MB95F376LPMC1-G-SNE2

MB95F376LPMC1-G-SNE2 Datasheet


MB95F314E/F314L/F316E/F316L/F318E/F318L MB95F374E/F374L/F376E/F376L/F378E/F378L

Part Datasheet
MB95F376LPMC1-G-SNE2 MB95F376LPMC1-G-SNE2 MB95F376LPMC1-G-SNE2 (pdf)
Related Parts Information
MB95F378EPMC1-G-SNE2 MB95F378EPMC1-G-SNE2 MB95F378EPMC1-G-SNE2
MB95F378LPMC2-G-SNE2 MB95F378LPMC2-G-SNE2 MB95F378LPMC2-G-SNE2
MB95F374LPMC1-G-SNE2 MB95F374LPMC1-G-SNE2 MB95F374LPMC1-G-SNE2
MB95F374EPMC1-G-SNE2 MB95F374EPMC1-G-SNE2 MB95F374EPMC1-G-SNE2
PDF Datasheet Preview
MB95F314E/F314L/F316E/F316L/F318E/F318L MB95F374E/F374L/F376E/F376L/F378E/F378L

New 8FX MB95310L/370L Series 8-bit Microcontrollers

MB95310L/370L is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of this series contain a variety of peripheral resources.

F2MC-8FX CPU core

Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instructions
• Bit manipulation instructions, etc.

Clock

Selectable main clock source Main OSC clock up to MHz, maximum machine clock frequency MHz External clock up to MHz, maximum machine clock frequency MHz Main CR clock MHz 2%, maximum machine clock frequency MHz Main PLL clock up to MHz, maximum machine clock frequency MHz
• Selectable subclock source Sub-OSC clock kHz External clock kHz Sub-CR clock Typ 100 kHz, Min 50 kHz, Max 200 kHz

Timer
• 8/16-bit composite timer
• 8/16-bit PPG
• 16-bit reload timer
• Event counter
• Time-base timer
• Watch prescaler

UART-SIO
• Capable of clock-asynchronous UART serial data transfer and clock-synchronous SIO serial data transfer
• Full duplex double buffer

Built-in wake-up function

External interrupt
• Interrupt by edge detection rising edge, falling edge, and both edges can be selected
• Can be used to wake up the device from different low power consumption standby modes
8/10-bit A/D converter
8-bit or 10-bit resolution can be selected

LCD controller LCDC
• 40 SEG 4 COM
• 32 SEG 4 COM
• Internal divider resistor
• With blinking function

Low power consumption standby modes
• Stop mode
• Sleep mode
• Watch mode
• Time-base timer mode

I/O port
• MB95F314E/F314L/F316E/F316L/F318E/F318L maximum no. of I/O ports 71 General-purpose I/O ports N-ch open drain 3 General-purpose I/O ports CMOS I/O 68
• MB95F374E/F374L/F376E/F376L/F378E/F378L maximum no. of I/O ports 55 General-purpose I/O ports N-ch open drain 3 General-purpose I/O ports CMOS I/O 52

On-chip debug
• 1-wire serial control
• Serial writing supported asynchronous mode

Hardware/software watchdog timer
• Built-in hardware watchdog timer
• Built-in software watchdog timer
• San Jose, CA 95134-1709
• 408-943-2600

MB95310L/370L Series

Low-voltage detection reset circuit
• Built-in low-voltage detector
• Three configurable low-voltage detection levels for generating
reset
• Five configurable low-voltage detection levels for generating
interrupts

Clock supervisor counter

Built-in clock supervisor counter function
Recommended Operating Conditions 42 DC Characteristics 43 AC Characteristics 47 Clock Timing 47 Source Clock/Machine Clock 49 External Reset 52 Power-on Reset 54 Peripheral Input Timing 55 UART/SIO, Serial I/O Timing 56 Low-voltage Detection 58 I2C Timing 60 A/D Converter 65 A/D Converter Electrical Characteristics 65 Notes on Using the A/D Converter 66 Definitions of A/D Converter Terms 67 Flash Memory Program/Erase Characteristics 69 Sample Characteristics 71 Mask Options 79 Ordering Information 80 Package Dimension 80 Major Changes 84

Page 3 of 80

MB95310L/370L Series

Product Line-up
• MB95310L Series Part number

MB95F314E MB95F316E MB95F318E MB95F314L MB95F316L MB95F318L

Parameter

Type

Flash memory product

Clock supervisor counter

It supervises the main clock oscillation.

