ACPM-7813-BLK

ACPM-7813-BLK Datasheet

ACPM-7813 CDMA/AMPS Power Amplifier Module

Part	Datasheet
ACPM-7813-BLK	ACPM-7813-BLK (pdf)

Related Parts	Information
ACPM-7813-TR1	ACPM-7813-TR1

PDF Datasheet Preview
ACPM-7813 CDMA/AMPS Power Amplifier Module Data Sheet The ACPM-7813 is a fully matched CDMA Power amplifier module. Designed around Avago Technologies’ new Enhancement Mode pHEMT process, the ACPM-7813 offers premium performance in a very small form factor. Fully matched to 50 Ohms on the input and output. The amplifier has excellent ACPR and efficiency performance at max Pout and low quiescent current with a single bias control voltage. For even lower quiescent current, a dynamic bias control circuit can be used by varying the voltage on the Vcntl pin between 1.2V to 2.5V. Designed in a surface mount RF package, the ACPM7813 is cost and size competitive. The ACPM-7813 is another key component of the Avago Technologies CDMAdvantage RF chipset. • Operating frequency 849 MHz • dBm linear output power 3.4V • High efficiency 40% PAE • Dynamic bias control for low midpower Idd • Very low quiescent current with single control voltage • Internal 50 ohm matching networks for both RF IN/ OUT • 4.2V linear operation • cdma2000 1xRTT capable • Only 3 SMT parts needed • x mm SMT package • CDMA handsets • Datacards • PDAs Vdd1 Vbias Vdd2 Input Power Input Match Bias Circuit On Chip Inter-stage Match Passive Output Match Output Vcntl Single control bias setting for low Idq and 40%PAE at Pout = dBm Maximum Ratings[1] Parameter Min. Max. Vdd Supply Voltage Power Dissipation [2] Bias Current Control Voltage Vcntl Amplifier Input RF Power 10 dBm Junction Temperature +150°C Storage Temperature case temperature -40°C +100°C Notes Operation of this device in excess of any of these limits may cause permanent damage. Tcase = 25°C Thermal Resistance[2] = 22.3°C/W Recommended operating range of Vdd = to V, Ta = -30 to +85°C Package Marking and Dimensions Agilent ACPM-7813 Ordering Information Part Number ACPM-7813-BLK ACPM-7813-TR1 No. of Devices 10 1000 Tape Dimensions and Orientation ± ± Notes Measured from centerline of sprocket hole to centerline of pocket Cumulative tolerance of 10 sprocket holes is mm All dimensions in millimeters unless otherwise stated. Container Bulk 7” Tape and Reel ± ± Agilent ACPM-7813 YYWWDD XXXX Reel Drawing BACK VIEW Shading indicates thru slots max. 25 min wide ref Slot for carrier tape insertion for attachment to reel hub 2 places 180 apart FRONT VIEW 50 min. min. NOTES Reel shall be labeled with the following information as a minimum . a. manufacturers name or symbol b. Avago Technologies part number c. purchase order number d. date code e. quantity of units A certificate of compliance c of c shall be issued and accompany each shipment of product. Reel must not be made with or contain ozone depleting materials. All dimensions in millimeters mm Application Information The following material is presented to assist in general design and use of the APCM-7813. • 3.0V Characterization, for use in Data Card Applications • cdma2000 1XRTT Description and Characterization data • Design tips on various methods to control the bias on Vcntl pin • Description of ACPR measurement methods • Description of Avago Technologies evaluation demoboard for ACPM-7813 • IR Reflow Profile applicable for all Avago Technologies E-pHEMT PAs 3.0V Characterization, Data Card Applications Electrical Data All tests are done in system at Vdd1=Vdd2=Vbias = 3.0V, 25°C, unless noted otherwise. Parameter Units Min Typ 800 MHz CDMA Frequency Range Gain Fixed Cntl Voltage Pout = dBm Pout = 13 dBm Pout = -5 dBm Power Added Efficiency Pout = dBm Pout = 16 dBm Total Supply Current ACPR ± MHz offset dBc/30 kHz ACPR ± MHz offset dBc/30 kHz Quiescent Current Input VSWR Pout = dBm Pout = 16 dBm Noise Figure Noise Power 45 MHz offset in 869 894 MHz

PDF Datasheet Preview

ACPM-7813 CDMA/AMPS Power Amplifier Module

Data Sheet

The ACPM-7813 is a fully matched CDMA Power amplifier module. Designed around Avago Technologies’ new Enhancement Mode pHEMT process, the ACPM-7813 offers premium performance in a very small form factor. Fully matched to 50 Ohms on the input and output.

