2-4100-P10-0.05A

2-4100-P10-0.05A Datasheet

Type No. 2-4100 threadneck panel mounting

Part	Datasheet
2-4100-P10-0.05A	2-4100-P10-0.05A (pdf)

PDF Datasheet Preview
Thermal Overcurrent Circuit Breaker Single pole thermal circuit breaker with push-to-reset, tease-free, tripfree, snap action mechanism R-type TO CBE to EN Options include an additional unprotected circuit tap -A3 and -KF housing particularly suited to high humidity and other damp conditions. Designed for threadneck panel mounting. Approved to CBE standard EN 60934 IEC Motors, transformers, solenoids, hand tools, appliances. Ordering information Type No. 2-4100 threadneck panel mounting hardware bulk shipped Terminal design L10 solder terminals P10 blade terminals A6.3-0.8 mm QC P50 blade terminals A4.8-0.8 mm QC Shunt terminal optional A3 shunt terminal 3 A max. load Current ratings A 2-4100 - L10 - - - 5 A ordering example The exact part number required can be built up from the table of choices shown above. Ordering references for optional features should be omitted if not required. Standard current ratings and typical internal resistance values Currrent rating A 1 Internal resistance Ω 322 125 101 25 11 Current rating A 2 3 4 5 6 7 8 10 Internal resistance Ω < < < < Approvals Technical data For further details please see chapter Technical Information Voltage rating AC 250 V DC 28 V Current rating range Typical life AC 250 V / DC 28 V DC 28 V A Ambient temperature 2,000 operations at 2 x IN, resistive 1,000 operations at 2 x IN, inductive °C °F Insulation co-ordination IEC 60664 and 60664 A rated impulse pollution withstand voltage degree reinforced insulation in operating area Dielectric strength IEC 60664 and 60664 A test voltage operating area AC 3,000 V Insulation resistance > 100 MΩ DC 500 V Interrupting capacity Icn Interrupting capacity UL 1077 IN A 5A 10 x IN 8 x IN 6 x IN UN AC 250 V AC 250 V 200 A 1,000 A Degree of protection IEC 60529/DIN 40050 operating area IP40 terminal area IP00 Vibration 10 g 57-500 Hz ± mm 10-57 Hz , to IEC 60068-2-6, test Fc, 10 frequency cycles/axis Shock 25 g 11 ms to IEC 60068-2-27, test Ea Corrosion 96 hours at 5 % salt mist, to IEC 60068-2-11, test Ka All dimensions without tolerances are for reference only. In the interest of improved design, performance and cost effectiveness the right to make changes in these specifications without notice is reserved.Product markings may not be exactly as the ordering codes. Errors and omissions excepted. 1 - 95 Thermal Overcurrent Circuit Breaker Dimensions tightening torque 1 Nm 3/8-27 UNS-2A D-shaped threadneck blade terminals DIN46244-A6.3-0.8 QC mounting hole SW 14 current rating in A Installation drawing Trip time in seconds Internal connection diagram Typical time/current characteristics at +23 °C/+73.4 °F 10000 1000 100 10 operating area 6 max mounting area Terminal design -L10 -P10-A3 -P50 blade terminals DIN46244-4.8-0.8 QC max. 7 max blade terminals DIN46244-6.3-0.8 QC 4 6 8 10 times rated current The time/current characteristic curve depends on the ambient temperature prevailing. In order to eliminate nuisance tripping, please multiply the circuit breaker current ratings by the derating factor shown below. See also section 9 Technical information. Ambient temperature °F °C -4 +14 +32 +104 +122 +140 -20 -10 0 +23 +40 +50 +60 Derating factor Accessories Water splash cover, transparent Y 300 538 01, bonded to knurled nut Y 300 628 01 X 200 799 01 IP64 3/8-27 UNS-2B Water splash cover, transparent bonded to special knurled nut X 200 798 02 IP64 Hex nut with splash cover, black X 210 739 01 IP64 Water splash cover, transparent with hex nut X 201 296 03 IP64 This is a metric design and millimeter dimensions take precedence mm inch 1 - 96 3/8-27 UNS-2B 3/8-27 UNS-2B Issue B

