CYRF69213-40LTXC

CYRF69213-40LTXC Datasheet

CYRF69213

Part	Datasheet
CYRF69213-40LTXC	CYRF69213-40LTXC (pdf)

PDF Datasheet Preview
CYRF69213 Programmable Radio on Chip Low Power Programmable Radio on Chip Low Power PRoC LP Features • USB 2.0-USB-IF certified TID # 40000552 • Single Device, Two Functions 8-bit, Flash based USB peripheral MCU function and GHz radio transceiver function in a single device • Flash Based Microcontroller Function M8C based 8-bit CPU, optimized for Human Interface Devices HID applications 256 bytes of SRAM 8 Kbytes of Flash memory with EEPROM emulation In-System reprogrammable through pins 16-bit free running timer Low power wake up timer 12-bit Programmable Interval Timer with interrupts Watchdog timer • Industry-Leading GHz Radio Transceiver Function Operates in the unlicensed worldwide Industrial, Scientific and Medical ISM band GHz to GHz DSSS data rates of up to 250 Kbps GFSK data rate of 1 Mbps dBm receive sensitivity Programmable output power of up to +4 dBm Auto Transaction Sequencer ATS Framing CRC and Auto ACK Received Signal Strength Indication RSSI Automatic Gain Control AGC • Component Reduction Integrated V regulator Integrated pull up on GPIOs that require no external components Operates off a single crystal • Flexible I/O 2 mA source current on all GPIO pins. Configurable 8 mA or 50 mA/pin current sink on designated pins Each GPIO pin supports high impedance inputs, configurable pull up, open-drain output, CMOS/TTL inputs and CMOS output Maskable interrupts on all I/O pins • USB Specification Compliance Conforms to USB Specification Version Conforms to USB HID Specification Version Supports one Low Speed USB device address Supports one control endpoint and two data end points Integrated USB Transceiver • Operating Voltage from V to V DC • Operating Temperature from 0 to 70C • Pb-free 40-pin QFN Package • Advanced Development Tools Based on Cypress’s Tools Block Diagram Vbus 4.7uF 1-2 uF 1ohm 470nF MOSI SCK nSS RST VBat2 VBat1 VBat0 VReg VCC1 VCC2 VCC3 P1.2 / VReg VDD_MICRO Microcontroller P0_1,3,4,7 4 P1_6:7 2 Function P1.5/MOSI P1.4/SCK P2_0:1 2 P1.3/nSS D+/D2 GND Xtal RESV GND VSS RFbias Radio Function IRQ/GPIO MISO/GPIO XOUT/GPIO PACTL/GPIO 12MHz 470nF • San Jose, CA 95134-1709 • 408-943-2600 Clock Architecture Description 27 CPU Clock During Sleep Mode 33 Reset 33 Power on Reset 35 Watchdog Timer Reset 35 Sleep Mode 35 Sleep Sequence 35 Wakeup Sequence 36 Low Voltage Detect Control 38 POR Compare State 38 ECO Trim Register 39 General-Purpose I/O Ports 39 Port Data Registers 39 GPIO Port Configuration 40 GPIO Configurations for Low Power Mode 45 Serial Peripheral Interface SPI 46 SPI Data Register 47 SPI Configure Register 47 Timer Registers 49 Registers 49 Interrupt Controller 52 Architectural Description 52 Interrupt Processing 53 Interrupt Latency 53 Interrupt Registers 53 USB Transceiver 57 USB Transceiver Configuration 57 VREG Control 57 USB Serial Interface Engine SIE 58 USB Device 58 Endpoint 0 Mode 60 Endpoint Data Buffers 61 USB Mode Tables 63 Mode Column 63 Encoding Column 63 SETUP, IN, and OUT Columns 63 Details of Mode for Differing Traffic Conditions 64 Register Summary 67 Radio Function Register Descriptions 70 Absolute Maximum Ratings 71 DC Characteristics 71 RF Characteristics 74 AC Test Loads and Waveforms for Digital Pins 75 AC Electrical Characteristics 76 Ordering Information 82 Ordering Code Definitions 82 Package Diagram 83 Page 2 of 86 Document History Page 85 Sales, Solutions, and Legal Information 86 Worldwide Sales and Design Support 86 Products 86 PSoC Solutions 86 CYRF69213 Page 3 of 86 CYRF69213 The CYRF69213 PRoC LP Low Speed is targeted for the following applications: • USB Bridge for Human Interface Devices HID Wireless mice Wireless keyboards Remote controls Gaming applications • USB Bridge for General Purpose Applications Consumer electronics Industrial applications White goods Home automation Personal health Functional Description PRoC LP devices are integrated radio and microcontroller functions in the same package to provide a dual role single-chip solution. Communication between the microcontroller and the radio is via the SPI interface between both functions. Functional Overview The CYRF69213 is a complete Radio System-on-Chip device, providing a complete RF system solution with a single device and a few discrete components. The CYRF69213 is designed to implement low cost wireless systems operating in the worldwide GHz Industrial, Scientific, and Medical ISM frequency band GHz . GHz Radio Function The radio meets the following world wide regulatory requirements: • Europe ETSI EN 301 489-1 V1.4.1 ETSI EN 300 328-1 V1.3.1 • North America FCC CFR 47 Part 15 • Japan ARIB STD-T66 Data Transmission Modes The radio supports four different data transmission modes: • In