SK-FM0-100L-S6E1B8
SK-FM0-100L-S6E1B8 Datasheet
This application note describes the starter kit SK-FM0-100L-S6E1B8 and how to use it.
| Part | Datasheet |
|---|---|
SK-FM0-100L-S6E1B8 |
SK-FM0-100L-S6E1B8 (pdf) |
| PDF Datasheet Preview |
|---|
| THIS SPEC IS OBSOLETE Spec No: 002-04393 Spec Title: AN204393 - FM0+ Starter Kit 32-Bit Microcontroller Replaced by 002-05536 FM0+ Starter Kit 32-Bit Microcontroller AN204393 Target Products S6E1B8 Series This application note describes the starter kit SK-FM0-100L-S6E1B8 and how to use it. Contents 1 Document Purpose Definitions, Acronyms, and Abbreviations........1 Document Overview 2 Overview and Features Board Overview Board Features System Block 3 Software Preparation and Installation.......................4 CMSIS-DAP Driver Installation Virtual Communication Port Installation 4 Board Description and Connection Hardware Description Jumpers Description 4Connectors Hardware Connection and IAR Configuration..8 5 Firmware Architecture 11 Firmware Architecture Diagram 11 6 Module Labs Operation 12 Control the RGB LED using Base Timer........12 UART Receive/Send Data with CMSIS-DAP.19 Measure the Potentiometer Analog Voltage 25 Measure Acceleration with KXCJK-1013 Accelerometer 31 Read/Write SD Play Pixie Dust Sound Data...........................47 7 Additional 8 Document 1 Introduction Document Purpose This application note describes the starter kit SK-FM0-100L-S6E1B8 and how to use it. Definitions, Acronyms, and Abbreviations UART Universal Asynchronous Receiver/Transmitter USB Universal Serial Bus LED Light Emitting Diode LDO Low-Drop-Out linear voltage regulator Interface I2S Integrated Interchip Sound Input and Output PDL Peripheral Driver Library FM0+ Starter Kit 32-Bit Microcontroller Document Overview The rest of document is organized like this Section 2 explains Overview and Features Section 3 explains Software Preparation and Installation. Section 4 explains Board Description and Connection. Section 5 explains Firmware Architecture. Section 6 explains Module Labs Operation. Section 7 explains Additional Information 2 Overview and Features Board Overview The SK-FM0-100L-S6E1B8 is a Starter Kit for Cypress S6E1B8 Series microcontrollers. The S6E1B8 Series is highly integrated 32-bit microcontrollers designed for embedded controllers aiming at low power consumption and low cost. This series has the ARM Cortex-M0+ Processor with on-chip Flash memory and SRAM, and consists of peripheral functions such as various timers, ADCs and communication interfaces UART, CSIO, I2C, LIN, I2S, and USB . Figure Board Overview Board Features • Cypress FM0+ S6E1B8 MCU • CMSIS DAP interface • JTAG interface • Free Pins interface • Arduino Shield interface • USB Device Micro type-B • SD card interface • Acceleration Sensor • Potentiometer • Microphone/ Headphone interface • RGB LED • 2 x Push-button System Block Diagram Figure System Block Diagram |
| More datasheets: H3BBH-1036G | H3BBH-2018G | H1BXH-1036M | H3BBH-1406G | H3BWH-6436G | H3AWH-6436G | H3BWH-6418M | H3AAH-6436M | H3BBH-6436M | 423-2ASURC/S400-A8 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived SK-FM0-100L-S6E1B8 Datasheet file may be downloaded here without warranties.