SEN0220

SEN0220 Datasheet

Infrared CO2 Sensor SKU SEN0220

Part	Datasheet
SEN0220	SEN0220 (pdf)

PDF Datasheet Preview
Infrared CO2 Sensor SKU SEN0220 Introduction DFRobot released its latest wide range infrared CO2 sensor, which effective range is up to 0~50000ppm. This sensor is based on non-dispersive infrared NDIR technology and has good selectivity and oxygen-free dependency. It integrates temperature compensation and support UART communication mode. Most importantly, the product is easy to use it is compatible with all types of microcontrollers with UART port, like Arduino, Raspberry Pi and other microcontrollers. Besides, it has a long service life, up to 5 years! In addition, this UART Infrared CO2 Sensor is a high-performance sensor that combines technology of mature infrared absorption gas detection with precision optical circuit design as well as sophisticated circuit design. It has characteristics such as wide range detection, high sensitivity, high resolution, low power consumption, fast response, anti-water vapor interference, no poisoning, high stability and long life. It can be widely used in HVAC refrigeration and indoor air quality monitoring, industrial process and safety monitoring, agricultural and animal husbandry production process monitoring, etc.. • Wide Range • High Sensitivity • Low power consumption • Excellent stability • Temperature compensation • Excellent linear output • High cycle life • Anti-water vapor interference • No poisoning • Need 5V power supply, even you are using a 3.3V microcontroller, like Genuino 101/ Raspberry Pi or anything else. Specification • Gas Detection Carbon Dioxide CO2 • Operating Voltage ~ 5.5V DC • Average Current <85mA • Output Signal UART/PWM/Analog output the last two has not been developed • Measuring Range 0 ~ 50000ppm • Accuracy ± 50ppm + 5% reading • Preheating Time 3min • Response Time T90 < 30s • Operating Temperature 0 ~ 50 • Operating Humidity 0 ~ 95% RH no condensation • Service Life >5 years • Board Dimension 21 * mm/ * inches • Weight 42 g Board Overview SEN0220 CO2 Sensor Num 1 2 3 4 5 Label RX TX GND VCC Detector connection Description RX TX GND VCC Detector connection Tutorial Upload the code to Arduino Uno, open the serial monitor to check the CO2 concentration. NOTE The CO2 concentration during the preheating time in the serial monitor is not accurate, just ignore the result in the first 3 minutes Preheating Time . Requirements • Hardware DFRduino UNO x 1 • Gravity UART Infrared CO2 Sensor DuPont cables • Software Arduino IDE Click to Download Arduino IDE from Connection Diagram SEN0220_Connection Sample Code * Infrared CO2 Sensor 0-50000ppm Wide Range * * The follow example is used to detect CO2 concentration. * * V1.0 * 2016-6-6 * GNU Lesser General Public License. * See for details. * All above must be included in any redistribution * #include <SoftwareSerial.h> SoftwareSerial mySerial 10, 11 // RX, TX unsigned char hexdata[9] = //Read the gas density command /Don't change the order void setup Serial.begin 9600 while !Serial mySerial.begin 9600 ; void loop mySerial.write hexdata,9 delay 500 ; for int i=0,j=0;i<9;i++ if mySerial.available >0 long hi,lo,CO2 int ch=mySerial.read ; hi=ch //High concentration lo=ch //Low concentration if i==8 CO2=hi*256+lo //CO2 concentration Serial.print "CO2 concentration " ; Serial.print CO2 ; Serial.println "ppm" ; Expected Results Open your IDE serial monitor and wait for about 3 minutes preheat process , then you'll see the finial data. Indoor Temperature 25 5-3-17

PDF Datasheet Preview

Infrared CO2 Sensor SKU SEN0220

Introduction

DFRobot released its latest wide range infrared CO2 sensor, which effective range is up to 0~50000ppm. This sensor is based on non-dispersive infrared NDIR technology and has good selectivity and oxygen-free dependency. It integrates temperature compensation and support UART communication mode. Most importantly, the product is easy to use it is compatible with all types of microcontrollers with UART port, like Arduino, Raspberry Pi and other microcontrollers. Besides, it has a long service life, up to 5 years! In addition, this UART Infrared CO2 Sensor is a high-performance sensor that combines technology of mature infrared absorption gas detection with precision optical circuit design as well as sophisticated circuit design. It has characteristics such as wide range detection, high sensitivity, high resolution, low power consumption, fast response, anti-water vapor interference, no poisoning, high stability and long life. It can be widely used in HVAC refrigeration and indoor air quality monitoring, industrial process and safety monitoring, agricultural and animal husbandry production process monitoring, etc..
• Wide Range
• High Sensitivity
• Low power consumption
• Excellent stability
• Temperature compensation
• Excellent linear output
• High cycle life
• Anti-water vapor interference
• No poisoning
• Need 5V power supply, even you are using a 3.3V microcontroller, like Genuino 101/ Raspberry Pi
or anything else.

Specification
• Gas Detection Carbon Dioxide CO2
• Operating Voltage ~ 5.5V DC
• Average Current <85mA
• Output Signal UART/PWM/Analog output the last two has not been developed
• Measuring Range 0 ~ 50000ppm
• Accuracy ± 50ppm + 5% reading
• Preheating Time 3min
• Response Time T90 < 30s
• Operating Temperature 0 ~ 50
• Operating Humidity 0 ~ 95% RH no condensation
• Service Life >5 years
• Board Dimension 21 * mm/ * inches
• Weight 42 g

Board Overview

SEN0220 CO2 Sensor

Num 1 2 3 4 5

Label RX TX GND VCC Detector connection

Description RX TX GND VCC Detector connection

Tutorial

Upload the code to Arduino Uno, open the serial monitor to check the CO2 concentration.

NOTE The CO2 concentration during the preheating time in the serial monitor is not accurate, just ignore the result in the first 3 minutes Preheating Time .

Requirements
• Hardware

DFRduino UNO x 1
• Gravity UART Infrared CO2 Sensor DuPont cables
• Software Arduino IDE Click to Download Arduino IDE from

Connection Diagram

SEN0220_Connection

Sample Code
* Infrared CO2 Sensor 0-50000ppm Wide Range * * The follow example is used to detect CO2 concentration.
* * V1.0 * 2016-6-6
* GNU Lesser General Public License. * See for details. * All above must be included in any redistribution * #include <SoftwareSerial.h> SoftwareSerial mySerial 10, 11 // RX, TX unsigned char hexdata[9] = //Read the gas density command /Don't change the order void setup

Serial.begin 9600 while !Serial
mySerial.begin 9600 ;
void loop mySerial.write hexdata,9 delay 500 ;
for int i=0,j=0;i<9;i++
if mySerial.available >0 long hi,lo,CO2 int ch=mySerial.read ;
hi=ch //High concentration
lo=ch //Low concentration
if i==8

CO2=hi*256+lo //CO2 concentration

Serial.print "CO2 concentration " ;

Serial.print CO2 ;

Serial.println "ppm" ;

Expected Results

Open your IDE serial monitor and wait for about 3 minutes preheat process , then you'll see the finial data. Indoor Temperature 25
5-3-17

More datasheets: 438 | 12-5-438 | 3-5-438 | 1/2-5-438 | 1-5-438 | 12X12-6-438 | 3/4-5-438 | 2-5-438 | 4-5-438 | 6-5-438

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived SEN0220 Datasheet file may be downloaded here without warranties.

Datasheet ID: SEN0220 509118