MB95F204HP-G-SH-SNE2

MB95F204HP-G-SH-SNE2 Datasheet

MB95200H/210H Series

Part	Datasheet
MB95F204HP-G-SH-SNE2	MB95F204HP-G-SH-SNE2 (pdf)

Related Parts	Information
MB95F202HPF-G-SNE2	MB95F202HPF-G-SNE2
MB95F212HPF-G-SNE2	MB95F212HPF-G-SNE2
MB95F203HPF-G-SNE2	MB95F203HPF-G-SNE2
MB95F202HP-G-SH-SNE2	MB95F202HP-G-SH-SNE2

PDF Datasheet Preview
MB95200H/210H Series F2MC-8FX 8-bit Microcontroller MB95200H/210H is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of this series contain a variety of peripheral resources. F2MC-8FX CPU core Instruction set optimized for controllers • Multiplication and division instructions • 16-bit arithmetic operations • Bit test branch instructions • Bit manipulation instructions, etc. Clock main OSC clock and sub-OSC clock are only available in MB95F204H/F204K/F203H/F203K/F202H /F202K • Selectable main clock source Main OSC clock up to MHz, maximum machine clock frequency MHz External clock up to MHz, maximum machine clock frequency MHz Main internal CR clock 1/8/10 MHz ± 3%, maximum machine clock frequency 10 MHz • Selectable subclock source Sub-OSC clock kHz External clock kHz Sub-internal CR clock Typ 100 kHz, Min 50 kHz, Max 200 kHz Timer • 8/16-bit composite timer • Timebase timer • Watch prescaler LIN-UART MB95F204H/F204K/F203H/F203K/F202H /F202K • Full duplex double buffer Capable of clock-synchronized serial data transfer and clock-asynchronized serial data transfer External interrupt • Interrupt by edge detection rising edge, falling edge, and both edges can be selected • Can be used to wake up the device from different low-power consumption standby modes 8/10-bit A/D converter • 8-bit or 10-bit resolution can be selected. Low power consumption standby mode • Stop mode • Sleep mode • Watch mode • Timebase timer mode I/O port Max 17 MB95F204K/F203K/F202K • General-purpose I/O ports Max : CMOS I/O 15, N-ch open drain 2 I/O port Max 16 MB95F204H/F203H/F202H • General-purpose I/O ports Max : CMOS I/O 15, N-ch open drain 1 I/O port Max 5 MB95F214K/F213K/F212K • General-purpose I/O ports Max : CMOS I/O 3, N-ch open drain 2 I/O port Max 4 MB95F214H/F213H/F212H • General-purpose I/O ports Max : CMOS I/O 3, N-ch open drain 1 On-chip debug • 1-wire serial control • Serial writing supported asynchronous mode Hardware/software watchdog timer • Built-in hardware watchdog timer Low-voltage detection reset circuit • Built-in low-voltage detector Clock supervisor counter • Built-in clock supervisor counter function Programmable port input voltage level • CMOS input level / hysteresis input level Flash memory security function • Protects the contents of flash memory • San Jose, CA 95134-1709 • 408-943-2600 MB95200H/210H Series Contents Product Line-up 3 Packages and Corresponding Products 4 Differences Among Products And Notes On Product Selection 4 Pin Assignment 5 Pin Description MB95200H Series 24 pins 6 Pin Description MB95200H Series 20 pins 8 Pin Description MB95210H Series 10 I/O Circuit Type 11 Notes on Device Handling 13 Pin Connection 13 Block Diagram MB95200H Series 15 Block Diagram MB95210H Series 16 CPU Core 17 I/O Map MB95200H Series 18 I/O Map MB95210H Series 22 Interrupt Source Table MB95200H Series 26 Interrupt Source Table MB95210H Series 27 Electrical Characteristics 28 Absolute Maximum Ratings 28 Recommended Operating Conditions 