MB95F818KPMC-G-UNE2

MB95F818KPMC-G-UNE2 Datasheet

MB95810K Series

Part	Datasheet
MB95F818KPMC-G-UNE2	MB95F818KPMC-G-UNE2 (pdf)

PDF Datasheet Preview
MB95810K Series New 8FX 8-bit Microcontrollers The MB95810K Series is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of these series contain a variety of peripheral resources. • F2MC-8FX CPU core Instruction set optimized for controllers • Multiplication and division instructions • 16-bit arithmetic operations • Bit test branch instructions • Bit manipulation instructions, etc. • Clock Selectable main clock source • Main oscillation clock up to MHz, maximum machine clock frequency MHz • External clock up to MHz, maximum machine clock frequency MHz • Main CR clock 4 MHz 2% • Main CR PLL clock - The main CR PLL clock frequency becomes 8 MHz 2% when the PLL multiplication rate is - The main CR PLL clock frequency becomes 10 MHz 2% when the PLL multiplication rate is - The main CR PLL clock frequency becomes 12 MHz 2% when the PLL multiplication rate is - The main CR PLL clock frequency becomes 16 MHz 2% when the PLL multiplication rate is Selectable subclock source • Suboscillation clock kHz • External clock kHz • Sub-CR clock Typ 100 kHz, Min 50 kHz, Max 150 kHz • Timer 8/16-bit composite timer 2 channels 8/16-bit PPG 2 channels 16-bit PPG timer 2 channels 16-bit reload timer 1 channel Time-base timer 1 channel Watch prescaler 1 channel • UART/SIO 1 channel Full duplex double buffer Capable of clock asynchronous UART serial data transfer and clock synchronous SIO serial data transfer • I2C bus interface 1 channel Built-in wake-up function • LIN-UART Full duplex double buffer Capable of clock asynchronous serial data transfer and clock synchronous serial data transfer • External interrupt 12 channels Interrupt by edge detection rising edge, falling edge, and both edges can be selected Can be used to wake up the device from different low power consumption standby modes • 8/10-bit A/D converter 12 channels 8-bit or 10-bit resolution can be selected. • Low power consumption standby modes There are four standby modes as follows • Stop mode • Sleep mode • Watch mode • Time-base timer mode In standby mode, two further options can be selected normal standby mode and deep standby mode. • I/O port no. of I/O ports 58 General-purpose I/O ports CMOS I/O 54 General-purpose I/O ports N-ch open drain 4 • On-chip debug 1-wire serial control Serial writing supported asynchronous mode • Hardware/software watchdog timer Built-in hardware watchdog timer Built-in software watchdog timer • Power-on reset A power-on reset is generated when the power is switched on. • Low-voltage detection LVD reset circuit The LVD function is enabled by default. For details, see Recommended Operating Conditions” in “Electrical Characteristics”. The LVD function can be controlled through software. The LVD reset circuit control register LVDCC enables or disables the LVD reset. The LVD reset circuit has an internal low-voltage detector. The combination of detection voltage and release voltage can be selected from four options. • Comparator 2 channels Built-in dedicated BGR The comparator reference voltage can be selected between the BGR voltage and the comparator pin. • Clock supervisor counter Built-in clock supervisor counter • Dual operation Flash memory The program/erase operation and the read operation can be executed in different banks upper bank/lower bank simultaneously. • Flash memory security function Protects the content of the Flash memory. • San Jose, CA 95134-1709 • 408-943-2600 MB95810K Series Contents 1 Product Line-up 3 Packages And Corresponding Products.................... 5 Differences Among Products And Notes On Product Selection 5 Pin Assignment 6 Pin 7 I/O Circuit Type 11 Handling 13 Precautions for Product Design........................... 13 Precautions for Package Mounting 14 Precautions for Use Environment........................ 16 Notes On Device 16 Pin Connection 17 Block Diagram 19 CPU 20 Memory Space 21 I/O area addresses 0x0000 to 0x007F ........... 21 Extended I/O area addresses 0x0F80 to 0x0FFF 21 Data 21 Program area 21 Memory space 22 Areas For Specific Applications 23 I/O 24 I/O 30 Port 31 Port 34 Port 39 Port 42 Port 48 Port 51 Port 55 Port 60 Port 63 Port E 66 Port 69 Port G 72 Interrupt Source Table 74 Pin States In Each Mode 75 Electrical 78 Absolute Maximum Ratings............................... 