MB95F434HPMC-G-SNE2

MB95F434HPMC-G-SNE2 Datasheet


New 8FX MB95430H Series

Part Datasheet
MB95F434HPMC-G-SNE2 MB95F434HPMC-G-SNE2 MB95F434HPMC-G-SNE2 (pdf)
Related Parts Information
MB95F434KPMC-G-SNE2 MB95F434KPMC-G-SNE2 MB95F434KPMC-G-SNE2
MB95F433KPMC-G-SNE2 MB95F433KPMC-G-SNE2 MB95F433KPMC-G-SNE2
PDF Datasheet Preview
8-bit Microcontrollers

CMOS

New 8FX MB95430H Series

MB95F432H/F433H/F434H MB95F432K/F433K/F434K
• DESCRIPTION

MB95430H is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of this series contain a variety of peripheral resources.
• FEATURES
• F2MC-8FX CPU core Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instructions
• Bit manipulation instructions, etc.

Note F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
• Clock
• Selectable main clock source Main OSC clock up to MHz, maximum machine clock frequency MHz External clock up to MHz, maximum machine clock frequency MHz Main CR clock MHz ±2%, maximum machine clock frequency MHz
• Selectable subclock source Sub-OSC clock kHz External clock kHz Sub-CR clock Typ 100 kHz, Min 50 kHz, Max 200 kHz
• Timer
• 8/16-bit composite timer x 1 channel
• 16-bit PPG x 1 channel
• 16-bit free-running timer x 1 channel
• 16-bit output compare x 2 channels
• Time-base timer x 1 channel
• Watch prescaler x 1 channel
• UART/SIO x 1 channel
• Full duplex double buffer
• Capable of clock-asynchronous UART serial data transfer and clock-synchronous SIO serial data transfer Continued

For the information for microcontroller supports, see the following website.

Copyright 2011 FUJITSU SEMICONDUCTOR LIMITED All rights reserved

MB95430H Series

Continued
• I2C x 1 channel
• Built-in wake-up function
• Voltage comparator x 4 channels
• Operational amplifier OPAMP x 1 channel
• Software-select programmable gain
• Software-select standalone option
• Power down function included
• External interrupt x 8 channels
• Interrupt by edge detection rising edge, falling edge, and both edges can be selected
• Can be used to wake up the device from different low power consumption standby modes
• 8/10-bit A/D converter x 17 channels
• 8-bit and 10-bit resolution can be chosen.
• Low power consumption standby modes
• Stop mode
• Sleep mode
• Watch mode
• Time-base timer mode
• I/O port
• MB95F432H/F433H/F434H maximum no. of I/O ports 28

General-purpose I/O ports N-ch open drain 1

General-purpose I/O ports CMOS I/O
• MB95F432K/F433K/F434K maximum no. of I/O ports 29

General-purpose I/O ports N-ch open drain 2

General-purpose I/O ports CMOS I/O
• On-chip debug
• ORDERING INFORMATION

MB95F432HPMC-G-SNE2 MB95F432KPMC-G-SNE2 MB95F433HPMC-G-SNE2 MB95F433KPMC-G-SNE2 MB95F434HPMC-G-SNE2 MB95F434KPMC-G-SNE2

MB95F432HP-G-SH-SNE2 MB95F432KP-G-SH-SNE2 MB95F433HP-G-SH-SNE2 MB95F433KP-G-SH-SNE2 MB95F434HP-G-SH-SNE2 MB95F434KP-G-SH-SNE2

MB95430H Series

Package 32-pin plastic LQFP

FPT-32P-M30
32-pin plastic SH-DIP-32P-M06

MB95430H Series
• PACKAGE DIMENSION
32-pin plastic LQFP

Lead pitch Package width x package length

Lead shape

Sealing method

Mounting height
mm x mm

Gullwing Plastic mold mm MAX

FPT-32P-M30
32-pin plastic LQFP FPT-32P-M30
9.00±0.20 .354±.008 SQ * 7.00±0.10 .276±.004 SQ

Note 1 * These dimensions do not include resin protrusion. Note 2 Pins width and pins thickness include plating thickness. Note 3 Pins width do not include tie bar cutting remainder.

INDEX

Details of "A" part MAX Mounting height MAX
0~7°

C 2009-2010 FUJITSU SEMICONDUCTOR LIMITED F32051S-c-1-2

Dimensions in mm inches . Note The values in parentheses are reference values.

Please check the latest package dimension at the following URL.

Continued

Continued
32-pin plastic SDIP

MB95430H Series

Lead pitch Low space Sealing method
mm Plastic mold

DIP-32P-M06
32-pin plastic SDIP DIP-32P-M06

INDEX

Note 1 * These dimensions do not include resin protrusion. Note 2 Pins width and pins thickness include plating thickness.

MIN.

MAX.

C 2003-2010 FUJITSU SEMICONDUCTOR LIMITED D32018S-c-1-3
0~15°

Dimensions in mm inches . Note The values in parentheses are reference values
All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU SEMICONDUCTOR device FUJITSU SEMICONDUCTOR does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU SEMICONDUCTOR or any third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU SEMICONDUCTOR assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated 1 for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system , or 2 for use requiring extremely high reliability i.e., submersible repeater and artificial satellite . Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of overcurrent levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners.

Edited Sales Promotion Department
More datasheets: 15001 | FIT0511 | ADBS-A350 | 17000339A | 18482 | 808-187 | FAN8024CDTF | 74ALVC16373MTD | 74ALVC16373MTDX | MB95F434KPMC-G-SNE2


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MB95F434HPMC-G-SNE2 Datasheet file may be downloaded here without warranties.

Datasheet ID: MB95F434HPMC-G-SNE2 508302