30 DC Characteristics 31 AC Characteristics 34 A/D Converter 49 Flash Memory Program/Erase Characteristics 53 Sample Electrical Characteristics 54 Mask Options 60 Ordering Information 60 Package Dimensions 61 Major Changes 65 Document History 65 Page 2 of 66 MB95200H/210H Series Product Line-up Part number MB95 F204H Parameter MB95 F203H MB95 F202H MB95 F204K MB95 F203K MB95 F202K MB95 F214H MB95 F213H MB95 F212H MB95 F214K MB95 F213K MB95 F212K Type Flash memory product Clock supervisor It supervises the main clock oscillation. counter ROM capacity 16 KB 8 KB 4 KB 16 KB 8 KB 4 KB 16 KB 8 KB 4 KB 16 KB 8 KB 4 KB RAM capacity 496 B 496 B 240 B 496 B 496 B 240 B 496 B 496 B 240 B 496 B 496 B 240 B Low-voltage detection reset Reset input Dedicated Software select Dedicated Software select CPU functions Number of basic instructions Instruction bit length Instruction length Data bit length Minimum instruction execution time Interrupt processing time 136 8 bits 1 to 3 bytes 1, 8, and 16 bits ns with machine clock = MHz µs with machine clock = MHz General-purpose I/O ports Max 16 CMOS 15, N-ch 1 I/O ports Max 17 CMOS 15, N-ch 2 I/O ports Max 4 CMOS 3, N-ch 1 I/O ports Max 5 CMOS 3, N-ch 2 Timebase timer Interrupt cycle ms - s when external clock = 4 MHz Hardware/softwa Reset generation cycle re watchdog Main oscillation clock at 10 MHz 105 ms Min timer Ordering Information Part Number MB95F204HP-G-SH-SNE2 MB95F204KP-G-SH-SNE2 MB95F203HP-G-SH-SNE2 MB95F203KP-G-SH-SNE2 MB95F202HP-G-SH-SNE2 MB95F202KP-G-SH-SNE2 MB95F204HPF-G-SNE2 MB95F204KPF-G-SNE2 MB95F203HPF-G-SNE2 MB95F203KPF-G-SNE2 MB95F202HPF-G-SNE2 MB95F202KPF-G-SNE2 MB95F214HPH-G-SNE2 MB95F214KPH-G-SNE2 MB95F213HPH-G-SNE2 MB95F213KPH-G-SNE2 MB95F212HPH-G-SNE2 MB95F212KPH-G-SNE2 MB95F214HPF-G-SNE2 MB95F214KPF-G-SNE2 MB95F213HPF-G-SNE2 MB95F213KPF-G-SNE2 MB95F212HPF-G-SNE2 MB95F212KPF-G-SNE2 Package 24-pin plastic SDIP DIP-24P-M07 20-pin plastic SOP FPT-20P-M09 8-pin plastic DIP DIP-8P-M03 8-pin plastic SOP FPT-8P-M08 Page 60 of 66 Package Dimensions 24-pin plastic SDIP MB95200H/210H Series Lead pitch Package width x package length Sealing method Mounting height mm x mm Plastic mold mm Max DIP-24P-M07 24-pin plastic SDIP DIP-24P-M07 INDEX Note 1 Pins width and pins thickness include plating thickness. Note 2 Pins width do not include tie bar cutting remainder. Note 3 # These dimensions do not include resin protrusion. BTM E-MARK 4.80 .189 MAX C 2008-2010 FUJITSU SEMICONDUCTOR LIMITED D24066S-c-1-2 TYP. Dimensions in mm inches . Note The values in parentheses are reference values Continued Page 61 of 66 MB95200H/210H Series 20-pin plastic SOP FPT-20P-M09 20-pin plastic SOP FPT-20P-M09 Lead pitch Package width x package length Lead shape Lead bend direction Sealing method Mounting height mm x mm Gullwing Normal bend Plastic mold mm Max Note 1 Pins width and pins thickness include plating thickness. Note 2 Pins width do not include tie bar cutting remainder. Note 3 # These dimensions do not include resin protrusion. INDEX BTM E-MARK C 2008-2010 FUJITSU SEMICONDUCTOR LIMITED F20030S-c-1-2 Details of "A" part Mounting height

PDF Datasheet Preview

MB95200H/210H Series

F2MC-8FX 8-bit Microcontroller

MB95200H/210H is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of this series contain a variety of peripheral resources.

