8 x 8 x 15 8 x 20 10 x 10 x 16 10 x 20 10 x 25 10 x

Dimensions mm a

Case size d x l mm
x 16 x 20 x 25 x 40 16 x 20 16 x 25 16 x 16 x 16 x 40 18 x 20 18 x 25 18 x 18 x 18 x 40

Dimensions mm a

Please read Cautions and warnings and Important notes at the end of this document.

Page 24 of 40

B41044, B43044 Low impedance & high ripple current 105 °C
Kinked leads Chapter B Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896. Last 3 digits of ordering code 001

With stand-off rubber seal With flat rubber seal

Case size d x l mm 10 x 20 x 20 x 25 16 x 20 16 x 25 16 x 16 x 18 x 20 18 x 25 18 x 18 x 35 18 x 40

Dimensions mm a

Please read Cautions and warnings and Important notes at the end of this document.

Page 25 of 40

B41044, B43044 Low impedance & high ripple current 105 °C

These lead configurations ensure correct placement of the capacitor on the PCB with regard to polarity. PAPR leads are available for diameters from 10 mm up to 18 mm. There are three configurations available Crimped leads, J leads, bent 90° leads

Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896.
Crimped leads Last 3 digits of ordering code 003

With stand-off rubber seal

With flat rubber seal

Suggestion for PCB hole diameter

Case size d x l mm 16 x 20 16 x 25 16 x 16 x 18 x 20 18 x 25 18 x 18 x 35 18 x 40

Dimensions mm

Please read Cautions and warnings and Important notes at the end of this document.

Page 26 of 40
B41044, B43044 Low impedance & high ripple current 105 °C J leads Last 3 digits of ordering code 004

Suggestion for PCB hole diameter

Case size d x l mm 10 x 10 x 16 10 x 20 x 20 x 25 16 x 20 16 x 25 16 x 16 x 18 x 20 18 x 25 18 x 18 x 35

Dimensions mm

Please read Cautions and warnings and Important notes at the end of this document.

Page 27 of 40

B41044, B43044 Low impedance & high ripple current 105 °C
Bent 90° leads for horizontal mounting pinning Last 3 digits of ordering code 012

Case size d x l mm 16 x 20 16 x 25 16 x 16 x 18 x 20 18 x 25 18 x 18 x 35 18 x 40

Dimensions mm

Bent leads for diameter mm available upon request.

Please read Cautions and warnings and Important notes at the end of this document.

Page 28 of 40

B41044, B43044 Low impedance & high ripple current 105 °C

Packing units and box dimensions

Ammo pack Valid for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088, B43827, B43828.

Case size dxl mm 4x7 5x7 5 x 11 x 7 x 11 8x7 8 x 8 x 15 10 x 10 x 16 10 x 20 x 20 x 25 16 x 25 16 x 18 x 20 18 x 25 18 x

Dimensions mm

Amax 330

Bmax 50

Cmax 196
330 50 226
330 50 226
330 50 286
330 50 286
330 50 246
330 50 246
330 50 246
330 50 196
330 54 196
330 58 196
341 60 272
341 65 272
320 65 270
315 65 275
315 65 275
315 65 275
315 65 275

Packing units pcs. 2000 1000
500 300 250

Please read Cautions and warnings and Important notes at the end of this document.

Page 29 of 40

B41044, B43044 Low impedance & high ripple current 105 °C

Ammo pack

Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896.

Case size dxl mm 8 x 10 x 10 x 16 10 x 20 x 20 x 25 16 x 20 16 x 25 16 x 18 x 20 18 x 25 18 x

Dimensions mm

Amax 345
4 x7 5 x7 5 x 11 x 7 x 11 8 x7 8 x 8 x 15 8 x 20 10 x 10 x 16 10 x 20 10 x 25 x 16 x 20 x 25 x 40 16 x 20 16 x 25 16 x 16 x 16 x 40 The last three digits of the complete ordering code state the lead configuration

Standard, bulk pcs. 10000
7500 5000 2500 2000 1500 2000 1500 1000
750 500 375 250 000

Taped,

Kinked leads,

Ammo pack
bulk
pcs.
pcs.
2000
15000
2000
10000
2000
10000
2000
10000
2000
5000
1000
5000
1000
4000
1000
2500
2000
2500
2000
1500
1250
1000

Code F mm d mm 001
16 18

Cut leads, bulk pcs. 15000 10000
5000 4000 2500 2000 2500 2000 1500 1250 1000
500 750 500 375 002

Please read Cautions and warnings and Important notes at the end of this document.

