CS3302-ISZR

CS3302-ISZR Datasheet

CS3302

Part	Datasheet
CS3302-ISZR	CS3302-ISZR (pdf)

Related Parts	Information
CS3302-ISZ	CS3302-ISZ

PDF Datasheet Preview
CS3302 High-Z, Programmable Gain, Differential Amplifier Features & Description z Signal Bandwidth DC to 2 kHz z Selectable Gain x1, x2, x4, x8, x16, x32, x64 z Differential Inputs, Differential Outputs • Multiplexed inputs INA, INB, termination • Rough / fine charge outputs for CS5371/72 • Max signal amplitude 5 Vpp differential • Ultra-low input bias < 1 pA z Excellent Noise Performance • 1 µVp-p between Hz and 10 Hz • nV/ from 200 Hz to 2 kHz z Low Total Harmonic Distortion • -118 dB THD typical • -112 dB THD maximum z Low Power Consumption • Normal / LPWR / PWDN 5 mA, mA, 10 µA z Single or Dual Power Supply Configurations • VA+ = +5 V VA- = 0 V VD = V to +5 V • VA+ = V VA- = V VD = V The CS3302 is a high-input-impedance, differential input, differential output amplifier with programmable gain, optimized for amplifying signals from high-impedance sensors such as hydrophones. The gain settings are binary weighted x1, x2, x4, x8, x16, x32, x64 and are selected using simple pin settings. Two sets of external inputs, INA and INB, simplify system design as inputs from a sensor and test DAC. An internal termination can also be selected for noise tests. Amplifier input impedance is very high, requiring less than 1 pA of input current. Noise performance is very good at 1 µVp-p between Hz and 10 Hz, and a noise density of nV/ over the 200 Hz to 2 kHz bandwidth. Distortion performance is also extremely good, typically -118 dB THD. Low input current, low noise, and low total harmonic distortion make this amplifier ideal for high-impedance differential sensors requiring maximum dynamic range. ORDERING INFORMATION See page INA+ INB+ MUX0 MUX1 INAINB- GUARD 56040 OUTR+ OUTF+ 56040 GAIN0 GAIN1 GAIN2 560400 OUTF- OUTR- 56040 LPWR PWDN DGND Copyright Cirrus Logic, Inc. 2007 All Rights Reserved DEC ‘07 DS596F3 CS3302 TABLE OF CONTENTS CHARACTERISTICS AND 4 SPECIFIED OPERATING CONDITIONS 4 ABSOLUTE MAXIMUM RATINGS 4 THERMAL CHARACTERISTICS 5 ANALOG CHARACTERISTICS 5 DIGITAL CHARACTERISTICS 8 POWER SUPPLY CHARACTERISTICS 9 GENERAL 10 Analog Signals 10 2.2.1.Analog Inputs 10 2.3.2.Analog 10 2.4.3.Differential Signals 11 2.5.4.Guard 11 Digital 11 2.7.1.Gain Selection 11 2.8.2.Mux Selection 11 2.9.3.Low Power Selection 11 2.10.4.Power Down Selection 11 Power Supplies 11 2.12.1.Analog Power Supplies 11 2.13.2.Digital Power Supplies 12 Connection 13 PIN DESCRIPTION 14 ORDERING INFORMATION 15 ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION............................ 15 PACKAGE DIMENSIONS 16 DS596F3 CS3302 LIST OF FIGURES Figure CS3302 Noise Performance 5 Figure Digital Input Rise and Fall Times 8 Figure System 10 Figure CS3302 Amplifier Connections 13 Figure CS3302 Pin Assignments 14 LIST OF TABLES Table Digital Selection for Gain and Input Mux Control 8 Table Pin Descriptions 14 Date JUL 2003 AUG 2005 SEP 2005 DEC 2007 Changes Final preliminary release. Updated legal notice. Added MSL data. Updated anti-alias resistor values, relative gain accuracy, input voltage noise, and CS4373A part number. Added watermark to indicate device is not recommended for new designs. Contacting Cirrus Logic Support For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find one nearest you go to IMPORTANT NOTICE Cirrus Logic, Inc. and its subsidiaries “Cirrus” believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided “AS IS” without warranty of any kind express or implied . Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE “CRITICAL APPLICATIONS” . CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. DS596F3 CS3302 CHARACTERISTICS AND SPECIFICATIONS • Min/Max characteristics and specifications are guaranteed over the Specified Operating Conditions. • Typical performance characteristics and specifications are derived from measurements taken at nom- inal supply voltages and TA = 25°C. • DGND = 0 V, all voltages with respect to 0 V. SPECIFIED OPERATING CONDITIONS Parameter Unipolar Power Supplies Positive Analog Negative Analog Positive Digital Bipolar Power Supplies Positive Analog Negative Analog Positive Digital Thermal Ambient Operating Temperature VA+ Note 1 VA Note 2 VD VA+ Note 1 VA Note 2 VD Industrial -IS, -ISZ TA Max Unit Notes VA- must be the most negative voltage to avoid potential SCR latch-up conditions. VD must conform to Digital Supply Differential under Absolute Maximum Ratings. ABSOLUTE MAXIMUM RATINGS CS3302 Parameter Unit DC Power Supplies Positive Analog VA+ Negative Analog VA- Digital VD Analog Supply Differential [ VA+ - VA- ] VADIFF Digital Supply Differential [ VD - VA- ] VDDIFF Input Current, Any Pin Except Supplies ORDERING INFORMATION Model CS3302-IS CS3302-ISZ lead free Temperature -40 to +85 °C CS3302 Package 24-pin SSOP ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION Model Number CS3302-IS CS3302-ISZ lead free Peak Reflow Temp 240 °C 260 °C MSL Rating* 2 3 Max Floor Life 365 Days 7 Days * MSL Moisture Sensitivity Level as specified by IPC/JEDEC J-STD-020. DS596F3 CS3302 PACKAGE DIMENSIONS 24 PIN SSOP PACKAGE DRAWING SIDE VIEW SEATING PLANE END VIEW TOP VIEW INCHES MILLIMETERS NOTE 2,3 1 Notes “D” and “E1” are reference datums and do not included mold flash or protrusions, but do include mold mismatch and are measured at the parting line, mold flash or protrusions shall not exceed mm per side. Dimension “b” does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be mm total in excess of “b” dimension at maximum material condition. Dambar intrusion shall not reduce dimension “b” by more than mm at least material condition. These dimensions apply to the flat section of the lead between and mm from lead tips. DS596F3

