SKU:TEL0092 WiFi Bee-ESP8266 Wirelss module
Part | Datasheet |
---|---|
![]() |
TEL0092 (pdf) |
PDF Datasheet Preview |
---|
Page 1 of 32 SKU:TEL0092 WiFi Bee-ESP8266 Wirelss module Contents 1 Introduction 2 Specifications 3 Pin out 4 Tutorials How to Use ? 1 Connect AP 2 WiFi Bee-ESP8266 SKU:TEL0092 TCP_Client_Single 3 TCP_Client_multi 4 TCP_Pure_Data_Mode 5 Server mode * Problem Shooting Update Firmware 5 Application 6 AT command How to enter AT mode 7 Related link 8 More Introduction Wifi Bee-ESP8266 is a Serial-to-WIFI module using XBEE design in a compact size, compatible with XBEE expansion base, applicable to a variety of 3.3V single-chip system. It can be used for Arduino, wireless data transfer, remote control. On-board switch can be used to easily select the Startup module or Upgrade firmware. Page 2 of 32 ESP8266 has a powerful on-chip processing and storage capacity, built-in 32-bit processor, built-in Lwip protocol stack. Support AP+STA mode co-exist. And you could configure various parameters via AT commands. Specifications Wi-Fi Direct P2P ,soft-AP Built-in TCP/IP protocol stack Built-in low-power 32-bit CPU can work as an application processor Support WPA WPA2/WPA2-PSK encryption Support UART interface Support for TTL serial port to wireless application Working voltage 3.3V power <240Ma Wireless standard IEEE802.11b/g/n Frequency GHz Pin out Tutorials These stuffs are needed 1 Software Page 3 of 32 ESP_Flasher Arduino IDE CoolTerm NetAssist 2 Hardware DFRduino UNO R3 Xbee USB adapter FTDI ready IO Expansion Shield for Arduino V6 USB Cable A-B for Arduino Mini USB cable How to Use ? 1 Connect AP 1 Download the ESP8266 library and unzip it to 2 Insert the expansion shield on UNO, and plug ESP8266 in the socket on the expansion shield. 3 Note the switch “RUN/Prog” at “Prog” side “BOOT/UART” at "BOOT" side 4 Wire adapter to the expansion shield TX- PIN10, RX- PIN11, GND - GND; Page 4 of 32 5 Open the sketch "Connect AP", and modify the wifi AP ssid and password of yours; Page 5 of 32 6 Upload the sketch 7 Trun the switch of the expansion shield “RUN/Prog” to “Run” side 8 Use software "CoolTerm" to monitor if the AP connection is done. Configure as the follow picture Page 6 of 32 Page 7 of 32 2 TCP_Client_Single 1 Pull the switch"RUN/Prog" to "Prog" 2 Check the Ip address of your computer, we will use it as the Server Ip address; Page 8 of 32 3 Open sample sketch "TCP_Client_Single", write your wifi's ssid, password , Server Ip address, port; Page 9 of 32 4 Open the software"TCP/IP Net Assistant V3.8", configure as follow, and click Connect to monitor the PC doing as Server; Page 10 of 32 5 Upload the modified sketch, and then pull the switch"RUN/Prog" to "RUN" 6 Open "CoolTerm" and monitor the if the AP connection was good; Page 11 of 32 |
More datasheets: B59154C1130B151 | B59084B1120A151 | B59603B1120B157 | B59022S1120A51 | B59069B1080B151 | B59042B1120B151 | B59024S1120A151 | B59023S1120A70 | B59184B1120A151 | A-2004-0-2-LP/S-R |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived TEL0092 Datasheet file may be downloaded here without warranties.