HFBR-0534

HFBR-0534 Datasheet

HFBR-0534 Evaluation Kit for Diagnostic Monitoring Interface DMI Small Form Pluggable SFP Transceivers

Part	Datasheet
HFBR-0534	HFBR-0534 (pdf)

PDF Datasheet Preview
HFBR-0534 Evaluation Kit for Diagnostic Monitoring Interface DMI Small Form Pluggable SFP Transceivers For bench top evaluation, the HFBR-0534 is the recommended tool for Avago Technologies new SmallForm-Pluggable SFP transceivers with the Diagnostic Monitoring Interface DMI . The HFBR-0534 includes the necessary two-wire serial interface to communicate with the Diagnostic Monitoring Interface and provides a standard 9 pin serial interface to connect to a PC. A Window’s based Graphical User Interface GUI provides the user an easy, straightforward way to communicate to SFP transceivers. The interface software is customized to allow quick verification of the feature sets defined in the SFF-8472 MSA. The HFBR-0534 requires only one input DC supply voltage 9 V to 12 V to power all board components, including the micro-controller, and both the receiver and transmitter sections of the SFP transceiver. Just plug in the DMI SFP and your ready to go. Using Avago Technologies HFBR-0534 evaluation board kit , the user can then read specific bytes from the SFP’s memory pages decoding into ASCII or HEX , access and log the internal measurements of the transceiver temperature, supply voltage, transmitter bias current, transmitter output power, and received optical power as well as program the device EEPROM. Using a Bit-Error-Ratio Tester BERT and a Digital Communication Analyzer DCA , the HFBR-0534 is also suitable for evaluating the optical characteristics, including the eye diagram, jitter, and rise/fall time and the electrical characteristics, including the receiver electrical eye diagram, jitter, and rise/fall time. • Included in the HFBR-0534 Evaluation Kit: - An evaluation board - Software - 9 pin serial cable - 110 V/220 V power supply • On board potentiometer to adjust the voltage to the SFP for to V • Test points for easy probing of Mod_Def signals, TX_ Fault and LOS signals. • On-board hardware switch for toggling of TX_Disable control signal • Onboard LEDS to monitor the status of : - LOS LED - turns on when LOS hard-signal is asserted by SFP module - Mod_Def 0 LED turns on when a module is present - TX_Fault LED turns on when TX_Fault is asserted by module - TX_disable LED on when TX is enabled, turns off when TX is disabled • GUI software allows easy decoding of 0xA0 and 0xA2 page byte contents per SFF-8472 MSA • GUI sub-window enables quick execution of byte write operations delay between write operations is adjustable • Supports two-wire serial interface 100 kHz • Operating Temperature Range: 0 °C to +50 °C • Bench top evaluation of Avago’s SFP with DMI mod- ules • Logging and Recording of Monitoring Values • Printable Reports of SFP content and decoded infor- mation • Reading and writing to on-board SFP memory • Optical / Electrical testing of all Avago SFP modules Additional Equipment Recommended • Fiber optic cables - LC to SC 1 M and 50/125 µm or µm, 9/125 µm - LC to LC Loopback <1M and 50/125 µm or µm, 9/125 µm • 86100A Agilent Digital Communications Analyzer • Agilent Optical/Electrical DCA Plug-In Module 86101A Option H41 or H21 2125 FC • 86130A Agilent BitAlyzer 3 Gb/s Bit Error Rate Ordering Information Please contact your local field sales engineer or one of Avago Technologies franchised distributors for ordering information. For technical information, please visit Avago’s web page at or contact Avago. Block Diagram Note The electrical loop back and optical loop back cable shown in this diagram provides an emulated signal in the absence of a signal generator for basic verification of RX and TX Monitoring. For product information and a complete list of distributors, please go to our web site Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright 2007 Avago Technologies Limited. All rights reserved. 5988-9573EN - February 23, 2007

PDF Datasheet Preview

HFBR-0534 Evaluation Kit for Diagnostic Monitoring Interface DMI Small Form Pluggable SFP Transceivers

For bench top evaluation, the HFBR-0534 is the recommended tool for Avago Technologies new SmallForm-Pluggable SFP transceivers with the Diagnostic Monitoring Interface DMI . The HFBR-0534 includes the necessary two-wire serial interface to communicate with the Diagnostic Monitoring Interface and provides a standard 9 pin serial interface to connect to a PC.

A Window’s based Graphical User Interface GUI provides the user an easy, straightforward way to communicate to SFP transceivers. The interface software is customized to allow quick verification of the feature sets defined in the SFF-8472 MSA. The HFBR-0534 requires only one input DC supply voltage 9 V to 12 V to power all board components, including the micro-controller, and both the receiver and transmitter sections of the SFP transceiver. Just plug in the DMI SFP and your ready to go. Using Avago Technologies HFBR-0534 evaluation board kit , the user can then read specific bytes from the SFP’s memory pages decoding into ASCII or HEX , access and log the internal measurements of the transceiver temperature, supply voltage, transmitter bias current, transmitter output power, and received optical power as well as program the device EEPROM.

Using a Bit-Error-Ratio Tester BERT and a Digital Communication Analyzer DCA , the HFBR-0534 is also suitable for evaluating the optical characteristics, including the eye diagram, jitter, and rise/fall time and the electrical characteristics, including the receiver electrical eye diagram, jitter, and rise/fall time.
• Included in the HFBR-0534 Evaluation Kit:
- An evaluation board
- Software
- 9 pin serial cable
- 110 V/220 V power supply
• On board potentiometer to adjust the voltage to the

SFP for to V
• Test points for easy probing of Mod_Def signals, TX_

Fault and LOS signals.
• On-board hardware switch for toggling of TX_Disable
control signal
• Onboard LEDS to monitor the status of :
- LOS LED - turns on when LOS hard-signal is asserted by SFP module
- Mod_Def 0 LED turns on when a module is present
- TX_Fault LED turns on when TX_Fault is asserted by module
- TX_disable LED on when TX is enabled, turns off when TX is disabled
• GUI software allows easy decoding of 0xA0 and 0xA2
page byte contents per SFF-8472 MSA
• GUI sub-window enables quick execution of byte write
operations delay between write operations is adjustable
• Supports two-wire serial interface 100 kHz
• Operating Temperature Range:
0 °C to +50 °C
• Bench top evaluation of Avago’s SFP with DMI mod-
ules
• Logging and Recording of Monitoring Values
• Printable Reports of SFP content and decoded infor-
mation
• Reading and writing to on-board SFP memory
• Optical / Electrical testing of all Avago SFP modules

Additional Equipment Recommended
• Fiber optic cables
- LC to SC 1 M and 50/125 µm or µm,
9/125 µm
- LC to LC Loopback <1M and 50/125 µm or
µm, 9/125 µm
• 86100A Agilent Digital Communications Analyzer
• Agilent Optical/Electrical DCA Plug-In Module 86101A

Option H41 or H21 2125 FC
• 86130A Agilent BitAlyzer 3 Gb/s Bit Error Rate
Ordering Information
Please contact your local field sales engineer or one of Avago Technologies franchised distributors for ordering information. For technical information, please visit Avago’s web page at or contact Avago.

Block Diagram

Note The electrical loop back and optical loop back cable shown in this diagram provides an emulated signal in the absence of a signal generator for basic verification of RX and TX Monitoring.

For product information and a complete list of distributors, please go to our web site Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright 2007 Avago Technologies Limited. All rights reserved. 5988-9573EN - February 23, 2007

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HFBR-0534 Datasheet file may be downloaded here without warranties.

Datasheet ID: HFBR-0534 520299