VMMK-3603-TR2G

VMMK-3603-TR2G Datasheet

VMMK-3603 1 - 6 GHz Positive Gain Slope Low Noise Amplifier in SMT Package

Part	Datasheet
VMMK-3603-TR2G	VMMK-3603-TR2G (pdf)

PDF Datasheet Preview
VMMK-3603 1 - 6 GHz Positive Gain Slope Low Noise Amplifier in SMT Package Data Sheet WLP0402, 1 mm x mm x mm • 1 x mm surface mount package • Ultrathin mm • Wide frequency range 1 to 6 GHz • Low noise figure • Positive gain slope • Self-Biasing 3 to 5 V Specifications 5 GHz, Vdd = 5 V, Zin = Zout = 50 • Small signal gain 17 dB typ. • Noise Figure = dB typ. • Output 3rd Order Intercept Point = 25 dBm • and 5-6 GHz WLAN and WiMax • & BWA systems • Radar and ECM systems • Generic IF amplifier Pin Connections Top View Input Output Input Note “M” = Device Code “Y” = Month Code Output Attention Observe precautions for handling electrostatic sensitive devices. ESD Machine Model = 50 V ESD Human Body Model = 300 V Refer to Avago Application Note A004R Electrostatic Discharge, Damage and Control. Electrical Specifications Table Absolute Maximum Rating [1] Parameters/Condition Unit Absolute Max Supply Voltage RF Output [2] Supply Current [2] Pin, max CW RF Input Power RF Input [3] Pdiss Total Power Dissipation Max Channel Temperature +150 Thermal Resistance [4] °C/W Notes Operation of this device above any one of these parameters may cause permanent damage Bias is assumed DC quiescent conditions With the DC typical bias and RF applied to the device at board temperature Tb = 25° C Thermal resistance is measured from junction to board using IR method Table DC and RF Specifications [1] TA = 25° C, Vd = 5 V, Freq = 5 GHz, Zin = Zout = 50 unless otherwise specified Parameters/Condition Unit Minimum Id [2] Supply Current NF [2,3] Noise Figure Ga [2,3] Associated Gain S11 [4] Ordering Information Part Number VMMK-3603-BLKG VMMK-3603-TR1G Devices Per Container 100 5000 Container Antistatic Bag 7” Reel Package Dimension Outline A Note All dimensions are in mm Dimensions Symbol E Min mm Max mm Reel Orientation REEL Device Orientation USER FEED DIRECTION USER FEED DIRECTION CARRIER TAPE • MY • MY • MY • MY TOP VIEW Notes “M” = Device Code “Y” = Month Code 8 mm END VIEW E F Note 2 W Bo Scale 5:1 SECTION Tape Dimensions Note 2 Note 1 T 5° Max A R0.1 5° Max Scale 5:1 SECTION Unit mm Symbol K1 Po P1 P2 Do D1 E F 10Po W T Spec. Ao = mm Bo = mm Notice 10 Sprocket hole pitch cumulative tolerance is mm. Pocket position relative to sprocket hole measured as true position of pocket not pocket hole. Ao & Bo measured on a place mm above the bottom of the pocket to top surface of the carrier. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier. Carrier camber shall be not than 1 m per 100 mm through a length of 250 mm. For product information and a complete list of distributors, please go to our web site:

PDF Datasheet Preview

VMMK-3603 1 - 6 GHz Positive Gain Slope Low Noise Amplifier in SMT Package

Data Sheet

WLP0402, 1 mm x mm x mm
• 1 x mm surface mount package
• Ultrathin mm
• Wide frequency range 1 to 6 GHz
• Low noise figure
• Positive gain slope
• Self-Biasing 3 to 5 V

Specifications 5 GHz, Vdd = 5 V, Zin = Zout = 50
• Small signal gain 17 dB typ.
• Noise Figure = dB typ.
• Output 3rd Order Intercept Point = 25 dBm
• and 5-6 GHz WLAN and WiMax
• & BWA systems
• Radar and ECM systems
• Generic IF amplifier

Pin Connections Top View

Input

Output

Input

Note “M” = Device Code “Y” = Month Code

Output

Attention Observe precautions for handling electrostatic sensitive devices. ESD Machine Model = 50 V ESD Human Body Model = 300 V Refer to Avago Application Note A004R Electrostatic Discharge, Damage and Control.

Electrical Specifications

Table Absolute Maximum Rating [1]

Parameters/Condition

Unit

Absolute Max

Supply Voltage RF Output [2]

Supply Current [2]

Pin, max

CW RF Input Power RF Input [3]

Pdiss

Total Power Dissipation

Max Channel Temperature
+150

Thermal Resistance [4]
°C/W

Notes Operation of this device above any one of these parameters may cause permanent damage Bias is assumed DC quiescent conditions With the DC typical bias and RF applied to the device at board temperature Tb = 25° C Thermal resistance is measured from junction to board using IR method

Table DC and RF Specifications [1] TA = 25° C, Vd = 5 V, Freq = 5 GHz, Zin = Zout = 50 unless otherwise specified

Parameters/Condition

Unit

Minimum

Id [2]

Supply Current

NF [2,3]

Noise Figure

Ga [2,3]

Associated Gain

S11 [4]
Ordering Information

Part Number VMMK-3603-BLKG VMMK-3603-TR1G

Devices Per Container 100
5000

Container Antistatic Bag 7” Reel

Package Dimension Outline

A Note All dimensions are in mm

Dimensions Symbol E

Min mm

Max mm

Reel Orientation

REEL

Device Orientation

USER FEED DIRECTION

USER FEED DIRECTION

CARRIER TAPE
• MY
• MY
• MY
• MY

TOP VIEW

Notes “M” = Device Code “Y” = Month Code
8 mm END VIEW

E F Note 2 W Bo Scale 5:1

SECTION

Tape Dimensions

Note 2

Note 1

T 5° Max

A R0.1
5° Max

Scale 5:1

SECTION

Unit mm

Symbol K1 Po P1 P2 Do D1 E F 10Po W T

Spec.

Ao = mm

Bo = mm

Notice 10 Sprocket hole pitch cumulative tolerance is mm. Pocket position relative to sprocket hole measured as true position
of pocket not pocket hole. Ao & Bo measured on a place mm above the bottom of the
pocket to top surface of the carrier. Ko measured from a plane on the inside bottom of the pocket to
the top surface of the carrier. Carrier camber shall be not than 1 m per 100 mm through a length
of 250 mm.

For product information and a complete list of distributors, please go to our web site:

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived VMMK-3603-TR2G Datasheet file may be downloaded here without warranties.

Datasheet ID: VMMK-3603-TR2G 520534