PDF Datasheet Preview

CS3302

High-Z, Programmable Gain, Differential Amplifier

Features & Description
z Signal Bandwidth DC to 2 kHz
z Selectable Gain x1, x2, x4, x8, x16, x32, x64
z Differential Inputs, Differential Outputs
• Multiplexed inputs INA, INB, termination
• Rough / fine charge outputs for CS5371/72
• Max signal amplitude 5 Vpp differential
• Ultra-low input bias < 1 pA
z Excellent Noise Performance
• 1 µVp-p between Hz and 10 Hz
• nV/ from 200 Hz to 2 kHz
z Low Total Harmonic Distortion
• -118 dB THD typical
• -112 dB THD maximum
z Low Power Consumption
• Normal / LPWR / PWDN 5 mA, mA, 10 µA
z Single or Dual Power Supply Configurations
• VA+ = +5 V VA- = 0 V VD = V to +5 V
• VA+ = V VA- = V VD = V

The CS3302 is a high-input-impedance, differential input, differential output amplifier with programmable gain, optimized for amplifying signals from high-impedance sensors such as hydrophones. The gain settings are binary weighted x1, x2, x4, x8, x16, x32, x64 and are selected using simple pin settings. Two sets of external inputs, INA and INB, simplify system design as inputs from a sensor and test DAC. An internal termination can also be selected for noise tests.

Amplifier input impedance is very high, requiring less than 1 pA of input current. Noise performance is very
good at 1 µVp-p between Hz and 10 Hz, and a noise
density of nV/ over the 200 Hz to 2 kHz bandwidth. Distortion performance is also extremely good, typically -118 dB THD. Low input current, low noise, and low total harmonic distortion make this amplifier ideal for high-impedance differential sensors requiring maximum dynamic range.
ORDERING INFORMATION

See page

INA+ INB+

MUX0 MUX1

INAINB-

GUARD
56040

OUTR+

OUTF+
56040

GAIN0 GAIN1 GAIN2
560400

OUTF-

OUTR-
56040

LPWR PWDN DGND

Copyright Cirrus Logic, Inc. 2007 All Rights Reserved

DEC ‘07 DS596F3

CS3302

TABLE OF CONTENTS

CHARACTERISTICS AND 4 SPECIFIED OPERATING CONDITIONS 4 ABSOLUTE MAXIMUM RATINGS 4 THERMAL CHARACTERISTICS 5 ANALOG CHARACTERISTICS 5 DIGITAL CHARACTERISTICS 8 POWER SUPPLY CHARACTERISTICS 9

