5151023

5151023 Datasheet

515-1023-803

Part	Datasheet
5151023	5151023 (pdf)

PDF Datasheet Preview
3mm Square OptopipeTM Optical Light Pipe, Quad High 515-1023-803 LIGHTSHIELDS 2 PLCS NOTE C.L. of LED Direction of Light Ø ± RECOMMENDED PIN HOLES AND SOLDER PAD LAYOUT FOR SUGGESTED MicroLED LEDs COMPONENT SIDE OF PRINTED CIRCUIT BOARD REF. Recommended MicroLED SMT LEDs 2 for use with 515-1023-803 COLOR PAGE # 597-3001-1xx 1-19 597-3111-1xx DIA] TYP. 597-3211-1xx 2 PLACES 597-3301-1xx AlGaAs Red Orange Green 1-19 1-19 1-19 597-3401-1xx Yellow 1-19 597-7701-1xx Red/Green 1-20 597-7721-1xx Yellow/Green 1-20 NOTE designed for post-reflow PC board insertion. 597-7731-1xx Red/Yellow 1-20 Dimensions in mm [inches] • High transmissivity polycarbonate material • UL94V-0 compliance • ESD protection circuit isolation from front panel • Wide viewing angle • Arrays reduce insertion costs • Allows quad level SMT indicators • Secures to PCB by press-fit LED Data For absolute maximum ratings and other electrical and optical data on the recommended LEDs, refer to LED data sheets. Operating/Storage Temperature to +100°C Dialight Optopipe Light Pipe Description This Optopipe has a relatively low vertical height considering the number of light pipe elements. The element’s square emitting surfaces are vertically spaced from the PCB to the first element, and then between each of the other elements. This Optopipe is held in place by 2 press-fit pins on the bottom of the device. The wide base offers added stability to the installed part. The light pipe is not attached to the panel at any point, but protrudes through holes in the panel. This Optopipe was specifically designed to accept Dialight’s 597 Series Type 1210 LEDs. The light pipe material is water clear transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index. Dialight can provide custom Optopipe solutions for your applications.

PDF Datasheet Preview

3mm Square

OptopipeTM

Optical Light Pipe, Quad High
515-1023-803

LIGHTSHIELDS 2 PLCS

NOTE C.L. of LED

Direction of Light
Ø ±

RECOMMENDED PIN HOLES AND SOLDER PAD LAYOUT FOR SUGGESTED MicroLED LEDs

COMPONENT SIDE OF PRINTED CIRCUIT BOARD

REF.

Recommended MicroLED SMT LEDs
2 for use with 515-1023-803

COLOR PAGE #
597-3001-1xx
1-19
597-3111-1xx

DIA] TYP.
597-3211-1xx
2 PLACES
597-3301-1xx

AlGaAs Red Orange Green
1-19 1-19 1-19
597-3401-1xx

Yellow
1-19
597-7701-1xx Red/Green
1-20
597-7721-1xx Yellow/Green 1-20

NOTE designed for post-reflow PC board insertion.
597-7731-1xx Red/Yellow
1-20

Dimensions in mm [inches]
• High transmissivity polycarbonate material
• UL94V-0 compliance
• ESD protection circuit isolation from front panel
• Wide viewing angle
• Arrays reduce insertion costs
• Allows quad level SMT indicators
• Secures to PCB by press-fit

LED Data

For absolute maximum ratings and other electrical and optical data on the recommended LEDs, refer to LED data sheets.

Operating/Storage Temperature
to +100°C

Dialight Optopipe Light Pipe Description

This Optopipe has a relatively low vertical height considering the number of light pipe elements. The element’s square emitting surfaces are vertically spaced from the PCB to the first element, and then between each of the other elements. This Optopipe is held in place by 2 press-fit pins on the bottom of the device. The wide base offers added stability to the installed part. The light pipe is not attached to the panel at any point, but protrudes through holes in the panel. This Optopipe was specifically designed to accept Dialight’s 597 Series Type 1210 LEDs. The light pipe material is water clear transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index.

Dialight can provide custom Optopipe solutions for your applications.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 5151023 Datasheet file may be downloaded here without warranties.

Datasheet ID: 5151023 509299