DFR0327

DFR0327 Datasheet

Arduino Shield for Raspberry Pi 2B and 3B SKU:DFR0327

Part	Datasheet
DFR0327	DFR0327 (pdf)

PDF Datasheet Preview
Arduino Shield for Raspberry Pi 2B and 3B SKU:DFR0327 Contents • 1 Introduction • 2 Specification • 3 Features • 4 Raspberry Pi B+ Meet Arduino Shield Pinout Feature Introduction Diagram • 5 Get Started with Raspberry Pi B+ Meet Arduino Shield Tools Required Software Required Hardware Connection Step by Step tutorial • 6 Program the Arduino shield using Raspberry Pi B+ Software Required Steps • 7 FAQ Introduction What happens when a Pi meets an Arduino? A simple example would be, when building a mobile robot, we use the Raspberry Pi to extend its vision and get a nice tiny monitor. Meanwhile, Arduino handle nicely with the motor driving part and delivers fast responses like obstacle avoidance. Because, without the OS, the response time of rapid changes on the Arduino is much shorter. Also the high performance Pi can deals much easily with wireless communications, imaging and running complex algorithm. Therefore, with the Arduino and Pi together, you get a powerful "brain" and "cerebellum" for your project, at one time. Specification • Onboard Microcontroller ATmega32u4 • Arduino Leonardo Chip • Arduino Compatible pin mapping • Compatible with All arduino standard shield and sensors • System Voltage 5v • Arduino Digital I/O 20 • Arduino Analog I/O 6 • Raspberry Pi B+ GPIO 16 • Raspberry Pi B+ I2C 1 • Raspberry Pi B+ ID_I2C 1 • Raspberry Pi B+ SPI 1 • Raspberry Pi B+ TTL UART 1 • Dimension 88mm x 56mm x 26mm • Integrate with the Xbee socket Available to be connected to Arduino or Raspberry Pi B+ directly either Compatible with BLE Link BT4.0 /Bluetooth Bee BT2.1 and xbee modules • Embeded DS1307 RTC module,which keeps time of the Pi even when the power is off, or the battery removed • Bidirectional logic converter for Raspberry Pi B+ GPIO to convert signal between 3.3v and 5v • 3 pin headers sensor port for Arduino pins and B+ GPIO, directly compatible with hundreds of Arduino sensors and modules,like Relay Module V3.1 for IOT AC control Analog pH Meter Kit for monitoring Water quality of your pool SHT1x Humidity and Temperature Sensor Motion Sensor for security and human detection And so on... • Arduino shield compatible layout makes it possible to extend Arduino shield features for your Pi also, A nice and low cost LCD12864 display 2A Motor Shield for robot building Dual Bipolar Stepper Motor Shield GSM/GPRS and GPS Shield Raspberry Pi B+ Meet Arduino Shield Pinout Fig1 Pi Meet Arduino Pinout NOTE The ID-I2C is an EEPROM interface, which is dedicated to connect to external EEPROM, it will test automatically EEPROM devices attached to it when it starts, is used for configuring GPIO and Linux drivers. In theory, it can be used as an ordinary IIC. Feature Introduction Diagram Fig2 Feature Introduction Get Started with Raspberry Pi B+ Meet Arduino Shield First of all, let's control a sensor by Raspberry Pi directly with Meet Arduino Shield. Note For this tutorial, we assume that you've known the basic knowledge about the Raspberry Pi B+. And more details will be focused on how to extend and use more hardware modules and sensors for your Raspberry pi B+ projects. In this part, we will control the Relay module with Python via Pi's GPIO. Tools Required Raspberry Pi B+ with Ethernet or WIFI connected Raspberry Pi B+ Meet Arduino shield Relay module or and LED module Software Required Python 2 Installed. Setup SSH on Raspberry Pi. If you didn't install python. Please enter the following commands below into LX Terminal via SSH. sudo apt-get update sudo apt-get install python-rpi.gpio Hardware Connection Fig3 Relay CD Step by Step tutorial 1.Plug the Pi Meet Arduino shield to the Raspberry Pi B+, Which connected with the power and Ethernet. 2.Connect the Relay module or LED module to your Pi as the hardware connection shown. 3.Login in your Pi by Putty. Fig4 Login SSH 4.Create a Python example code using nano. nano blink.py import RPi.GPIO as GPIO import time GPIO.setmode GPIO.BCM GPIO.setup 4,GPIO.OUT while True GPIO.output 4,GPIO.HIGH time.sleep 1 GPIO.output 4,GPIO.LOW time.sleep 1 5.Run the python sample by the command below.And Check the effect. PS The module is connected to the GPIO 4 matching the software configuration. python blink.py 6.<Ctrl>+<C> to stop running the python demo. = The switching of the relay module create the noise... Program the Arduino shield using Raspberry Pi B+ In this part, we will share how to program your Arduino using Pi. The steps is quite simple what you need is just installing the Arduino on your Pi and run the remote desktop to test it. Software Required TightVNC Viewer on your PC TightVNC on your Pi Arduino IDE on your Pi To install the TightVNC on your Pi, please check the commands below.