GENERAL 10 Analog Signals 10 2.2.1.Analog Inputs 10 2.3.2.Analog 10 2.4.3.Differential Signals 11 2.5.4.Guard 11 Digital 11 2.7.1.Gain Selection 11 2.8.2.Mux Selection 11 2.9.3.Low Power Selection 11 2.10.4.Power Down Selection 11 Power Supplies 11 2.12.1.Analog Power Supplies 11 2.13.2.Digital Power Supplies 12 Connection 13
PIN DESCRIPTION 14 ORDERING INFORMATION 15 ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION............................ 15 PACKAGE DIMENSIONS 16

DS596F3

CS3302

LIST OF FIGURES

Figure CS3302 Noise Performance 5 Figure Digital Input Rise and Fall Times 8 Figure System 10 Figure CS3302 Amplifier Connections 13 Figure CS3302 Pin Assignments 14

LIST OF TABLES

Table Digital Selection for Gain and Input Mux Control 8 Table Pin Descriptions 14

Date JUL 2003 AUG 2005 SEP 2005

DEC 2007

Changes Final preliminary release. Updated legal notice. Added MSL data. Updated anti-alias resistor values, relative gain accuracy, input voltage noise, and CS4373A part number. Added watermark to indicate device is not recommended for new designs.

Contacting Cirrus Logic Support

For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find one nearest you go to

IMPORTANT NOTICE

Cirrus Logic, Inc. and its subsidiaries “Cirrus” believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided “AS IS” without warranty of any kind express or implied . Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale.

CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE “CRITICAL APPLICATIONS” . CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES.

Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners.

DS596F3

CS3302

CHARACTERISTICS AND SPECIFICATIONS
• Min/Max characteristics and specifications are guaranteed over the Specified Operating Conditions.
• Typical performance characteristics and specifications are derived from measurements taken at nom-
inal supply voltages and TA = 25°C.
• DGND = 0 V, all voltages with respect to 0 V.

SPECIFIED OPERATING CONDITIONS

Parameter Unipolar Power Supplies Positive Analog Negative Analog Positive Digital Bipolar Power Supplies Positive Analog Negative Analog Positive Digital Thermal Ambient Operating Temperature

VA+ Note 1 VA Note 2 VD

VA+ Note 1 VA Note 2 VD

Industrial -IS, -ISZ TA

Max Unit

Notes VA- must be the most negative voltage to avoid potential SCR latch-up conditions. VD must conform to Digital Supply Differential under Absolute Maximum Ratings.

ABSOLUTE MAXIMUM RATINGS

CS3302

Parameter

Unit

DC Power Supplies

Positive Analog VA+

Negative Analog VA-

Digital VD

Analog Supply Differential [ VA+ - VA- ]

VADIFF

Digital Supply Differential [ VD - VA- ]

VDDIFF

Input Current, Any Pin Except Supplies
ORDERING INFORMATION

Model CS3302-IS CS3302-ISZ lead free

Temperature -40 to +85 °C

CS3302

Package 24-pin SSOP

ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION

Model Number CS3302-IS CS3302-ISZ lead free

Peak Reflow Temp 240 °C 260 °C

MSL Rating* 2 3

Max Floor Life 365 Days 7 Days
* MSL Moisture Sensitivity Level as specified by IPC/JEDEC J-STD-020.

DS596F3

CS3302

PACKAGE DIMENSIONS 24 PIN SSOP PACKAGE DRAWING

SIDE VIEW

SEATING PLANE

END VIEW

TOP VIEW

INCHES

MILLIMETERS

NOTE
2,3 1

Notes “D” and “E1” are reference datums and do not included mold flash or protrusions, but do include mold mismatch and are measured at the parting line, mold flash or protrusions shall not exceed mm per side.

Dimension “b” does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be mm total in excess of “b” dimension at maximum material condition. Dambar intrusion shall not reduce dimension “b” by more than mm at least material condition.

These dimensions apply to the flat section of the lead between and mm from lead tips.

DS596F3

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived CS3302-ISZR Datasheet file may be downloaded here without warranties.

Datasheet ID: CS3302-ISZR 523154