F2MC-8FX CPU core Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instructions
• Bit manipulation instructions, etc.

Clock main OSC clock and sub-OSC clock are only available in MB95F204H/F204K/F203H/F203K/F202H /F202K
• Selectable main clock source

Main OSC clock up to MHz, maximum machine clock frequency MHz

External clock up to MHz, maximum machine clock frequency MHz

Main internal CR clock 1/8/10 MHz ± 3%, maximum machine clock frequency 10 MHz
• Selectable subclock source Sub-OSC clock kHz External clock kHz Sub-internal CR clock Typ 100 kHz, Min 50 kHz, Max 200 kHz

Timer
• 8/16-bit composite timer
• Timebase timer
• Watch prescaler

LIN-UART MB95F204H/F204K/F203H/F203K/F202H /F202K
• Full duplex double buffer

Capable of clock-synchronized serial data transfer and clock-asynchronized serial data transfer

External interrupt
• Interrupt by edge detection rising edge, falling edge, and both
edges can be selected
• Can be used to wake up the device from different low-power
consumption standby modes
8/10-bit A/D converter
• 8-bit or 10-bit resolution can be selected.

Low power consumption standby mode
• Stop mode
• Sleep mode
• Watch mode
• Timebase timer mode I/O port Max 17 MB95F204K/F203K/F202K
• General-purpose I/O ports Max :

CMOS I/O 15, N-ch open drain 2 I/O port Max 16 MB95F204H/F203H/F202H
• General-purpose I/O ports Max :

CMOS I/O 15, N-ch open drain 1 I/O port Max 5 MB95F214K/F213K/F212K
• General-purpose I/O ports Max :

CMOS I/O 3, N-ch open drain 2 I/O port Max 4 MB95F214H/F213H/F212H
• General-purpose I/O ports Max :

CMOS I/O 3, N-ch open drain 1 On-chip debug
• 1-wire serial control
• Serial writing supported asynchronous mode Hardware/software watchdog timer
• Built-in hardware watchdog timer Low-voltage detection reset circuit
• Built-in low-voltage detector Clock supervisor counter
• Built-in clock supervisor counter function Programmable port input voltage level
• CMOS input level / hysteresis input level Flash memory security function
• Protects the contents of flash memory
• San Jose, CA 95134-1709
• 408-943-2600

MB95200H/210H Series

Contents

Product Line-up 3 Packages and Corresponding Products 4 Differences Among Products And Notes On Product Selection 4 Pin Assignment 5 Pin Description MB95200H Series 24 pins 6 Pin Description MB95200H Series 20 pins 8 Pin Description MB95210H Series 10 I/O Circuit Type 11 Notes on Device Handling 13 Pin Connection 13 Block Diagram MB95200H Series 15 Block Diagram MB95210H Series 16 CPU Core 17 I/O Map MB95200H Series 18 I/O Map MB95210H Series 22

Interrupt Source Table MB95200H Series 26 Interrupt Source Table MB95210H Series 27 Electrical Characteristics 28
Absolute Maximum Ratings 28 Recommended Operating Conditions 30 DC Characteristics 31 AC Characteristics 34 A/D Converter 49 Flash Memory Program/Erase Characteristics 53 Sample Electrical Characteristics 54 Mask Options 60 Ordering Information 60 Package Dimensions 61 Major Changes 65 Document History 65

Page 2 of 66

MB95200H/210H Series

Product Line-up

Part number MB95 F204H

Parameter

MB95 F203H

MB95 F202H

MB95 F204K

MB95 F203K

MB95 F202K

MB95 F214H

MB95 F213H

MB95 F212H

MB95 F214K

MB95 F213K

MB95 F212K

Type

Flash memory product

Clock supervisor It supervises the main clock oscillation. counter

ROM capacity 16 KB 8 KB 4 KB 16 KB 8 KB 4 KB 16 KB 8 KB 4 KB 16 KB 8 KB 4 KB

RAM capacity 496 B 496 B 240 B 496 B 496 B 240 B 496 B 496 B 240 B 496 B 496 B 240 B

