Electronic Circuit Breaker ESS20
Part | Datasheet |
---|---|
![]() |
ESS20-003-DC24V-2A (pdf) |
Related Parts | Information |
---|---|
![]() |
ESS20-003-DC24V-0.5A |
![]() |
ESS20-003-DC24V-10A |
![]() |
ESS20-003-DC24V-1A/2A |
![]() |
ESS20-003-DC24V-4A |
![]() |
ESS20-003-DC24V-1A |
![]() |
ESS20-003-DC24V-6A |
![]() |
ESS20-003-DC24V-8A |
![]() |
ESS20-003-DC24V-3A/6A |
PDF Datasheet Preview |
---|
Electronic Circuit Breaker ESS20 Electronic circuit breaker type ESS20 is designed to ensure selective disconnection of individual loads in systems which are powered by a DC 24 V switch-mode power supply. DC 24 V power supplies, which are widely used in industry today, will shut down the output in the event of an overload with the result that one faulty load in the system can lead to complete disconnection of all loads. As well as an unidentified failure this also means stoppage of the whole system. Through selective disconnection the ESS20 responds much faster to overload or short circuit conditions than the switch-mode power supply. This is achieved by a combination of active current limitation and well-proven circuit breaker technology including physical isolation. The ESS20 limits the highest possible current to times the set rated current of the circuit breaker. Thus it is possible to switch on even capacitive loads or lamp loads, but they are disconnected only in the event of an overload or short circuit. ESS20 Technical data Tambient = 25°C, operating voltage UB = DC 24 V For optimal adjustment to the application conditions the current rating of the ESS20 can be selected by a switch 3 A or 6 A . Failure and status indication are provided by a bicolour LED and an integral signal contact. Operating data Operating voltage UB Current rating IN Power consumption DC 24 V 18 32 V 3 A or 6 A selected by means of a switch typically 13 mA The ESS20 features a width of only mm and can be plugged into the E-T-A power distribution socket Module 17plus, ensuring ease of installation and saving space in control cabinets. Trip current bimetal Status indication by means of typ. 1A only in the event of a failure, before physical isolation bicolour LED GREEN unit is ON, power-MOSFET is switched on ORANGE in the event of overload or short circuit until physical isolation LED not lighted push button in OFF position potential-free signal contact changeover contact OFF-position of push button q Selective load protection with physical isolation in the event of a fault q All types of loads can be connected DC motors etc. on request q Active current limitation times rated current for safe Load circuit internal bimetal fail-safe element trips, push button moves into OFF position connection of capacitive loads and on overload/short circuit q Electronic trip characteristic Load output Power-MOSFET switching output high side switch q One unit for two current ratings 3 A and 6 A selectable Max. data of load DC 24 V / 6 A resistive, inductive, q Manual ON/OFF button push-push actuation q Clear status and failure indication q Width per unit only mm capacitive, lamp load with side-by-side mounting 6A at Tamb = +40°C and 100% ON duty 5A at Tamb = +50°C and 100% ON duty q Plug-in mounting utilising power distribution system Module 17plus Voltage drop at IN typically. 130 mV / 3 A typically 260 mV / 6 A Approvals VDE, UL approval pending Overload disconnection typically x IN x IN Short-circuit current IK typically x IN max. 2 x IN / active current limitation Trip time see time/current characteristics for physical isolation typ. 5 sec at Iload > x IN for electronic disconnection typ. 5 sec 100 ms at Iload > x IN Ordering information Fault indication, signal output Fault indications potential-free auxiliary contact change-over SC-SO / SC-SI simultaneously with physical isolation max. DC 30 V / A, min. 10 V / 10 mA Signal output blue push button in ON position signal contact SC-SO is closed SC-SI is open blue push button in OFF position signal contact SC-SO is open SC-SI is closed Visual indication LED lighted after typ. 50 ms in ORANGE until physical isolation Type No. ESS20 Electronic Circuit Breaker for DC 24 V applications Version 00 standard Control input 0 without signal contact 3 with signal contact changeover contact Input voltage DC 24 V rated voltage DC 24 V Current rating 3 A/6 A selectable switch ESS20 - 00 3 - DC 24 V - 3 A/6 A ordering example recommended type General data Ambient temperature °C without condensation, see EN 60204-1 Storage temperature Backup fuse for ESS20 not required because of the integral redundant fail-safe element thermal circuit breaker in Vorb. Basic circuit diagram Blade terminals mm to DIN 46244-A6, 3-0,8 Housing material plastics material Mounting of housing plug-in mounting utilising power distribution system Module 17plus control Vibration Degree of protection 3 g, test to IEC 68-2-6 test Fc Housing IP 20 DIN 40050, Terminals IP 00 DIN 40050 LINE + DC 24 V Emission EN 50081-1 EMC directive, CE logo Susceptibility EN 61000-6-2 current short circuit / measurement overload Insulation co-ordination kV/2 ON / OFF IEC 60934 re-inforced insulation in operating area Dielectric strength operating area see dimensions test voltage AC 1000 V status indication green / orange installation area test voltage AC 500 V load circuit-signal contact test voltage AC 500 V 3A 6A rated current IN Rsense Insulation resistance >100 DC 500 V OFF condition [LINE + LOAD + ] Dimensions W x H x D x 105 x 60 mm Mass Ordering information Voltage rating without ESS20 : AC 433 V DC 65 V Current rating without ESS20 LINE feed 1 LOAD output 2 Reference potential GND 11 10 A Individual signal 12 1 A with ESS20 0,5 A Group signal / 13-14 1 A with ESS20 0,5 A 17PLUS-Q02-00 Module 17plus, middle part, two-way 17PLUS-Q00-LR-EES one each left- and right-side terminal block for ESS20 17PLUS-QA0-LR-EES one each left- and right-side terminal block with screw terminal for busbar for ESS20 Internal resistance values without ESS20 LINE-LOAD 1-2 Group signal 13-14 per module 5 8 per pole +5 for each additional module Busbar for power distribution insulated busbar blue or red : Imax 32 A non-insulated busbar: Imax 50 A The non-insulated busbar, too, meets brush contact safety standards when fitted. Dielectric strength of Module 17plus without ESS20 between main circuits without busbar 1,500 V main circuit to auxiliary circuit: 1,500 V between auxiliary circuits: 1,500 V Mass Module 17plus middle part terminal blocks pair approx. 85 g approx. 30 g ¤ Germany 0 91 87 10-0 - USA 847 827-7600 - UK 01296 420336 - Issue E ESS20 - Accessories Module 17plus Dimensions |
More datasheets: AD9841AJSTZ | 43-01036 | 43-01032 | 43-01033 | 43-01034 | ESS20-003-DC24V-0.5A | ESS20-003-DC24V-10A | ESS20-003-DC24V-1A/2A | ESS20-003-DC24V-4A | ESS20-003-DC24V-1A |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ESS20-003-DC24V-2A Datasheet file may be downloaded here without warranties.