HFCT-5911QTLZ

HFCT-5911QTLZ Datasheet


HFCT-5911ATLZ Single Mode Laser Transceivers for Gigabit Ethernet and iSCSI Applications at Gb/s

Part Datasheet
HFCT-5911QTLZ HFCT-5911QTLZ HFCT-5911QTLZ (pdf)
Related Parts Information
HFCT-5911ATLZ HFCT-5911ATLZ HFCT-5911ATLZ
PDF Datasheet Preview
HFCT-5911ATLZ Single Mode Laser Transceivers for Gigabit Ethernet and iSCSI Applications at Gb/s

Data Sheet

The HFCT-5911ATLZ transceiver is a high performance, cost effective module for serial optical data communications applications operating at Gb/s. This module is designed for single mode fiber and operates at a nominal wavelength of 1310 nm. It incorporates high performance, reliable, long wavelength optical devices and proven circuit technology to give long life and consistent service.

The transmitter section incorporates a 1310 nm Fabry Perot FP laser. The transmitter has full IEC 825 and CDRH Class 1 eye safety.

The receiver section uses an MOVPE grown planar SEDET PIN photo detector for low dark current and excellent responsivity.

The transceiver is supplied in the industry standard 2 x 5 DIP style package with the LC fiber connector interface and is footprint compatible with SFF Multi Source Agreement MSA .
• 10 km Links with 9/125 µm single mode fiber SMF
• 550 m Links in µm multi mode fiber MMF
• Compliant to IEEE 2000 Edition
• Compliant to Small Form Factor MSA specifications
• 2 x 5 package style with LC receptacle
• Single V power supply
• Case operating temperature range -10°C to +85°C
• Manufactured in an ISO9002 certified facility
• Fully Class 1 CDRH/IEC 825 compliant
• Wave solder and aqueous wash process compatible
• RoHS Compliance
• Gigabit Ethernet 1000BASE-LX
• High speed links for Gigabit Ethernet
• Switches
• Routers
• Hubs

Functional Description Receiver Section

Design

The receiver section for the HFCT-5911ATLZ contains an InGaAs/InP photo detector and a pre-amplifier mounted in an optical subassembly. This optical subassembly is coupled to a post-amplifier/decision circuit on a circuit board. The design of the optical assembly is such that it provides better than 12 dB Optical Return Loss ORL .

The post-amplifier is ac coupled to the pre-amplifier as illustrated in Figure The coupling capacitors are capable of passing the Gigabit Ethernet test pattern at Gb/s without any significant distortion or performance penalty. If a lower signal rate, or a code which has significantly more low frequency content is used, sensitivity, jitter and pulse distortion could be degraded.

Figure 1 also shows a filter function which limits the bandwidth of the pre-amplifier output signal. The filter is designed to bandlimit the pre-amplifier output noise and thus improve the receiver sensitivity.

These components will reduce the sensitivity of the receiver as the signal bit rate is increased above Gb/s.

Noise Immunity

The receiver includes internal circuit components to filter power supply noise. However under some conditions of EMI and power supply noise, external power supply filtering may be necessary see Application Section .

The Signal Detect Circuit

The signal detect circuit works by sensing the peak level of the received signal and comparing this level to a reference. The SD output is low voltage TTL.

TRANSIMPEDANCE PREAMPLIFIER

FILTER

AMPLIFIER

PECL OUTPUT BUFFER

DATA OUT DATA OUT

GND Figure Receiver Block Diagram

SIGNAL DETECT

TTL OUTPUT

CIRCUIT

BUFFER

Functional Description Transmitter Section

Design

A schematic diagram for the transmitter is shown in Figure The HFCT-5911ATLZ incorporates an FP laser and has been designed to be compliant with IEC 825 eye safety requirements under any single fault condition and CDRH under normal operating conditions. The optical output is controlled by a custom IC that detects the laser output via the monitor photodiode. This IC provides both dc and ac current drive to the laser to ensure correct modulation, eye diagram and extinction ratio over temperature, supply voltage and operating life.

DATA

PECL INPUT

LASER MODULATOR

FP LASER

PHOTODIODE rear facet monitor

LASER BIAS DRIVER

Figure Simplified Transmitter Schematic

LASER BIAS CONTROL

Package

The overall package concept for the device consists of the following basic elements two optical subassemblies, two electrical subassemblies and the housing as illustrated in the block diagram in
Ordering Information
1310 nm FP Laser Case Temperature range -10°C to +85°C

HFCT-5911ATLZ

Related Products

Other single mode Gigabit Ethernet transceivers in this product family are:

HFCT-5914ATLZ 2x10 DIP

Class 1 Laser Product This product conforms to the
applicable requirements of 21 CFR 1040 at the date of manufacture Date of Manufacture Avago Technologies Inc., No 1 Yishun Ave 7, Singapore

Handling Precautions

The HFCT-5911ATLZ can be damaged by current surges or overvoltage. Power supply transient precautions should be taken.

Normal handling precautions for electrostatic sensitive devices should be taken.

For product information and a complete list of distributors, please go to our web site:

Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries. Data subject to change. Copyright 2006 Avago Technologies Pte. All rights reserved. 5989-4181EN - July 17, 2006
More datasheets: GPC40-3.3G | GPC40-12G | GPC40-24G | GPC40DG | 220-4842-00-3303 | 240-4846-00-3303 | 18475USA | FMG2G150US60E | CDB42L55 | HFCT-5911ATLZ


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HFCT-5911QTLZ Datasheet file may be downloaded here without warranties.

Datasheet ID: HFCT-5911QTLZ 520319