Figure CY3684 Assembly Development Board Layout
Part | Datasheet |
---|---|
![]() |
CY3684 (pdf) |
PDF Datasheet Preview |
---|
EZ-USB Development Kit Manual Getting Started Rev • Cypress Semiconductor • Personal Communications Division • • 15050 Avenue of Science • Suite 200 • San Diego, CA 92128 • Cypress Disclaimer Agreement The information in this document is subject to change without notice and should not be construed as a commitment by Cypress Semiconductor Corporation Incorporated. While reasonable precautions have been taken, Cypress Semiconductor Corporation assumes no responsibility for any errors that may appear in this document. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Cypress Semiconductor Corporation. Cypress Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Cypress Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Cypress Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Cypress Semiconductor and its officers, employees, subsidiaries, affiliates and distributors harmless against all claims, costs, damages, expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Cypress Semiconductor was negligent regarding the design or manufacture of the part. The acceptance of this document will be construed as an acceptance of the foregoing conditions. EZ-USB Development Kit Manual Getting Started, Version Copyright 2004, Cypress Semiconductor Corporation. All rights reserved. Table of Contents EZ-USB Development Kit Overview Introduction EZ-USB Development Kit Contents Required Tools Not Included. Other Suggested Tools. EZ-USB Development Kit Software. System Requirements Compatibility with Earlier EZ-USB Development Kits. Installation Instructions Verifying that the host PC supports USB. Installing the Development Kit Software Installing the Hardware. Confirm Successful Installation using the Cypress USB Console EZ-USB Advanced Development Board Introduction Schematic Summary. Jumpers EEPROM Select & Enable Switches SW1 and SW2. Interface Connectors. ATA Connector P8 U2 -- 22v10 GAL Memory Maps I2C Expanders and Breakpoint General Purpose Indicators. Frequently Asked Questions Appendix A U2 GAL code file is 'FX2LP.ABL' Table of Contents Getting Started EZ-USB Development Kit Overview Introduction The EZ-USB Development Kit DVK is the best starting point for developing an EZ-USB based product. The DVK includes everything you will need to get started A development board, example firmware, a generic device driver, documentation, and assorted tools. This manual provides a general overview and installation guide for the DVK. The software installation of the kit includes additional help files and documentation more specific to the various components in the kit. The DVK is designed to work with the EZ-USB FX2LP and FX1 chips. FX1 is a full-speed only version of FX2LP. Other than the absence of a high-speed transceiver, FX1 is identical to FX2LP. Except where distinction is required, both chips will be generically referred to as EZ-USB throughout this manual. EZ-USB Development Kit Contents The following list shows the components supplied in the EZ-USB EZ-USB Development Kit. They represent most of the development tools required to build a USB system. Hardware • EZ-USB Advanced Development Board • EZ-USB Proto-typing Board “Breadboard” • USB Cable • RS-232 Cable • Software Installation CD-ROM Software on CD-ROM • EZ-USB Firmware Library and Firmware Frameworks • Firmware Sample Code • Cypress Generic USB Driver • Cypress USB Class Library CyApi EZ-USB Development Board Page -1 EZ-USB Development Kit Manual - Getting Started • Cypress USB Console • Cypress GPIF Designer • Cypress Firmware Download Driver sample • EZ-USB Documentation and Help Files • Reference Schematics • Limited Evaluation Version of the Keil 8051 Development Tools Compiler, Assembler, IDE, Debugger Required Tools Not Included • Full retail Keil Development System Keil uVision2 • Microsoft Visual C++ all PC sample code is developed under this platform • USB capable PC running Windows XP, 2000, or ME Other Suggested Tools • CATC USB Protocol Analyzer EZ-USB Development Kit Software System Requirements |
More datasheets: VRAH-07C1A00 | 8188 | WM1824BGEDT | WM1824BGEDT/R | M39143 SL005 | M39143 SL002 | M39143 SL001 | 19039692A | 1195 | 1383-2UYT/S530-A3 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived CY3684 Datasheet file may be downloaded here without warranties.