Page 31 of 40

B41044, B43044 Low impedance & high ripple current 105 °C

Overview of packing units and code numbers for case sizes 18 x 20 18 x 40
Case size dxl mm 18 x 20 18 x 25 18 x 18 x 18 x 40 The last three digits of the complete ordering code state the lead configuration

Standard, bulk pcs.
250 000

Taped, Ammo pack
pcs.

Code F mm d mm
16 18

Kinked leads, bulk pcs.
100 001

Cut leads, bulk pcs.
100 002

Please read Cautions and warnings and Important notes at the end of this document.

Page 32 of 40

B41044, B43044 Low impedance & high ripple current 105 °C

Overview of packing units and code numbers for case sizes 8 x 16 x

Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896.

Case size dxl
mm 8 x 10 x 10 x 16 10 x 20 x 20 x 25 x 30 x 35 x 40 16 x 20 16 x 25 16 x 16 x The last three digits of the complete ordering code state the lead configuration

Standard, bulk pcs. 1000 500 350 250 200 175 250 200 100 000

Taped, Ammo pack
pcs.
1000

Code F mm d mm
006 008 5 009

Kinked leads, bulk pcs. 500 350 500 200 250 100 001

PAPR

Cut Crimped J leads, Bent 90°
leads, leads, blister leads,
bulk blister
blister
pcs. pcs.
pcs. pcs.
1000
1000
200 120
200 120
250 344
344 120
100 150
002 003
004 012
1 Available upon request

Please read Cautions and warnings and Important notes at the end of this document.

Page 33 of 40

B41044, B43044 Low impedance & high ripple current 105 °C

Overview of packing units and code numbers for case sizes 18 x 20 18 x 40

Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824, B42851, B43866, B43867, B43890, B43896.

Case size dxl
mm 18 x 20 18 x 25 18 x 18 x 35 18 x 40 The last three digits of the complete ordering code state the lead configuration

Standard, bulk pcs. 175 150 100 125 000

Taped, Ammo pack
pcs. 250 Code F mm d mm 009

Kinked leads, bulk pcs. 175 150 100 001

PAPR

Cut Crimped J leads, Bent 90°
leads, leads, blister leads,
bulk blister
blister
pcs. pcs.
pcs. pcs.
175 200
200 120
150 200
200 120
100 150
150 120
100 150
100 120
002 003
004 012

Please read Cautions and warnings and Important notes at the end of this document.

Page 34 of 40

B41044, B43044 Low impedance & high ripple current 105 °C

Cautions and warnings

Personal safety The electrolytes used by EPCOS have not only been optimized with a view to the intended application, but also with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide DMF or dimethyl acetamide DMAC .

Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They contain flame-retarding substances which will quickly extinguish any flame that may have been ignited.

As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce operating electrolytes. However, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no safe substitute materials are currently known. However, the amount of dangerous materials used in our products has been limited to an absolute minimum. Nevertheless, the following rules should be observed when handling aluminum electrolytic capacitors:

Any escaping electrolyte should not come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected parts immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water.

Please read Cautions and warnings and Important notes at the end of this document.

Page 35 of 40

B41044, B43044 Low impedance & high ripple current 105 °C

Product safety

The table below summarizes the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of chapter "General technical information".

Topic Polarity

Mounting position of screwterminal capacitors Mounting of single-ended capacitors

Robustness of terminals

Soldering

Safety information

Reference

More datasheets: B41044A2226M | B41044A2227M | B41044A2228M | B41044A2337M | B41044A2338M | B41044A2336M | B41044A2158M | B41044A5338M | B41044A5475M | B41044A5476M

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived B41044A5477M Datasheet file may be downloaded here without warranties.

Datasheet ID: B41044A5477M 511413