Low-voltage detection reset

Reset input

Dedicated

Software select

Dedicated

Software select

CPU functions

Number of basic instructions Instruction bit length Instruction length Data bit length Minimum instruction execution time Interrupt processing time
136 8 bits 1 to 3 bytes 1, 8, and 16 bits ns with machine clock = MHz µs with machine clock = MHz

General-purpose I/O ports Max 16

CMOS 15, N-ch 1

I/O ports Max 17 CMOS 15, N-ch 2

I/O ports Max 4 CMOS 3, N-ch 1

I/O ports Max 5 CMOS 3, N-ch 2

Timebase timer Interrupt cycle ms - s when external clock = 4 MHz

Hardware/softwa Reset generation cycle
re watchdog

Main oscillation clock at 10 MHz 105 ms Min
timer
Ordering Information

Part Number MB95F204HP-G-SH-SNE2 MB95F204KP-G-SH-SNE2 MB95F203HP-G-SH-SNE2 MB95F203KP-G-SH-SNE2 MB95F202HP-G-SH-SNE2 MB95F202KP-G-SH-SNE2 MB95F204HPF-G-SNE2 MB95F204KPF-G-SNE2 MB95F203HPF-G-SNE2 MB95F203KPF-G-SNE2 MB95F202HPF-G-SNE2 MB95F202KPF-G-SNE2 MB95F214HPH-G-SNE2 MB95F214KPH-G-SNE2 MB95F213HPH-G-SNE2 MB95F213KPH-G-SNE2 MB95F212HPH-G-SNE2 MB95F212KPH-G-SNE2 MB95F214HPF-G-SNE2 MB95F214KPF-G-SNE2 MB95F213HPF-G-SNE2 MB95F213KPF-G-SNE2 MB95F212HPF-G-SNE2 MB95F212KPF-G-SNE2

Package 24-pin plastic SDIP

DIP-24P-M07 20-pin plastic SOP

FPT-20P-M09 8-pin plastic DIP

DIP-8P-M03 8-pin plastic SOP

FPT-8P-M08

Page 60 of 66

Package Dimensions
24-pin plastic SDIP

MB95200H/210H Series

Lead pitch Package width x package length Sealing method

Mounting height
mm x mm

Plastic mold mm Max

DIP-24P-M07
24-pin plastic SDIP DIP-24P-M07

INDEX

Note 1 Pins width and pins thickness include plating thickness. Note 2 Pins width do not include tie bar cutting remainder. Note 3 # These dimensions do not include resin protrusion.

BTM E-MARK
4.80 .189 MAX

C 2008-2010 FUJITSU SEMICONDUCTOR LIMITED D24066S-c-1-2

TYP.

Dimensions in mm inches . Note The values in parentheses are reference values

Continued

Page 61 of 66

MB95200H/210H Series
20-pin plastic SOP

FPT-20P-M09
20-pin plastic SOP FPT-20P-M09

Lead pitch Package width x package length

Lead shape Lead bend direction Sealing method

Mounting height
mm x mm

Gullwing Normal bend Plastic mold mm Max

Note 1 Pins width and pins thickness include plating thickness. Note 2 Pins width do not include tie bar cutting remainder. Note 3 # These dimensions do not include resin protrusion.

INDEX

BTM E-MARK

C 2008-2010 FUJITSU SEMICONDUCTOR LIMITED F20030S-c-1-2

Details of "A" part

Mounting height

More datasheets: 426495700-3 | 426493700-3 | 426496000-3 | 426495500-3 | 426495100-3 | 426495600-3 | 426490900-3 | 426496900-3 | MB95F202HPF-G-SNE2 | MB95F212HPF-G-SNE2

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MB95F204HP-G-SH-SNE2 Datasheet file may be downloaded here without warranties.

Datasheet ID: MB95F204HP-G-SH-SNE2 508299