RI-90GP1030

RI-90GP1030 Datasheet

RI-90 Series Dry Reed Switch

Part	Datasheet
RI-90GP1030	RI-90GP1030 (pdf)

PDF Datasheet Preview
RI-90 Series Dry Reed Switch RI-90 Series Micro changeover dry-reed switch hermetically sealed in a gas-filled envelope. Single-pole, double-throw SPDT type, having a normally open and a normally closed contact. The switch may be actuated by an electromagnet, a permanent magnet or a combination of both. The device is intended for use in sensors, relays, pulse counters or similar devices. RI-90 Series Features Ideal for ATE switching & proximity sensors Contact layers Ruthenium on gold Superior glass-to-metal seal and blade alignment Excellent life expectancy and reliability General data for all models RI-90 AT-Customization / Preformed Leads Besides the standard models, customized products can also be supplied offering the following options ! Operate and release ranges to customer specification ! Cropped and/or preformed leads Coils All characteristics are measured using the Philips Standard Coil. For definitions of the Philips Standard Coil, see Reed Switch Technical & Application Information Section of this catalog. Life expectancy and reliability The life expectancy data given below are valid for a coil energized at times the published maximum operate value for each type in the RI-90 series. No load conditions operating frequency 100Hz Life expectancy min. 108 operations with a failure rate of less than 2 x 10-9 with a confidence level of Dimensions in inches mm End of life criteria Contact resistance > after 2 ms Release time > 2 ms latching or contact sticking . Switching different loads involves different life expectancy and reliability data. Further information is available on request. Operating and Storage Temperature Operating ambient temperature min -55°C max +125°C. Storage temperature min -55°C max +125°C. Note Temperature excursions up to 150°C may be permissible. For more information contact your nearest Coto Technology sales office. Soldering The switch can withstand soldering heat in accordance with “IEC 68-2-20”, test Tb, method 1B:solder bath at 350 ±10°C for s. Solderability is tested in accordance with “IEC 68-2-20”, test Ta, method 3 solder globule temperature 235°C ageing 1b 4 hours steam. Welding The leads can be welded. 94 COTO TECHNOLOGY USA Tel 401 943-2686 / Fax 401 942-0920 6 Europe Tel +31-45-5439343 / Fax +31-45-5427216 RI-90 Series Dry Reed Switch Mounting The leads should not be bent closer than 1 mm to the glass-to-metal seals. Stress on the seals should be avoided. Care must be taken to prevent stray magnetic fields from influencing the operating and measuring conditions. For Most Recent Data, Consult the Coto Technology Website 6 E-mail:

PDF Datasheet Preview

RI-90 Series Dry Reed Switch

RI-90 Series Micro changeover dry-reed switch hermetically sealed in a gas-filled envelope. Single-pole, double-throw SPDT type, having a normally open and a normally closed contact.

The switch may be actuated by an electromagnet, a permanent magnet or a combination of both.

The device is intended for use in sensors, relays, pulse counters or similar devices.

RI-90 Series Features Ideal for ATE switching & proximity sensors Contact layers Ruthenium on gold Superior glass-to-metal seal and blade alignment Excellent life expectancy and reliability

General data for all models RI-90

AT-Customization / Preformed Leads Besides the standard models, customized products can also be supplied offering the following options ! Operate and release ranges to customer
specification ! Cropped and/or preformed leads

Coils All characteristics are measured using the Philips Standard Coil. For definitions of the Philips Standard Coil, see Reed Switch Technical & Application Information Section of this catalog.

Life expectancy and reliability The life expectancy data given below are valid for a coil energized at times the published maximum operate value for each type in the RI-90 series.

No load conditions operating frequency 100Hz Life expectancy min. 108 operations with a failure rate of less than 2 x 10-9 with a confidence level of

Dimensions in inches mm

End of life criteria Contact resistance > after 2 ms Release time > 2 ms latching or contact sticking .

Switching different loads involves different life expectancy and reliability data. Further information is available on request.

Operating and Storage Temperature Operating ambient temperature min -55°C max +125°C. Storage temperature min -55°C max +125°C. Note Temperature excursions up to 150°C may be permissible. For more information contact your nearest Coto Technology sales office.

Soldering The switch can withstand soldering heat in accordance with “IEC 68-2-20”, test Tb, method 1B:solder bath at 350 ±10°C for s. Solderability is tested in accordance with “IEC 68-2-20”, test Ta, method 3 solder globule temperature 235°C ageing 1b 4 hours steam.

Welding The leads can be welded.
94 COTO TECHNOLOGY USA Tel 401 943-2686 / Fax 401 942-0920 6 Europe Tel +31-45-5439343 / Fax +31-45-5427216

RI-90 Series Dry Reed Switch

Mounting

The leads should not be bent closer than 1 mm to the glass-to-metal seals. Stress on the seals should be avoided. Care must be taken to prevent stray magnetic fields from influencing the operating and measuring conditions.

For Most Recent Data, Consult the Coto Technology Website 6 E-mail:

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived RI-90GP1030 Datasheet file may be downloaded here without warranties.

Datasheet ID: RI-90GP1030 506933