DFR0058

DFR0058 Datasheet

Analog Rotation Sensor V2 SKU DFR0058

Part	Datasheet
DFR0058	DFR0058 (pdf)

PDF Datasheet Preview
Analog Rotation Sensor V2 SKU DFR0058 Contents • 1 Introduction • 2 Specification • 3 Pin Definition • 4 Tutorial Requirements Connection Diagram Sample Code • 5 Dimension Diagram Introduction This V2 Rotation Sensor is arduino compatible multi-ring rotation analog sensor. It is based on multiturn precision potentiometer. It can rotate upto 10 laps. If the sensor input 5V voltage power, then the 5000mV will be divided into 3600 portions 10 laps , when you adjust the rotation of the 3 degrees and then the voltage will have 2mV change, so you can accurately achieve the effect of voltage with small changes. and it is easy to be connected to Arduino or DFRduino with our sensor expansion board. Specification • Arduino compatible • Operating Voltage +3.3-5V DC • Signal Type analog signal • Size 50x22mm • Tnterface Mode Gravity interface PH2.0-3 • Rotation Angle 3600 degrees • Weight 20g Pin Definition Color BLACK RED BLUE Description GND VCC Analog Signal Output Tutorial In this tutorial we rotate the Analog Rotation Sensor V2 to output the analog voltage value in the serial port. Requirements • Hardware UNO x1 Analog Rotation Sensor V2 x1 • Software Arduino IDE V1.6.5 Click to Download Arduino IDE from Connection Diagram Analog Rotation Sensor V2 connection diagram Sample Code const int analogInPin = A0 // Analog input pin that the potentiometer is at tached to const int analogOutPin = 9 // Analog output pin that the LED is attached to int sensorValue = 0 int outputValue = 0; // value read from the pot // value output to the PWM analog out void setup // initialize serial communications at 9600 bps Serial.begin 9600 ; void loop // read the analog in value sensorValue = analogRead analogInPin // map it to the range of the analog out outputValue = map sensorValue, 0, 1023, 0, 255 // change the analog out value analogWrite analogOutPin, outputValue // print the results to the serial monitor Serial.print "sensor = " Serial.print sensorValue output = " Serial.println outputValue // wait 2 milliseconds before the next loop // for the analog-to-digital converter to settle // after the last reading delay 20 ; Dimension Diagram Powered By DFRobot 2008-2017

PDF Datasheet Preview

Analog Rotation Sensor V2 SKU DFR0058

Contents
• 1 Introduction
• 2 Specification
• 3 Pin Definition
• 4 Tutorial

Requirements Connection Diagram Sample Code
• 5 Dimension Diagram

Introduction

This V2 Rotation Sensor is arduino compatible multi-ring rotation analog sensor. It is based on multiturn precision potentiometer. It can rotate upto 10 laps. If the sensor input 5V voltage power, then the 5000mV will be divided into 3600 portions 10 laps , when you adjust the rotation of the 3 degrees and then the voltage will have 2mV change, so you can accurately achieve the effect of voltage with small changes. and it is easy to be connected to Arduino or DFRduino with our sensor expansion board.

Specification
• Arduino compatible
• Operating Voltage +3.3-5V DC
• Signal Type analog signal
• Size 50x22mm
• Tnterface Mode Gravity interface PH2.0-3
• Rotation Angle 3600 degrees
• Weight 20g

Pin Definition

Color BLACK

RED BLUE

Description GND VCC

Analog Signal Output

Tutorial

In this tutorial we rotate the Analog Rotation Sensor V2 to output the analog voltage value in the serial port.

Requirements
• Hardware UNO x1 Analog Rotation Sensor V2 x1
• Software Arduino IDE V1.6.5 Click to Download Arduino IDE from

Connection Diagram

Analog Rotation Sensor V2 connection diagram

Sample Code
const int analogInPin = A0 // Analog input pin that the potentiometer is at tached to const int analogOutPin = 9 // Analog output pin that the LED is attached to
int sensorValue = 0 int outputValue = 0;
// value read from the pot // value output to the PWM analog out
void setup // initialize serial communications at 9600 bps Serial.begin 9600 ;
void loop
// read the analog in value sensorValue = analogRead analogInPin // map it to the range of the analog out outputValue = map sensorValue, 0, 1023, 0, 255 // change the analog out value analogWrite analogOutPin, outputValue // print the results to the serial monitor Serial.print "sensor = " Serial.print sensorValue output = " Serial.println outputValue // wait 2 milliseconds before the next loop // for the analog-to-digital converter to settle // after the last reading delay 20 ;

Dimension Diagram

Powered By DFRobot 2008-2017

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived DFR0058 Datasheet file may be downloaded here without warranties.

Datasheet ID: DFR0058 508624