GFSK mode, data is transmitted at 1 Mbps without any DSSS • In 8DR mode, 1 byte is encoded in each PN code symbol transmitted • In DDR mode, 2 bits are encoded in each PN code symbol transmitted • In SDR mode, a single bit is encoded in each PN code symbol transmitted Both 64-chip and 32-chip data PN codes are supported. The four data transmission modes apply to the data after the Start of Packet SOP . In particular, the packet length, data and CRC are all sent in the same mode. USB Microcontroller Function The microcontroller function is based on the powerful CYRF69213 microcontroller. It is an 8-bit Flash programmable microcontroller with integrated low speed USB interface. The microcontroller has up to 14 GPIO pins to support USB, PS/2 and other applications. Each GPIO port supports high impedance inputs, configurable pull up, open drain output, CMOS/TTL inputs and CMOS output. Up to two pins support programmable drive strength of up to 50 mA. Additionally each I/O pin can be used to generate a GPIO interrupt to the microcontroller. Each GPIO port has its own GPIO interrupt vector with the exception of GPIO Port The microcontroller features an internal oscillator. With the presence of USB traffic, the internal oscillator can be set to precisely tune to USB timing requirements 24 MHz ± The PRoC LP has up to 8 Kbytes of Flash for user’s firmware code and up to 256 bytes of RAM for stack space and user variables. The PRoC LP includes a Watchdog timer, a vectored interrupt controller, a 12-bit programmable interval timer with configurable 1 ms interrupt and a 16-bit free running timer with capture registers. Page 4 of 86 CYRF69213 Pin Configurations Figure 40-pin QFN pinout PACTL / GPIO 31 P1.6 32 VIO 33 RST 34 P1.7 35 VDD_1.8 36 L/D 37 P0.7 38 VBAT0 39 VREG 40 Corner tabs Ordering Information Package 40-pin Pb-free QFN 6 x 6 mm Sawn 40-pin Pb-free QFN 6 x 6 mm Punch Ordering Code Definitions CY RF 69213 40 L F,T X C Ordering Part Number CYRF69213-40LTXC CYRF69213-40LFXC Status In Production NRND Temperature range Commercial 40- pin package F = QFN T = Sawn QFN X = Pb-free Marketing Code:RF = Wireless radio frequency product line Company ID CY = Cypress Page 82 of 86 CYRF69213 Package Diagram Figure 40-pin QFN 6 x 6 x mm LT40B x mm E-Pad Sawn Package Outline, 001-13190 001-13190 H Page 83 of 86 CYRF69213 Figure 40-pin QFN 6 x 6 x mm LF40A/LY40A x mm E-Pad Punch Package Outline, 001-12917 [15] SOLDERABLE EXPOSED PAD 001-12917 C Note Not Recommended for New Design. Page 84 of 86 CYRF69213 Document History Page Document Title CYRF69213, Programmable Radio on Chip Low Power Document # 001-07552 ECN No. Orig. of Submission Change Description of Change 436355 See ECN New advance data sheet. 501280 See ECN Preliminary data sheet. 631538 See ECN Final datasheet. Updated DC Characteristics table with characterization data. Minor text changes Removed all residual references to external crystal oscillator and GPIO4 Voltage regulator line/load regulation documented GPIO capacitance and timing diagram included Sleep and Wake up sequence documented. EP1MODE/EP2MODE register issue discussed Updated radio function register descriptions Changed L/D pin description Changed RST Capacitor from 0.1uF to 0.47uF 2447906 VNY / VGT See ECN Modified figure 1 Vbat changed to Vbat 0,1,2 for pins 36,6 and 9 3550855 ANTG 03/15/2012 Added new ordering part number for Sawn type package Added new package diagram for Sawn type package. Added a section “Receive Spurious Response” Added note# 16 and provided reference to it in Table 88 Added ordering code definition Updated the package diagram for Punch type package 3717153 ANKC 08/18/2012 Updated Ordering Information No change in part numbers, included a column “Status” . added Note 15 and referred the same note in Figure Updated in new template. 3981780 ANKC 04/25/2013 Updated Pin Configurations Updated Figure Updated Pin Definitions Updated Name and Function of Pin 21 and Pin Page 85 of 86 CYRF69213 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control Memory PSoC Touch Sensing USB Controllers Wireless/RF cypress.com/go/automotive cypress.com/go/clocks cypress.com/go/interface cypress.com/go/powerpsoc cypress.com/go/plc cypress.com/go/memory cypress.com/go/psoc cypress.com/go/touch cypress.com/go/USB cypress.com/go/wireless PSoC Solutions psoc.cypress.com/solutions PSoC 1 \| PSoC 3 \| PSoC 5 Cypress Semiconductor Corporation, The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code software and/or firmware is owned by Cypress Semiconductor Corporation Cypress and is protected by and subject to worldwide patent protection United States and foreign , United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Page 86 of 86 WirelessUSB, PSoC, enCoRe and PRoC are trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders.

