MINI-UHF-16

MINI-UHF-16 Datasheet

Mini-UHF Straight Crimp Type Plug -

Part	Datasheet
MINI-UHF-16	MINI-UHF-16 (pdf)

PDF Datasheet Preview
INCHES MILLIMETERS CUSTOMER DRAWINGS AVAILABLE UPON REQUEST Mini-UHF Straight Crimp Type Plug - Solder or Crimp Contact PART NUMBER CABLE TYPE MINI-UHF-16 PROFLEX RG-450 “A” CONTACT I.D. BODY I.D. FERRULE I.D. Identify connector parts. 4 piece parts Slide heat shrink as applicable and crimp sleeve onto jacket of cable. Strip cable to dimensions shown. Do not nick braid or center conductor. Tin center conductor if contact will be solder attached. Do not tin center conductor if contact is to be crimp attached. A wire stripper of correct size is recommended for this step. Assemble contact onto cable as shown. Solder Attachment Solder contact to center conductor through hole using a minimum amount of solder for a good joint. Crimp Attachment where applicable Crimp contact to center conductor using recommended crimp tool. Slide coupling nut onto the connector body. Flare braid and slide body assembly over contact and under braid as shown. Then seat body assembly firmly onto contact until a gentle snap is felt, indicating the contact is in place. The cable may have to be held in a clamping fixture. Arrange braid uniformly around crimp stem. Slide crimp sleeve forward and crimp using recommended crimp tool. Slide heat shrink forward and shrink as applicable . Part Number MINI-UHF-16 Cable Contact I.D. RG-450, Proflex Body I.D. Ferrule I.D. Crimp Braid Hex Contact Recommended Crimp Hex Crimp Tool 24-305P Cambridge Products, P.O. Box 1732, Waseca, MN 56093-0832 • 1-800-243-8814 • Fax 507-833-6287 • Mini-UHF Connectors Specifications INCHES MILLIMETERS CUSTOMER DRAWINGS AVAILABLE UPON REQUEST Mini UHF connectors are low cost, general purpose units designed for low frequency system applications. These commercial quality connectors are equipped with threaded coupling interfaces for secure and reliable connections. The Standard UHF and Mini UHF connectors are not intermateable. Specifications* MINI UHF Electrical Characteristics Impedance Nonconstant Frequency range 0-2 GHz Working voltage 500 volts RMS at sea level Dielectric withstanding voltage 1500 volts RMS at sea level Insulation resistance 5000 megohms minimum Environmental Characteristics Recommended temperature range -55OC to +85OC Mechanical Characteristics Durability 500 cycles Cable retention 20 lbs., RG-58 C/U cable Materials Body and coupling nut Zinc or brass Contact Brass Crimp Sleeve Brass Insulator TPX Polymethylpetene Plating Body - Nickel Crimp sleeve - Nickel Contact - Gold * These values are typical and may not apply to all connectors. Cambridge Products, P.O. Box 1732, Waseca, MN 56093-0832 • 1-800-243-8814 • Fax 507-833-6287 •

PDF Datasheet Preview

INCHES MILLIMETERS CUSTOMER DRAWINGS AVAILABLE UPON REQUEST

Mini-UHF Straight Crimp Type Plug -

Solder or Crimp Contact

PART NUMBER CABLE TYPE MINI-UHF-16 PROFLEX RG-450
“A”

CONTACT I.D. BODY I.D. FERRULE I.D.

Identify connector parts. 4 piece parts

Slide heat shrink as applicable and crimp sleeve onto jacket of cable. Strip cable to dimensions shown. Do not nick braid or center conductor. Tin center conductor if contact will be solder attached. Do not tin center conductor if contact is to be crimp attached. A wire stripper of correct size is recommended for this step.

Assemble contact onto cable as shown. Solder Attachment Solder contact to center conductor through hole using a minimum amount of solder for a good joint. Crimp Attachment where applicable Crimp contact to center conductor using recommended crimp tool.

Slide coupling nut onto the connector body.

Flare braid and slide body assembly over contact and under braid as shown. Then seat body assembly firmly onto contact until a gentle snap is felt, indicating the contact is in place. The cable may have to be held in a clamping fixture. Arrange braid uniformly around crimp stem. Slide crimp sleeve forward and crimp using recommended crimp tool. Slide heat shrink forward and shrink as applicable .

Part Number MINI-UHF-16

Cable

Contact I.D.

RG-450, Proflex

Body I.D.

Ferrule I.D.

Crimp Braid Hex

Contact Recommended Crimp Hex Crimp Tool
24-305P

Cambridge Products, P.O. Box 1732, Waseca, MN 56093-0832
• 1-800-243-8814
• Fax 507-833-6287
•

Mini-UHF Connectors

Specifications

INCHES MILLIMETERS CUSTOMER DRAWINGS AVAILABLE UPON REQUEST

Mini UHF connectors are low cost, general purpose units designed for low frequency system applications. These commercial quality connectors are equipped with threaded coupling interfaces for secure and reliable connections. The Standard UHF and Mini UHF connectors are not intermateable.

Specifications*

MINI UHF Electrical Characteristics Impedance Nonconstant Frequency range 0-2 GHz Working voltage 500 volts RMS at sea level Dielectric withstanding voltage 1500 volts RMS at sea level Insulation resistance 5000 megohms minimum

Environmental Characteristics Recommended temperature range -55OC to +85OC

Mechanical Characteristics Durability 500 cycles Cable retention 20 lbs., RG-58 C/U cable

Materials Body and coupling nut Zinc or brass Contact Brass Crimp Sleeve Brass Insulator TPX Polymethylpetene Plating Body - Nickel

Crimp sleeve - Nickel Contact - Gold
* These values are typical and may not apply to all connectors.

Cambridge Products, P.O. Box 1732, Waseca, MN 56093-0832
• 1-800-243-8814
• Fax 507-833-6287
•

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MINI-UHF-16 Datasheet file may be downloaded here without warranties.

Datasheet ID: MINI-UHF-16 522685