5151040

5151040 Datasheet

515-1040

Part	Datasheet
5151040	5151040 (pdf)

PDF Datasheet Preview
4mm Round OptopipeTM Optical Light Pipe, 4 Array, Panel Mounted 515-1040 Recommended DIRECTION OF LIGHT RIBS TYP 3 PLCS DIFFUSED FRONT SURFACE TYP REF 3 PLCS 4 PLCS 3 PLCS MicroLED SMT LEDs for use with 515-1040 PART NO. PAGE # 597-3xx1-2xx 1-21 FRONT PANEL C.L LED 597-3xx1-5xx 597-77x1-2xx 597-77x1-5xx 1-30 1-23 & 1-24 1-31 MAJOR DIA Ø TYP 4 PLCS TOP SURFACE OF LED Dimensions in mm [inches] RECOMMENDED PANEL HOLE SIZE Ø • High transmissivity polycarbonate material • UL94V-0 compliance • ESD protection circuit isolation from front panel • Wide viewing angle • Arrays reduce insertion costs • Secures to panel by press-fit LED Data For absolute maximum ratings and other electrical and optical data on the recommended LEDs, refer to LED data sheets. Operating/Storage Temperature to +100°C Dialight Optopipe Light Pipe Description This Optopipe is mounted through the rear of the panel and is retained by press fit. The light pipe is not attached to the PCB at any point but floats above it. The diffused light emitting surfaces appear bright and uniformly illuminated. The recommended light sources are Dialight's 597 Series PLCC-2 or PLCC-4 Type SMT LEDs. The light source’s emitting surface should be located no more than or 0.5mm from the Optopipe . The SMT LEDs are mounted in a straight line under the rear of the part on a mm pitch. The light pipe material is water clear transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index. Dialight can provide custom Optopipe solutions for your applications. Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL 732 919-3119 • FAX 732 751-5778 2-17

PDF Datasheet Preview

4mm Round

OptopipeTM

Optical Light Pipe, 4 Array, Panel Mounted
515-1040

Recommended

DIRECTION OF LIGHT RIBS

TYP 3 PLCS

DIFFUSED FRONT SURFACE

TYP REF
3 PLCS 4 PLCS
3 PLCS

MicroLED SMT LEDs
for use with 515-1040

PART NO. PAGE #
597-3xx1-2xx
1-21

FRONT PANEL

C.L LED
597-3xx1-5xx 597-77x1-2xx 597-77x1-5xx
1-30 1-23 & 1-24
1-31

MAJOR DIA
Ø TYP 4 PLCS

TOP SURFACE OF LED

Dimensions in mm [inches]

RECOMMENDED PANEL HOLE SIZE Ø
• High transmissivity polycarbonate material
• UL94V-0 compliance
• ESD protection circuit isolation from front panel
• Wide viewing angle
• Arrays reduce insertion costs
• Secures to panel by press-fit

LED Data

For absolute maximum ratings and other electrical and optical data on the recommended LEDs, refer to LED data sheets.

Operating/Storage Temperature
to +100°C

Dialight Optopipe Light Pipe Description

This Optopipe is mounted through the rear of the panel and is retained by press fit. The light pipe is not attached to the PCB at any point but floats above it. The diffused light emitting surfaces appear bright and uniformly illuminated. The recommended light sources are Dialight's 597 Series PLCC-2 or PLCC-4 Type SMT LEDs. The light source’s emitting surface should be located no more than or 0.5mm from the Optopipe . The SMT LEDs are mounted in a straight line under the rear of the part on a mm pitch. The light pipe material is water clear transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index.

Dialight can provide custom Optopipe solutions for your applications.

Dialight Corporation
• 1501 Route 34 South
• Farmingdale, NJ 07727
• TEL 732 919-3119
• FAX 732 751-5778 2-17

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 5151040 Datasheet file may be downloaded here without warranties.

Datasheet ID: 5151040 509300