PDF Datasheet Preview

CYRF69213

Programmable Radio on Chip Low Power

Programmable Radio on Chip Low Power

PRoC LP Features
• USB 2.0-USB-IF certified TID # 40000552
• Single Device, Two Functions 8-bit, Flash based USB peripheral MCU function and GHz radio transceiver function in a single device
• Flash Based Microcontroller Function M8C based 8-bit CPU, optimized for Human Interface Devices HID applications 256 bytes of SRAM 8 Kbytes of Flash memory with EEPROM emulation In-System reprogrammable through pins 16-bit free running timer Low power wake up timer 12-bit Programmable Interval Timer with interrupts Watchdog timer
• Industry-Leading GHz Radio Transceiver Function Operates in the unlicensed worldwide Industrial, Scientific and Medical ISM band GHz to GHz DSSS data rates of up to 250 Kbps GFSK data rate of 1 Mbps dBm receive sensitivity Programmable output power of up to +4 dBm Auto Transaction Sequencer ATS Framing CRC and Auto ACK Received Signal Strength Indication RSSI

Automatic Gain Control AGC
• Component Reduction Integrated V regulator Integrated pull up on GPIOs that require no external components Operates off a single crystal
• Flexible I/O 2 mA source current on all GPIO pins. Configurable 8 mA or 50 mA/pin current sink on designated pins Each GPIO pin supports high impedance inputs, configurable pull up, open-drain output, CMOS/TTL inputs and CMOS output Maskable interrupts on all I/O pins
• USB Specification Compliance Conforms to USB Specification Version Conforms to USB HID Specification Version Supports one Low Speed USB device address Supports one control endpoint and two data end points Integrated USB Transceiver
• Operating Voltage from V to V DC
• Operating Temperature from 0 to 70C
• Pb-free 40-pin QFN Package
• Advanced Development Tools Based on Cypress’s Tools