PDF Datasheet Preview

Arduino Shield for Raspberry Pi 2B and 3B SKU:DFR0327

Contents
• 1 Introduction
• 2 Specification
• 3 Features
• 4 Raspberry Pi B+ Meet Arduino Shield Pinout

Feature Introduction Diagram
• 5 Get Started with Raspberry Pi B+ Meet Arduino Shield

Tools Required Software Required Hardware Connection Step by Step tutorial
• 6 Program the Arduino shield using Raspberry Pi B+ Software Required Steps
• 7 FAQ

Introduction

What happens when a Pi meets an Arduino? A simple example would be, when building a mobile robot, we use the Raspberry Pi to extend its vision and get a nice tiny monitor. Meanwhile, Arduino handle nicely with the motor driving part and delivers fast responses like obstacle avoidance. Because, without the OS, the response time of rapid changes on the Arduino is much shorter. Also the high performance Pi can deals much easily with wireless communications, imaging and running complex algorithm. Therefore, with the Arduino and Pi together, you get a powerful "brain" and "cerebellum" for your project, at one time.

Specification
• Onboard Microcontroller ATmega32u4
• Arduino Leonardo Chip
• Arduino Compatible pin mapping
• Compatible with All arduino standard shield and sensors
• System Voltage 5v
• Arduino Digital I/O 20
• Arduino Analog I/O 6
• Raspberry Pi B+ GPIO 16
• Raspberry Pi B+ I2C 1
• Raspberry Pi B+ ID_I2C 1
• Raspberry Pi B+ SPI 1
• Raspberry Pi B+ TTL UART 1
• Dimension 88mm x 56mm x 26mm
• Integrate with the Xbee socket Available to be connected to Arduino or Raspberry Pi B+ directly either Compatible with BLE Link BT4.0 /Bluetooth Bee BT2.1 and xbee modules
• Embeded DS1307 RTC module,which keeps time of the Pi even when the power is off, or the battery removed
• Bidirectional logic converter for Raspberry Pi B+ GPIO to convert signal between 3.3v and 5v
• 3 pin headers sensor port for Arduino pins and B+ GPIO, directly compatible with hundreds of Arduino sensors and modules,like Relay Module V3.1 for IOT AC control Analog pH Meter Kit for monitoring Water quality of your pool SHT1x Humidity and Temperature Sensor Motion Sensor for security and human detection And so on...
• Arduino shield compatible layout makes it possible to extend Arduino shield features for your Pi also, A nice and low cost LCD12864 display 2A Motor Shield for robot building Dual Bipolar Stepper Motor Shield GSM/GPRS and GPS Shield

Raspberry Pi B+ Meet Arduino Shield Pinout

Fig1 Pi Meet Arduino Pinout NOTE The ID-I2C is an EEPROM interface, which is dedicated to connect to external EEPROM, it will test automatically EEPROM devices attached to it when it starts, is used for configuring GPIO and Linux drivers. In theory, it can be used as an ordinary IIC.

Feature Introduction Diagram

Fig2 Feature Introduction

Get Started with Raspberry Pi B+ Meet Arduino Shield

First of all, let's control a sensor by Raspberry Pi directly with Meet Arduino Shield. Note For this tutorial, we assume that you've known the basic knowledge about the Raspberry Pi B+. And more details will be focused on how to extend and use more hardware modules and sensors for your Raspberry pi B+ projects. In this part, we will control the Relay module with Python via Pi's GPIO.

Tools Required

Raspberry Pi B+ with Ethernet or WIFI connected Raspberry Pi B+ Meet Arduino shield Relay module or and LED module

Software Required

Python 2 Installed. Setup SSH on Raspberry Pi.

If you didn't install python. Please enter the following commands below into LX Terminal via SSH. sudo apt-get update sudo apt-get install python-rpi.gpio

Hardware Connection

Fig3 Relay CD

Step by Step tutorial
1.Plug the Pi Meet Arduino shield to the Raspberry Pi B+, Which connected with the power and Ethernet. 2.Connect the Relay module or LED module to your Pi as the hardware connection shown. 3.Login in your Pi by Putty.

Fig4 Login SSH 4.Create a Python example code using nano. nano blink.py import RPi.GPIO as GPIO
import time

GPIO.setmode GPIO.BCM GPIO.setup 4,GPIO.OUT
while True GPIO.output 4,GPIO.HIGH time.sleep 1 GPIO.output 4,GPIO.LOW time.sleep 1
5.Run the python sample by the command below.And Check the effect. PS The module is connected to the GPIO 4 matching the software configuration.
python blink.py
6.<Ctrl>+<C> to stop running the python demo. = The switching of the relay module create the noise...

Program the Arduino shield using Raspberry Pi B+

In this part, we will share how to program your Arduino using Pi. The steps is quite simple what you need is just installing the Arduino on your Pi and run the remote desktop to test it.

Software Required

TightVNC Viewer on your PC TightVNC on your Pi Arduino IDE on your Pi

To install the TightVNC on your Pi, please check the commands below.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived DFR0327 Datasheet file may be downloaded here without warranties.

Datasheet ID: DFR0327 508720