RI-01CA

RI-01CA Datasheet

RI-01C Series Dry Reed Switch

Part	Datasheet
RI-01CA	RI-01CA (pdf)

PDF Datasheet Preview
RI-01C Series Dry Reed Switch RI-01C Series Pico dry-reed switch hermetically sealed in a gas-filled glass envelope. Single-pole, single-throw SPST type, having normally open contacts, and containing two magnetically actuated reeds. The switch is of the double-ended type and may be actuated by an electromagnet, a permanent magnet or a combination of both. The device is intended for use in relays, sensors, pulse counters or similar devices. RI-01C Series Features Ideal for general purpose reed relays and sensors Contact layers Ruthenium on gold Superior glass-to-metal seal and blade alignment General data for all models RI-01C Dimensions in inches mm AT-Customization / Preformed Leads Besides the standard models, customized products can also be supplied offering the following options ! Operate and release ranges to customer specification ! Cropped and/or preformed leads Release time > 2ms latching or contact sticking . Loaded conditions resistive load 12V 4 mA 15 mA peak operating frequency 170 Hz Life expectancy min. 106 operations Coils All characteristics are measured using the Philips Standard Coil. For definitions of the Philips Standard Coil, refer to “Application Notes” in the Reed Switch Technical & Application Information Section of this catalog. End of life criteria Contact resistance > after 4 ms Release time > ms latching or contact sticking . Switching different loads involves different life expectancy and reliability data. Further information is available on request. Life expectancy and reliability The life expectancy data given below are valid for a coil energized at times the published maximum operate value for each type in the RI-01C series. Mechanical Data Contact arrangement is normally open lead finish is tinned net mass is approximately 100 mg and can be mounted in any position. No-load conditions operating frequency 100 Hz Life expectancy min. 108 operations with a failure rate of less than 10-9 with a confidence level of Shock The switches are tested in accordance with “IEC 68-227”, test Ea peak acceleration 150 G, half sinewave; End of life criteria Contact resistance > after 2 ms duration 11 ms . Such a shock will not cause an open switch no magnetic field present to close, nor a switch 116 COTO TECHNOLOGY USA Tel 401 943-2686 / Fax 401 942-0920 6 Europe Tel +31-45-5439343 / Fax +31-45-5427216 RI-01C Series Dry Reed Switch Model Number Parameters Test Conditions Units RI-01CAA Operating Characteristics Operate Range Release Range Operate Time - including bounce typ. Bounce Time typ. Release Time max Resonant Frequency typ. energization 7-19 3-16 24 AT 24 AT 50 24 AT 9000 Electrical Characteristics Switched Power max Switched Voltage DC max Switched Voltage AC, RMS value max Switched Current DC max Switched Current AC, RMS value max

PDF Datasheet Preview

RI-01C Series Dry Reed Switch

RI-01C Series Pico dry-reed switch hermetically sealed in a gas-filled glass envelope. Single-pole, single-throw SPST type, having normally open contacts, and containing two magnetically actuated reeds.

The switch is of the double-ended type and may be actuated by an electromagnet, a permanent magnet or a combination of both.

The device is intended for use in relays, sensors, pulse counters or similar devices.

RI-01C Series Features Ideal for general purpose reed relays and sensors Contact layers Ruthenium on gold Superior glass-to-metal seal and blade alignment

General data for all models RI-01C

Dimensions in inches mm

AT-Customization / Preformed Leads

Besides the standard models, customized products can also be supplied offering the following options ! Operate and release ranges to customer specification ! Cropped and/or preformed leads

Release time > 2ms latching or contact sticking . Loaded conditions resistive load 12V 4 mA 15 mA peak operating frequency 170 Hz

Life expectancy min. 106 operations

Coils

All characteristics are measured using the Philips Standard Coil. For definitions of the Philips Standard Coil, refer to “Application Notes” in the Reed Switch Technical & Application Information Section of this catalog.

End of life criteria Contact resistance > after 4 ms Release time > ms latching or contact sticking .

Switching different loads involves different life expectancy and reliability data. Further information is available on request.

Life expectancy and reliability The life expectancy data given below are valid for a coil energized at times the published maximum operate value for each type in the RI-01C series.

Mechanical Data Contact arrangement is normally open lead finish is tinned net mass is approximately 100 mg and can be mounted in any position.

No-load conditions operating frequency 100 Hz Life expectancy min. 108 operations with a failure rate of less than 10-9 with a confidence level of

Shock The switches are tested in accordance with “IEC 68-227”, test Ea peak acceleration 150 G, half sinewave;

End of life criteria Contact resistance > after 2 ms
duration 11 ms . Such a shock will not cause an open switch no magnetic field present to close, nor a switch
116 COTO TECHNOLOGY USA Tel 401 943-2686 / Fax 401 942-0920 6 Europe Tel +31-45-5439343 / Fax +31-45-5427216

RI-01C Series Dry Reed Switch

Model Number Parameters

Test Conditions Units

RI-01CAA

Operating Characteristics

Operate Range Release Range Operate Time - including bounce typ. Bounce Time typ. Release Time max Resonant Frequency typ.
energization
7-19
3-16
24 AT
24 AT
50 24 AT
9000

Electrical Characteristics

Switched Power max

Switched Voltage DC max

Switched Voltage AC, RMS value max

Switched Current DC max

Switched Current AC, RMS value max

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived RI-01CA Datasheet file may be downloaded here without warranties.

Datasheet ID: RI-01CA 506916