Flash memory capacity
20 Kbyte
36 Kbyte
60 Kbyte
20 Kbyte
36 Kbyte
60 Kbyte

RAM capacity
496 bytes
1008 bytes
2032 bytes
496 bytes
1008 bytes
2032 bytes

Low-voltage detection reset

Reset input

Dedicated

CPU functions
• Number of basic instructions
• Instruction bit length
• Instruction length
• Data bit length
• Minimum instruction execution time
• Interrupt processing time
136 8 bits 1 to 3 bytes 1, 8 and 16 bits ns machine clock frequency = MHz µs machine clock frequency = MHz

General-purpose I/O
• I/O ports Max
• CMOS I/O
• N-ch open drain
71 68 :3

Time-base timer Interval time ms - s external clock frequency = 4 MHz

Hardware/software watchdog timer



Reset generation cycle Main oscillation clock at 10 MHz 105 ms Min

The sub-CR clock can be used as the source clock of the hardware watchdog timer.

Wild register

It can be used to replace three bytes of data.
Ordering Information

MB95F314EPMC-G-SNE2 MB95F314LPMC-G-SNE2 MB95F316EPMC-G-SNE2 MB95F316LPMC-G-SNE2 MB95F318EPMC-G-SNE2 MB95F318LPMC-G-SNE2

MB95F374EPMC1-G-SNE2 MB95F374LPMC1-G-SNE2 MB95F376EPMC1-G-SNE2 MB95F376LPMC1-G-SNE2 MB95F378EPMC1-G-SNE2 MB95F378LPMC1-G-SNE2

Package
80-pin plastic LQFP FPT-80P-M37
64-pin plastic LQFP FPT-64P-M38

Page 73 of 80

MB95F374EPMC2-G-SNE2 MB95F374LPMC2-G-SNE2 MB95F376EPMC2-G-SNE2 MB95F376LPMC2-G-SNE2 MB95F378EPMC2-G-SNE2 MB95F378LPMC2-G-SNE2

MB95310L/370L Series

Package
64-pin plastic LQFP FPT-64P-M39

Page 74 of 80

MB95310L/370L Series

Package Dimension
80-pin plastic LQFP

FPT-80P-M37

Lead pitch Package width x package length

Lead shape Lead bend direction Sealing method

Mounting height

Weight
mm x mm

Gullwing Normal bend Plastic mold mm MAX
80-pin plastic LQFP FPT-80P-M37
14.00±0.20 .551±.008 SQ *12.00±0.10 .472±.004 SQ

Note 1 * These dimensions do not include resin protrusion. Note 2 Pins width and pins thickness include plating thickness. Note 3 Pins width do not include tie bar cutting remainder.

INDEX

C 2009-2010 FUJITSU SEMICONDUCTOR LIMITED F80037S-c-1-2

Details of "A" part

Mounting height
0~8°

Stand off

Dimensions in mm inches . Note The values in parentheses are reference values.

Page 75 of 80

MB95310L/370L Series
64-pin plastic LQFP FPT-64P-M38

Lead pitch Package width x package length

Lead shape Lead bend direction Sealing method

Mounting height

Weight
mm x mm

Gullwing Normal bend Plastic mold mm MAX
More datasheets: RL65-21/12H | RL65-21/14H | 2830 | FFB20U60STM | 18027 | ACPM-9340-TR2 | ACPM-9340-BLK | ACPM-9340-TR1 | MB95F378EPMC1-G-SNE2 | MB95F378LPMC2-G-SNE2


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MB95F376LPMC1-G-SNE2 Datasheet file may be downloaded here without warranties.

Datasheet ID: MB95F376LPMC1-G-SNE2 508307