78 Recommended Operating Conditions 80 DC Characteristics 81 AC 84 A/D 104 Flash Memory Program/Erase Characteristics 108 Sample 109 Ordering 116 Package 117 Major Changes In This Edition 119 Document History Page 120 Sales, Solutions, and Legal Information 121 Page 2 of 121 MB95810K Series Product Line-up MB95F814K MB95F816K MB95F818K Parameter Type Flash memory product Clock supervisor counter It supervises the main clock oscillation and the subclock oscillation. Flash memory capacity 20 Kbyte 36 Kbyte 60 Kbyte RAM capacity 512 bytes 1 Kbyte 2 Kbyte Power-on reset Low-voltage detection reset Controlled through software Reset input Selected through software CPU functions • Number of basic instructions • Instruction bit length 8 bits • Instruction length 1 to 3 bytes • Data bit length 1, 8 and 16 bits • Minimum instruction execution time ns machine clock frequency = MHz • Interrupt processing time µs machine clock frequency = MHz Generalpurpose I/O • I/O port • CMOS I/O • N-ch open drain 58 54 :4 Ordering Information MB95F814KPMC1-G-SNE2 MB95F816KPMC1-G-SNE2 MB95F818KPMC1-G-SNE2 MB95F814KPMC-G-SNE2 MB95F816KPMC-G-SNE2 MB95F818KPMC-G-SNE2 MB95F818KPMC-G-UNE2 MB95810K Series Package 64-pin plastic LQFP FPT-64P-M38 64-pin plastic LQFP FPT-64P-M39 Page 116 of 121 MB95810K Series Package Dimension 64-pin plastic LQFP FPT-64P-M38 Lead pitch Package width x package length Lead shape Lead bend direction Sealing method Mounting height Weight mm x mm Gullwing Normal bend Plastic mold mm MAX 64-pin plastic LQFP FPT-64P-M38 12.00±0.20 .472±.008 SQ 10.00±0.10 .394±.004 SQ Note 1 These dimensions do not include resin protrusion. Note 2 Pins width and pins thickness include plating thickness. Note 3 Pins width do not include tie bar cutting remainder. INDEX C 2010 FUJITSU SEMICONDUCTOR LIMITED F64038S-c-1-2 Details of "A" part Mounting height 0~8° Stand off Dimensions in mm inches . Note The values in parentheses are reference values. Page 117 of 121 MB95810K Series 64-pin plastic LQFP FPT-64P-M39 Lead pitch Package width x package length Lead shape Sealing method Mounting height Weight mm x mm Gullwing Plastic mold mm MAX 64-pin plastic LQFP FPT-64P-M39 14.00±0.20 .551±.008 SQ 12.00±0.10 .472±.004 SQ Added MB95F818KPMC-G-UNE2 in "Ordering Information". Page 120 of 121 MB95810K Series Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Microcontrollers Automotive Clocks & Buffers Interface Lighting & Power Control Memory PSoC Touch Sensing USB Controllers Wireless/RF cypress.com/arm cypress.com/automotive cypress.com/clocks cypress.com/interface cypress.com/powerpsoc cypress.com/memory cypress.com/psoc cypress.com/touch cypress.com/usb cypress.com/wireless Solutions cypress.com/psoc 1 \| PSoC 3 \| PSoC 4 \| PSoC 5LP Cypress Developer Community \| Forums \| Blogs \| Video \| Training Technical Support cypress.com/support Cypress Semiconductor Corporation This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC "Cypress" . This document, including any software or firmware included or referenced in this document "Software" , is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you under its copyright rights in the Software, a personal, non-exclusive, nontransferable license without the right to sublicense a for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and b to distribute the Software in binary code form externally to end users either directly or indirectly through resellers and distributors , solely for use on Cypress hardware product units. Cypress also grants you a personal, non-exclusive, nontransferable, license without the right to sublicense under those claims of Cypress's patents that are infringed by the Software as provided by Cypress, unmodified to make, use, distribute, and import the Software solely to the minimum extent that is necessary for you to exercise your rights under the copyright license granted in the previous sentence. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems including resuscitation equipment and surgical implants , pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage "Unintended Uses" . A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and Company shall and hereby does release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. Company shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. Page 121 of 121 <Trademarks 0paragraph style, 6 points . To change this, view and correct the Master page. Delete this line but leave this paragraph marker for correct spacing. FOR TRADEMARK EXAMPLES:>

