HFBR-2505A

HFBR-2505A Datasheet


HFBR-1505A/2505A Fiber Optic Transmitters and Receivers for Fieldbus Applications

Part Datasheet
HFBR-2505A HFBR-2505A HFBR-2505A (pdf)
Related Parts Information
HFBR-1505A HFBR-1505A HFBR-1505A
HFBR-1505C HFBR-1505C HFBR-1505C
HFBR-1515B HFBR-1515B HFBR-1515B
HFBR-2505C HFBR-2505C HFBR-2505C
PDF Datasheet Preview
HFBR-1505A/2505A Fiber Optic Transmitters and Receivers for Fieldbus Applications

Data Sheet

HFBR-1505A/2505A SMA Tx/Rx for SERCOS HFBR-1515B/2515B Tx/Rx for PROFIBUS HFBR-1505C/2505C SMA Tx/Rx for INTERBUS-S

SERCOS

SERCOS, an acronym for SErial Realtime COmmunications System, is a standard digital interface for communication in industrial CNC applications. SERCOS is a European EN 61491 and international standard IEC The optical interface allows data rates of 2, 4, 8, and 16 MBd and data transfer between numerical controls and drives via fiber-optic rings, with voltage isolation and noise immunity. The HFBR-1505A and HFBR-2505A products comply with SERCOS specifications for optical characteristics and connector style, and have guaranteed performance up to 10 MBd. Typically the 16 MBd required by SERCOS is possible as well but please contact Avago regarding the plan for the 16 MBd device.

PROFIBUS

PROFIBUS, an acronym of PROcess FIeld BUS, is an open fieldbus standard defined for data rates ranging from kBd to12 MBd in selectable steps for wire and optical fiber. PROFIBUS is a German national DIN 19245 standard and a European CENELEC standard EN The connector is the recommended optical port of the PROFIBUS optical fiber version but other connectors are allowed as well. The HFBR-1515B and HFBR-2515B comply fully to the technical guideline using Plastic Optical Fiber up to 6 MBd, and have a guaranteed performance at data rates up to 10 MBd. Typically the 12 MBd is possible as well, but please contact Avago regarding the plan for the 12 MBd device.

Features
• Meets industrial SERCOS, PROFIBUS, and INTERBUS-S
standard
• SMA and ports
• 650 nm wavelength technology
• Specified for use with 1 mm plastic optical fiber and
200 µm hard clad silica
• Auto-insertable and wave solderable
• DC 10 MBd data rate

Applications
• Industrial control data links
• Factory automation data links
• Voltage isolation applications
• PLCs
• Motor drives
• Sensor, meter and actuator interfaces

INTERBUS-S

INTERBUS-S, a special open Sensor/Actuator Bus, is finding a broad acceptance in the factory automation industry. The HFBR-1505C and HFBR-2505C were specially designed for this application and can be used with 1 mm POF and 200 µm HCS fiber at the specified data rates of 500 kBd and 2 MBd.
is a registered trademark of AT&T. is a registered trademark of SpecTran Corporation.

The optical transmission guideline is a supplement of the German National DIN E 19258 standard draft. On the European level, prEN 50254 is the draft of the INTERBUS-S fieldbus.

Package Information

All HFBR-X5X5X series transmitters and receivers are housed in a low-cost, dual-in-line package that is made of high strength, heat resistant, chemically resistant and UL 94 V-O UL file # E121562 flame retardant plastic. The transmitters are easily identified by the light grey colored connector port. The receivers are
easily identified by the dark grey colored connector port. The package is designed for autoinsertion and wave soldering so it is ideal for high volume production applications.

Handling and Design Information

When soldering, it is advisable to leave the protective cap on the unit to keep the optics clean. Good system performance requires clean port optics and cable ferrules to avoid obstructing the optical path. Clean compressed air often is sufficient to remove particles of dirt methanol on a cotton swab also works well.

Recommended Chemicals for Cleaning/Degreasing X5X5X Products

Alcohols methyl, isopropyl, isobutyl. Aliphatics hexane, heptane. Other soap solution, naphtha.

Do not use partially halogenated hydrocarbons such as 1,1,1 trichloroethane, ketones such as MEK, acetone, chloroform, ethyl acetate, methylene dichloride, phenol, methylene chloride or N-methylpyrolldone. Also, Avago does not recommend the use of cleaners that use halogenated hydrocarbons because of their potential environmental harm.

CAUTION The small junction size inherent in the design of these components increases the components’ susceptibility to damage from electrostatic discharge ESD . It is advised that normal static precautions be taken in handling and assembly of these components to prevent damage and/or degradation which may be induced by ESD.

Specified Link Performance to unless otherwise noted.

Parameter

Symbol Min. Max. Unit

Condition

Reference

Link Distance with HFBR-1505A/2505A or HFBR-1515B/2515B

Notes 1,2,3,4,6 Notes 1,2,3,5,6

Link Distance with HFBR-1505C/2505C

Notes 1,2,3,4,7 Notes 1,2,3,5,7

Pulse Width Distortion
with HFBR-1505A/2505A
or HFBR-1515B/2515B
25% to 75% duty cycle

Note 1

Pulse Width Distortion with HFBR-1505C/2505C
+125
arbitrary duty cycle
More datasheets: HLMP-CB34-R0CDD | HLMP-CM13-Z30DD | 41-40021 | 41-40022 | 41-40023 | ELD-306SYGWA/S530-E2 | HFBR-1505A | HFBR-1505C | HFBR-1515B | HFBR-2505C


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HFBR-2505A Datasheet file may be downloaded here without warranties.

Datasheet ID: HFBR-2505A 520301