PDF Datasheet Preview

Thermal Overcurrent Circuit Breaker

Single pole thermal circuit breaker with push-to-reset, tease-free, tripfree, snap action mechanism R-type TO CBE to EN Options include an additional unprotected circuit tap -A3 and -KF housing particularly suited to high humidity and other damp conditions. Designed for threadneck panel mounting. Approved to CBE standard EN 60934 IEC

Motors, transformers, solenoids, hand tools, appliances.
Ordering information

Type No. 2-4100 threadneck panel mounting
hardware bulk shipped Terminal design L10 solder terminals P10 blade terminals A6.3-0.8 mm QC P50 blade terminals A4.8-0.8 mm QC

Shunt terminal optional A3 shunt terminal 3 A max. load

Current ratings A
2-4100 - L10 - - - 5 A ordering example
The exact part number required can be built up from the table of choices shown above. Ordering references for optional features should be omitted if not required.

Standard current ratings and typical internal resistance values

Currrent rating A 1

Internal resistance Ω 322 125 101 25 11

Current rating A 2 3 4 5 6 7 8 10

Internal resistance Ω < < < <

Approvals

Technical data

For further details please see chapter Technical Information

Voltage rating

AC 250 V DC 28 V

Current rating range

Typical life AC 250 V / DC 28 V DC 28 V A

Ambient temperature
2,000 operations at 2 x IN, resistive 1,000 operations at 2 x IN, inductive
°C °F

Insulation co-ordination IEC 60664 and 60664 A
rated impulse
pollution
withstand voltage degree
reinforced insulation in operating area

Dielectric strength

IEC 60664 and 60664 A test voltage
operating area

AC 3,000 V

Insulation resistance
> 100 MΩ DC 500 V

Interrupting capacity Icn

Interrupting capacity UL 1077

IN A 5A
10 x IN 8 x IN 6 x IN

UN AC 250 V AC 250 V
200 A 1,000 A

Degree of protection IEC 60529/DIN 40050
operating area IP40 terminal area IP00

Vibration
10 g 57-500 Hz ± mm 10-57 Hz , to IEC 60068-2-6, test Fc, 10 frequency cycles/axis

Shock
25 g 11 ms to IEC 60068-2-27, test Ea

Corrosion
96 hours at 5 % salt mist, to IEC 60068-2-11, test Ka
All dimensions without tolerances are for reference only. In the interest of improved design, performance and cost effectiveness the right to make changes in these specifications without notice is reserved.Product markings may not be exactly as the ordering codes. Errors and omissions excepted.
1 - 95

Thermal Overcurrent Circuit Breaker

Dimensions
tightening torque 1 Nm 3/8-27 UNS-2A

D-shaped threadneck
blade terminals DIN46244-A6.3-0.8 QC
mounting hole

SW 14 current rating in A

Installation drawing

Trip time in seconds

Internal connection diagram

Typical time/current characteristics at +23 °C/+73.4 °F
10000 1000 100 10
operating area
6 max
mounting area

Terminal design
-L10
-P10-A3
-P50
blade terminals DIN46244-4.8-0.8 QC
max. 7 max
blade terminals DIN46244-6.3-0.8 QC
4 6 8 10
times rated current

The time/current characteristic curve depends on the ambient temperature prevailing. In order to eliminate nuisance tripping, please multiply the circuit breaker current ratings by the derating factor shown below. See also section 9 Technical information.

Ambient temperature °F °C
-4 +14 +32 +104 +122 +140 -20 -10 0 +23 +40 +50 +60

Derating factor

Accessories

Water splash cover, transparent Y 300 538 01, bonded to knurled nut Y 300 628 01 X 200 799 01 IP64
3/8-27 UNS-2B

Water splash cover, transparent bonded to special knurled nut X 200 798 02 IP64

Hex nut with splash cover, black X 210 739 01 IP64 Water splash cover, transparent with hex nut X 201 296 03 IP64

This is a metric design and millimeter dimensions take precedence mm inch
1 - 96
3/8-27 UNS-2B
3/8-27 UNS-2B

Issue B

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 2-4100-P10-0.05A Datasheet file may be downloaded here without warranties.

Datasheet ID: 2-4100-P10-0.05A 510411