APRIL

APRIL Datasheet

april [electric imp]

Part	Datasheet
APRIL	APRIL (pdf)

PDF Datasheet Preview
april [electric imp] April Development Board April is a very simple board with the minimum required components for a working impee. Project Files Schematics Gerber Files Bill of Materials Altium Source Files 3/15/2013 Power Power can be supplied using a USB-Mini-B cable from a USB Charger or standard USB Port, though the data lines are not connected to anything. Optionally, a battery connector can be soldered to the battery pads, P+, P-. April can operate from any DC voltage from to 17 Volts, and tolerates voltages down to -12 Volts. This is helpful for any application with removable batteries where they may be inserted backwards by the user. You may select between USB power and battery power by placing a shunt on the power select header. Please note that April does not have any circuitry for charging a battery and you should never short USB power to the battery pack. April uses the TI TPS62172 DC/DC Buck Power supply for 3.3V. It can provide an additional to any boards connected to April, however if your application requires more than it must have it's own supply. The 3 pin jumper allows selection of the DC input source jumper between the middle pin and the side labeled USB for USB power, and the other way for battery pack power soldering the input leads onto the P+ and P- pads . Signals All of the signals from the imp come out to a header. For descriptions of pin of function see the Imp Pin Mux. Card Detect If your application requires the card detect signal, it must be pulled up by soldering an 0402 resistor R3 or on an external board.. The signal is connected to GND whenever a card is present in the slot, so we recommend using a 100kΩ or higher resistor to save power. april.txt • Last modified 2012/10/03 00:53 by hugo Except where otherwise noted, content on this wiki is licensed under the following license CC Attribution-Share Alike Unported 3/15/2013

PDF Datasheet Preview

april [electric imp]

April Development Board

April is a very simple board with the minimum required components for a working impee.

Project Files

Schematics Gerber Files Bill of Materials Altium Source Files
3/15/2013

Power

Power can be supplied using a USB-Mini-B cable from a USB Charger or standard USB Port, though the data lines are not connected to anything. Optionally, a battery connector can be soldered to the battery pads, P+, P-. April can operate from any DC voltage from to 17 Volts, and tolerates voltages down to -12 Volts. This is helpful for any application with removable batteries where they may be inserted backwards by the user. You may select between USB power and battery power by placing a shunt on the power select header. Please note that April does not have any circuitry for charging a battery and you should never short USB power to the battery pack. April uses the TI TPS62172 DC/DC Buck Power supply for 3.3V. It can provide an additional to any boards connected to April, however if your application requires more than it must have it's own supply. The 3 pin jumper allows selection of the DC input source jumper between the middle pin and the side labeled USB for USB power, and the other way for battery pack power soldering the input leads onto the P+ and P- pads .

Signals

All of the signals from the imp come out to a header. For descriptions of pin of function see the Imp Pin Mux.

Card Detect

If your application requires the card detect signal, it must be pulled up by soldering an 0402 resistor R3 or on an external board.. The signal is connected to GND whenever a card is present in the slot, so we recommend using a 100kΩ or higher resistor to save power.
april.txt
• Last modified 2012/10/03 00:53 by hugo

Except where otherwise noted, content on this wiki is licensed under the following license CC Attribution-Share Alike Unported
3/15/2013

More datasheets: 1140-151K | 1140-121K | 1140-271K | 1140-820K | 1140-681K | Q48SK12033NRFA | Q48SK12033NRFH | T0053418699N | 2540103 | 2570103

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived APRIL Datasheet file may be downloaded here without warranties.

Datasheet ID: APRIL 510934