Block Diagram

Vbus
4.7uF
1-2 uF
1ohm
470nF

MOSI SCK nSS

RST VBat2 VBat1 VBat0 VReg VCC1 VCC2 VCC3

P1.2 / VReg

VDD_MICRO

Microcontroller

P0_1,3,4,7 4

P1_6:7 2

Function

P1.5/MOSI P1.4/SCK

P2_0:1 2

P1.3/nSS

D+/D2

GND Xtal RESV GND VSS

RFbias

Radio Function

IRQ/GPIO MISO/GPIO XOUT/GPIO PACTL/GPIO
12MHz
470nF
• San Jose, CA 95134-1709
• 408-943-2600
Clock Architecture Description 27 CPU Clock During Sleep Mode 33 Reset 33 Power on Reset 35 Watchdog Timer Reset 35 Sleep Mode 35 Sleep Sequence 35 Wakeup Sequence 36 Low Voltage Detect Control 38 POR Compare State 38 ECO Trim Register 39 General-Purpose I/O Ports 39 Port Data Registers 39 GPIO Port Configuration 40 GPIO Configurations for Low Power Mode 45 Serial Peripheral Interface SPI 46 SPI Data Register 47 SPI Configure Register 47 Timer Registers 49 Registers 49 Interrupt Controller 52 Architectural Description 52 Interrupt Processing 53 Interrupt Latency 53 Interrupt Registers 53 USB Transceiver 57 USB Transceiver Configuration 57 VREG Control 57 USB Serial Interface Engine SIE 58 USB Device 58 Endpoint 0 Mode 60 Endpoint Data Buffers 61 USB Mode Tables 63 Mode Column 63 Encoding Column 63 SETUP, IN, and OUT Columns 63 Details of Mode for Differing Traffic Conditions 64 Register Summary 67 Radio Function Register Descriptions 70 Absolute Maximum Ratings 71 DC Characteristics 71 RF Characteristics 74 AC Test Loads and Waveforms for Digital Pins 75 AC Electrical Characteristics 76 Ordering Information 82 Ordering Code Definitions 82 Package Diagram 83

Page 2 of 86

Document History Page 85 Sales, Solutions, and Legal Information 86

Worldwide Sales and Design Support 86 Products 86 PSoC Solutions 86

CYRF69213

Page 3 of 86

CYRF69213

The CYRF69213 PRoC LP Low Speed is targeted for the following applications:
• USB Bridge for Human Interface Devices HID Wireless mice Wireless keyboards Remote controls Gaming applications
• USB Bridge for General Purpose Applications Consumer electronics Industrial applications White goods Home automation Personal health

Functional Description

PRoC LP devices are integrated radio and microcontroller functions in the same package to provide a dual role single-chip solution.

Communication between the microcontroller and the radio is via the SPI interface between both functions.

Functional Overview

The CYRF69213 is a complete Radio System-on-Chip device, providing a complete RF system solution with a single device and a few discrete components. The CYRF69213 is designed to implement low cost wireless systems operating in the worldwide GHz Industrial, Scientific, and Medical ISM frequency band GHz .

GHz Radio Function

The radio meets the following world wide regulatory requirements:
• Europe ETSI EN 301 489-1 V1.4.1 ETSI EN 300 328-1 V1.3.1
• North America FCC CFR 47 Part 15
• Japan ARIB STD-T66

Data Transmission Modes

The radio supports four different data transmission modes:
• In GFSK mode, data is transmitted at 1 Mbps without any DSSS
• In 8DR mode, 1 byte is encoded in each PN code symbol transmitted
• In DDR mode, 2 bits are encoded in each PN code symbol transmitted
• In SDR mode, a single bit is encoded in each PN code symbol transmitted

Both 64-chip and 32-chip data PN codes are supported. The four data transmission modes apply to the data after the Start of Packet SOP . In particular, the packet length, data and CRC are all sent in the same mode.

USB Microcontroller Function

The microcontroller function is based on the powerful CYRF69213 microcontroller. It is an 8-bit Flash programmable microcontroller with integrated low speed USB interface.

The microcontroller has up to 14 GPIO pins to support USB, PS/2 and other applications. Each GPIO port supports high impedance inputs, configurable pull up, open drain output, CMOS/TTL inputs and CMOS output. Up to two pins support programmable drive strength of up to 50 mA. Additionally each I/O pin can be used to generate a GPIO interrupt to the microcontroller. Each GPIO port has its own GPIO interrupt vector with the exception of GPIO Port

The microcontroller features an internal oscillator. With the presence of USB traffic, the internal oscillator can be set to precisely tune to USB timing requirements 24 MHz ±

The PRoC LP has up to 8 Kbytes of Flash for user’s firmware code and up to 256 bytes of RAM for stack space and user variables.