PDF Datasheet Preview

MB95810K Series

New 8FX 8-bit Microcontrollers

The MB95810K Series is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of these series contain a variety of peripheral resources.
• F2MC-8FX CPU core Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instructions
• Bit manipulation instructions, etc.
• Clock Selectable main clock source
• Main oscillation clock up to MHz, maximum machine clock frequency MHz
• External clock up to MHz, maximum machine clock frequency MHz
• Main CR clock 4 MHz 2%
• Main CR PLL clock - The main CR PLL clock frequency becomes 8 MHz 2% when the PLL multiplication rate is - The main CR PLL clock frequency becomes 10 MHz 2% when the PLL multiplication rate is - The main CR PLL clock frequency becomes 12 MHz 2% when the PLL multiplication rate is - The main CR PLL clock frequency becomes 16 MHz 2% when the PLL multiplication rate is

Selectable subclock source
• Suboscillation clock kHz
• External clock kHz
• Sub-CR clock Typ 100 kHz, Min 50 kHz, Max 150 kHz
• Timer 8/16-bit composite timer 2 channels 8/16-bit PPG 2 channels 16-bit PPG timer 2 channels 16-bit reload timer 1 channel Time-base timer 1 channel Watch prescaler 1 channel
• UART/SIO 1 channel Full duplex double buffer Capable of clock asynchronous UART serial data transfer and clock synchronous SIO serial data transfer
• I2C bus interface 1 channel Built-in wake-up function
• LIN-UART Full duplex double buffer Capable of clock asynchronous serial data transfer and clock synchronous serial data transfer
• External interrupt 12 channels Interrupt by edge detection rising edge, falling edge, and both edges can be selected

Can be used to wake up the device from different low power consumption standby modes
• 8/10-bit A/D converter 12 channels 8-bit or 10-bit resolution can be selected.
• Low power consumption standby modes There are four standby modes as follows
• Stop mode
• Sleep mode
• Watch mode
• Time-base timer mode In standby mode, two further options can be selected normal standby mode and deep standby mode.
• I/O port no. of I/O ports 58 General-purpose I/O ports CMOS I/O 54 General-purpose I/O ports N-ch open drain 4
• On-chip debug 1-wire serial control Serial writing supported asynchronous mode
• Hardware/software watchdog timer Built-in hardware watchdog timer Built-in software watchdog timer
• Power-on reset A power-on reset is generated when the power is switched on.
• Low-voltage detection LVD reset circuit The LVD function is enabled by default. For details, see Recommended Operating Conditions” in “Electrical Characteristics”. The LVD function can be controlled through software. The LVD reset circuit control register LVDCC enables or disables the LVD reset. The LVD reset circuit has an internal low-voltage detector. The combination of detection voltage and release voltage can be selected from four options.
• Comparator 2 channels Built-in dedicated BGR The comparator reference voltage can be selected between the BGR voltage and the comparator pin.
• Clock supervisor counter Built-in clock supervisor counter
• Dual operation Flash memory The program/erase operation and the read operation can be executed in different banks upper bank/lower bank simultaneously.
• Flash memory security function Protects the content of the Flash memory.
• San Jose, CA 95134-1709
• 408-943-2600

MB95810K Series

Contents
1 Product Line-up 3 Packages And Corresponding Products.................... 5 Differences Among Products And Notes On Product Selection 5 Pin Assignment 6 Pin 7 I/O Circuit Type 11 Handling 13

Precautions for Product Design........................... 13 Precautions for Package Mounting 14 Precautions for Use Environment........................ 16 Notes On Device 16 Pin Connection 17 Block Diagram 19 CPU 20 Memory Space 21 I/O area addresses 0x0000 to 0x007F ........... 21 Extended I/O area addresses 0x0F80 to 0x0FFF 21 Data 21 Program area 21 Memory space 22 Areas For Specific Applications 23 I/O 24

I/O 30 Port 31 Port 34 Port 39 Port 42 Port 48 Port 51 Port 55 Port 60 Port 63 Port E 66 Port 69 Port G 72

Interrupt Source Table 74

Pin States In Each Mode 75

Electrical 78 Absolute Maximum Ratings............................... 78 Recommended Operating Conditions 80 DC Characteristics 81 AC 84 A/D 104 Flash Memory Program/Erase Characteristics 108

Sample 109
Ordering 116

Package 117

Major Changes In This Edition 119 Document History Page 120 Sales, Solutions, and Legal Information 121

Page 2 of 121

MB95810K Series

Product Line-up

MB95F814K

MB95F816K

MB95F818K

Parameter

Type

Flash memory product

Clock supervisor counter

It supervises the main clock oscillation and the subclock oscillation.

