HCPL-3000

HCPL-3000 Datasheet

HCPL-3000 Power Bipolar Transistor Base Drive Optocoupler

Part	Datasheet
HCPL-3000	HCPL-3000 (pdf)

Related Parts	Information
HCPL-3000-300E	HCPL-3000-300E
HCPL-3000-500E	HCPL-3000-500E
HCPL-3000-000E	HCPL-3000-000E

PDF Datasheet Preview
HCPL-3000 Power Bipolar Transistor Base Drive Optocoupler Data Sheet The HCPL-3000 consists of a Silicon-doped GaAs LED optically coupled to an integrated circuit with a power output stage. This optocoupler is suited for driving power bipolar transistors and power Darlington devices used in motor control inverter applications. The high peak and steady state current capabilities of the output stage allow for direct interfacing to the power device without the need for an intermediate amplifier stage. With a CMR rating of 10 kV/µs this optocoupler readily rejects transients found in inverter applications. The LED controls the state of the output stage. Transistor Q2 in the output stage is on with the LED off, allowing the base of the power device to be held low. Turning on the LED turns off transistor Q2 and switches on transistor Q1 in the output stage which provides current to drive the base of a power bipolar device. • High output current IO2 A Peak, A continuous IO1 A Peak, A continuous • 10 kV/µs minimum Common Mode Rejection CMR at VCM = 600 V • Wide VCC range to 13 volts • 2 µs typical propagation delay • Recognized under UL 1577 for dielectric withstand proof test voltage of 5000 vac, 1 minute • Isolated bipolar transistor base drive • AC and DC motor drives • General purpose industrial inverters • Uninterruptable power supply Functional Diagram ANODE 1 CATHODE 2 HCPL-3000 8 VCC 7 GND Q2 6 VO2 Q1 5 VO1 TRUTH TABLE LED OUTPUT Q1 Q2 ON HIGH LEVEL ON OFF OFF LOW LEVEL OFF ON THE USE OF A 0.1µF BYPASS CAPACITOR CONNECTED BETWEEN PINS 8 AND 7 IS RECOMMENDED. ALSO, CURRENT LIMITING RESISTORS ARE RECOMMENDED SEE FIGURE 1, NOTE 2, AND NOTE CAUTION It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. Schematic 1 ANODE CATHODE Q1 I O2 6 VO2 Ordering Information HCPL-3000 is UL Recognized with 5000 Vrms for 1 minute per UL1577. HCPL-3000 Option RoHS Compliant -000E -300E -500E Package 300 mil DIP-8 Surface Mount Gull Wing Tape & Reel Quantity 50 per tube 50 per tube 1000 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1 HCPL-3000-500E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging and RoHS compliant. Example 2 HCPL-3000-000E to order product of 300 mil DIP package in Tube packaging and RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks The notation ‘#XXX’ is used for existing products, while new products launched since July 15, 2001 and RoHS compliant will use Outline Drawing TYPE NUMBER DATE CODE A XXXX YYWW 0° 13° 0° 13° ANODE 1 CATHODE 2 HCPL-3000 8 VCC 7 GND Q2 6 VO2 Q1 5 VO1 Regulatory Information The HCPL-3000 has been approved by the following organizations: Recognized under UL 1577, Component Recognition Program, File E55361. Demonstrated ESD Performance Human Body Model MIL-STD883 Method Class 2 Machine Model EIAJ IC-121 1988 Version 2 , Test Method 20, Condition C 1200 V Insulation and Safety Related Specifications Parameter Min. External Air Gap External Clearance Min. External Tracking Path External Creepage Min. Internal Plastic Gap Internal Clearance Symbol Value Units L IO1 mm L IO2 mm Conditions Shortest distance measured through air, between two conductive leads, input to output

PDF Datasheet Preview

HCPL-3000 Power Bipolar Transistor Base Drive Optocoupler

Data Sheet

The HCPL-3000 consists of a Silicon-doped GaAs LED optically coupled to an integrated circuit with a power output stage. This optocoupler is suited for driving power bipolar transistors and power Darlington devices used in motor control inverter applications. The high peak and steady state current capabilities of the output stage allow for direct interfacing to the power device without the need for an intermediate amplifier stage. With a CMR rating of 10 kV/µs this optocoupler readily rejects transients found in inverter applications.

The LED controls the state of the output stage. Transistor Q2 in the output stage is on with the LED off, allowing the base of the power device to be held low. Turning on the LED turns off transistor Q2 and switches on transistor Q1 in the output stage which provides current to drive the base of a power bipolar device.
• High output current IO2 A Peak, A continuous IO1 A Peak, A continuous
• 10 kV/µs minimum Common Mode Rejection CMR at VCM = 600 V
• Wide VCC range to 13 volts
• 2 µs typical propagation delay
• Recognized under UL 1577 for dielectric withstand proof
test voltage of 5000 vac, 1 minute
• Isolated bipolar transistor base drive
• AC and DC motor drives
• General purpose industrial inverters
• Uninterruptable power supply

Functional Diagram

ANODE 1 CATHODE 2

HCPL-3000
8 VCC
7 GND Q2
6 VO2 Q1
5 VO1

TRUTH TABLE

LED OUTPUT

Q1 Q2

ON HIGH LEVEL ON OFF

OFF LOW LEVEL OFF ON

THE USE OF A 0.1µF BYPASS CAPACITOR CONNECTED BETWEEN PINS 8 AND 7 IS RECOMMENDED. ALSO, CURRENT LIMITING RESISTORS ARE RECOMMENDED SEE FIGURE 1, NOTE 2, AND NOTE

CAUTION It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

Schematic
1 ANODE

CATHODE

Q1 I O2 6 VO2
Ordering Information

HCPL-3000 is UL Recognized with 5000 Vrms for 1 minute per UL1577.

HCPL-3000

Option

RoHS Compliant -000E -300E -500E

Package 300 mil DIP-8

Surface Mount

Gull Wing

Tape & Reel

Quantity 50 per tube 50 per tube 1000 per reel

To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry.

Example 1 HCPL-3000-500E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging and RoHS compliant.

Example 2 HCPL-3000-000E to order product of 300 mil DIP package in Tube packaging and RoHS compliant.

Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.

Remarks The notation ‘#XXX’ is used for existing products, while new products launched since July 15, 2001 and RoHS compliant will use

Outline Drawing

TYPE NUMBER

DATE CODE

A XXXX YYWW
0° 13°
0° 13°

ANODE 1 CATHODE 2

HCPL-3000
8 VCC
7 GND Q2
6 VO2 Q1
5 VO1

Regulatory Information

The HCPL-3000 has been approved by the following organizations:

Recognized under UL 1577, Component Recognition Program, File E55361.

Demonstrated ESD Performance

Human Body Model MIL-STD883 Method Class 2

Machine Model EIAJ IC-121 1988 Version 2 , Test Method 20, Condition C 1200 V

Insulation and Safety Related Specifications

Parameter

Min. External Air Gap External Clearance

Min. External Tracking Path External Creepage

Min. Internal Plastic Gap Internal Clearance

Symbol Value Units L IO1 mm L IO2 mm

Conditions

Shortest distance measured through air, between two conductive leads, input to output

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HCPL-3000 Datasheet file may be downloaded here without warranties.

Datasheet ID: HCPL-3000 520249