The PRoC LP includes a Watchdog timer, a vectored interrupt controller, a 12-bit programmable interval timer with configurable 1 ms interrupt and a 16-bit free running timer with capture registers.

Page 4 of 86

CYRF69213

Pin Configurations

Figure 40-pin QFN pinout

PACTL / GPIO 31 P1.6 32 VIO 33 RST 34 P1.7 35

VDD_1.8 36 L/D 37 P0.7 38

VBAT0 39 VREG 40

Corner tabs
Ordering Information

Package 40-pin Pb-free QFN 6 x 6 mm Sawn 40-pin Pb-free QFN 6 x 6 mm Punch
Ordering Code Definitions CY RF 69213 40 L F,T X C
Ordering Part Number CYRF69213-40LTXC CYRF69213-40LFXC

Status In Production NRND

Temperature range Commercial
40- pin package F = QFN T = Sawn QFN X = Pb-free

Marketing Code:RF = Wireless radio frequency product line

Company ID CY = Cypress

Page 82 of 86

CYRF69213

Package Diagram

Figure 40-pin QFN 6 x 6 x mm LT40B x mm E-Pad Sawn Package Outline, 001-13190
001-13190 *H

Page 83 of 86

CYRF69213

Figure 40-pin QFN 6 x 6 x mm LF40A/LY40A x mm E-Pad Punch Package Outline, 001-12917 [15]

SOLDERABLE EXPOSED PAD
001-12917 *C

Note Not Recommended for New Design.

Page 84 of 86

CYRF69213

Document History Page

Document Title CYRF69213, Programmable Radio on Chip Low Power Document # 001-07552

ECN No.

Orig. of Submission

Change

Description of Change
436355

See ECN New advance data sheet.
501280

See ECN Preliminary data sheet.
631538

See ECN Final datasheet. Updated DC Characteristics table with characterization data.

Minor text changes

Removed all residual references to external crystal oscillator and GPIO4

Voltage regulator line/load regulation documented

GPIO capacitance and timing diagram included

Sleep and Wake up sequence documented.

EP1MODE/EP2MODE register issue discussed

Updated radio function register descriptions

Changed L/D pin description

Changed RST Capacitor from 0.1uF to 0.47uF
2447906 VNY / VGT See ECN Modified figure 1 Vbat changed to Vbat 0,1,2 for pins 36,6 and 9
3550855 ANTG 03/15/2012 Added new ordering part number for Sawn type package

Added new package diagram for Sawn type package.

Added a section “Receive Spurious Response”

Added note# 16 and provided reference to it in Table 88
Added ordering code definition

Updated the package diagram for Punch type package
3717153 ANKC 08/18/2012 Updated Ordering Information No change in part numbers, included a column
“Status” .
added Note 15 and referred the same note in Figure

Updated in new template.
3981780 ANKC 04/25/2013 Updated Pin Configurations Updated Figure

Updated Pin Definitions Updated Name and Function of Pin 21 and Pin

Page 85 of 86

CYRF69213

Sales, Solutions, and Legal Information

Worldwide Sales and Design Support

Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations.

Products Automotive Clocks & Buffers Interface Lighting & Power Control

Memory PSoC Touch Sensing USB Controllers Wireless/RF
cypress.com/go/automotive cypress.com/go/clocks
cypress.com/go/interface cypress.com/go/powerpsoc
cypress.com/go/plc cypress.com/go/memory
cypress.com/go/psoc cypress.com/go/touch cypress.com/go/USB cypress.com/go/wireless

PSoC Solutions psoc.cypress.com/solutions PSoC 1 | PSoC 3 | PSoC 5

Cypress Semiconductor Corporation, The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.

Any Source Code software and/or firmware is owned by Cypress Semiconductor Corporation Cypress and is protected by and subject to worldwide patent protection United States and foreign , United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress.

Disclaimer CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.

Use may be limited by and subject to the applicable Cypress software license agreement.

Page 86 of 86

WirelessUSB, PSoC, enCoRe and PRoC are trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived CYRF69213-40LTXC Datasheet file may be downloaded here without warranties.

Datasheet ID: CYRF69213-40LTXC 508221