Flash memory capacity
20 Kbyte
36 Kbyte
60 Kbyte

RAM capacity
512 bytes
1 Kbyte
2 Kbyte

Power-on reset

Low-voltage detection reset

Controlled through software

Reset input

Selected through software

CPU functions
• Number of basic instructions
• Instruction bit length
8 bits
• Instruction length
1 to 3 bytes
• Data bit length
1, 8 and 16 bits
• Minimum instruction execution time ns machine clock frequency = MHz
• Interrupt processing time
µs machine clock frequency = MHz

Generalpurpose I/O
• I/O port
• CMOS I/O
• N-ch open drain
58 54 :4
Ordering Information

MB95F814KPMC1-G-SNE2 MB95F816KPMC1-G-SNE2 MB95F818KPMC1-G-SNE2

MB95F814KPMC-G-SNE2 MB95F816KPMC-G-SNE2 MB95F818KPMC-G-SNE2 MB95F818KPMC-G-UNE2

MB95810K Series

Package 64-pin plastic LQFP

FPT-64P-M38 64-pin plastic LQFP

FPT-64P-M39

Page 116 of 121

MB95810K Series

Package Dimension
64-pin plastic LQFP

FPT-64P-M38

Lead pitch Package width x package length

Lead shape Lead bend direction Sealing method

Mounting height

Weight
mm x mm

Gullwing Normal bend Plastic mold mm MAX
64-pin plastic LQFP FPT-64P-M38
12.00±0.20 .472±.008 SQ
*10.00±0.10 .394±.004 SQ

Note 1 * These dimensions do not include resin protrusion. Note 2 Pins width and pins thickness include plating thickness. Note 3 Pins width do not include tie bar cutting remainder.

INDEX

C 2010 FUJITSU SEMICONDUCTOR LIMITED F64038S-c-1-2

Details of "A" part

Mounting height
0~8°

Stand off

Dimensions in mm inches . Note The values in parentheses are reference values.

Page 117 of 121

MB95810K Series
64-pin plastic LQFP FPT-64P-M39

Lead pitch Package width x package length

Lead shape

Sealing method

Mounting height

Weight
mm x mm

Gullwing Plastic mold mm MAX
64-pin plastic LQFP FPT-64P-M39
14.00±0.20 .551±.008 SQ 12.00±0.10 .472±.004 SQ
Added MB95F818KPMC-G-UNE2 in "Ordering Information".

Page 120 of 121

MB95810K Series

Sales, Solutions, and Legal Information

Worldwide Sales and Design Support

Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations.

Products Microcontrollers Automotive Clocks & Buffers Interface Lighting & Power Control Memory PSoC Touch Sensing USB Controllers Wireless/RF
cypress.com/arm cypress.com/automotive
cypress.com/clocks cypress.com/interface cypress.com/powerpsoc cypress.com/memory
cypress.com/psoc cypress.com/touch
cypress.com/usb cypress.com/wireless

Solutions cypress.com/psoc 1 | PSoC 3 | PSoC 4 | PSoC 5LP

Cypress Developer Community | Forums | Blogs | Video | Training

Technical Support cypress.com/support

Cypress Semiconductor Corporation This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC "Cypress" . This document, including any software or firmware included or referenced in this document "Software" , is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you under its copyright rights in the Software, a personal, non-exclusive, nontransferable license without the right to sublicense a for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and b to distribute the Software in binary code form externally to end users either directly or indirectly through resellers and distributors , solely for use on Cypress hardware product units. Cypress also grants you a personal, non-exclusive, nontransferable, license without the right to sublicense under those claims of Cypress's patents that are infringed by the Software as provided by Cypress, unmodified to make, use, distribute, and import the Software solely to the minimum extent that is necessary for you to exercise your rights under the copyright license granted in the previous sentence. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited.

CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems including resuscitation equipment and surgical implants , pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage "Unintended Uses" . A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and Company shall and hereby does release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. Company shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.

Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.

Page 121 of 121
<Trademarks 0paragraph style, 6 points . To change this, view and correct the Master page. Delete this line but leave this paragraph marker for correct spacing. FOR TRADEMARK EXAMPLES:>

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MB95F818KPMC-G-UNE2 Datasheet file may be downloaded here without warranties.

Datasheet ID: MB95F818KPMC-G-UNE2 508303