The amplifier has excellent ACPR and efficiency performance at max Pout and low quiescent current with a single bias control voltage. For even lower quiescent current, a dynamic bias control circuit can be used by varying the voltage on the Vcntl pin between 1.2V to 2.5V.

Designed in a surface mount RF package, the ACPM7813 is cost and size competitive.

The ACPM-7813 is another key component of the Avago Technologies CDMAdvantage RF chipset.
• Operating frequency 849 MHz
• dBm linear output power 3.4V
• High efficiency 40% PAE
• Dynamic bias control for low midpower Idd
• Very low quiescent current with single control
voltage
• Internal 50 ohm matching networks for both RF IN/

OUT
• 4.2V linear operation
• cdma2000 1xRTT capable
• Only 3 SMT parts needed
• x mm SMT package
• CDMA handsets
• Datacards
• PDAs

Vdd1

Vbias

Vdd2

Input

Power Input Match

Bias Circuit

On Chip Inter-stage

Match

Passive Output Match

Output

Vcntl

Single control bias setting for low Idq and 40%PAE at Pout = dBm

Maximum Ratings[1]

Parameter

Min.

Max.

Vdd Supply Voltage Power Dissipation [2]

Bias Current

Control Voltage Vcntl

Amplifier Input RF Power
10 dBm

Junction Temperature
+150°C

Storage Temperature case temperature
-40°C
+100°C

Notes Operation of this device in excess of any of these limits may cause permanent damage. Tcase = 25°C

Thermal Resistance[2] = 22.3°C/W

Recommended operating range of Vdd = to V, Ta = -30 to +85°C

Package Marking and Dimensions

Agilent ACPM-7813
Ordering Information

Part Number ACPM-7813-BLK ACPM-7813-TR1

No. of Devices 10 1000

Tape Dimensions and Orientation
± ±

Notes Measured from centerline of sprocket hole to centerline of pocket Cumulative tolerance of 10 sprocket holes is mm All dimensions in millimeters unless otherwise stated.

Container Bulk 7” Tape and Reel
± ±

Agilent ACPM-7813

YYWWDD XXXX

Reel Drawing

BACK VIEW

Shading indicates thru slots
max.
25 min wide ref Slot for carrier tape insertion for attachment to reel hub 2 places 180 apart

FRONT VIEW
50 min.
min.

NOTES Reel shall be labeled with the following
information as a minimum . a. manufacturers name or symbol b. Avago Technologies part number c. purchase order number d. date code e. quantity of units A certificate of compliance c of c shall be issued and accompany each shipment of product. Reel must not be made with or contain ozone depleting materials. All dimensions in millimeters mm

Application Information

The following material is presented to assist in general design and use of the APCM-7813.
• 3.0V Characterization, for use in Data Card Applications
• cdma2000 1XRTT Description and Characterization data
• Design tips on various methods to control the bias on Vcntl pin
• Description of ACPR measurement methods
• Description of Avago Technologies evaluation demoboard for ACPM-7813
• IR Reflow Profile applicable for all Avago Technologies E-pHEMT PAs
3.0V Characterization, Data Card Applications

Electrical Data

All tests are done in system at Vdd1=Vdd2=Vbias = 3.0V, 25°C, unless noted otherwise.

Parameter

Units

Min Typ
800 MHz CDMA

Frequency Range

Gain Fixed Cntl Voltage Pout = dBm Pout = 13 dBm Pout = -5 dBm

Power Added Efficiency Pout = dBm Pout = 16 dBm

Total Supply Current

ACPR ± MHz offset
dBc/30 kHz

ACPR ± MHz offset
dBc/30 kHz

Quiescent Current

Input VSWR Pout = dBm Pout = 16 dBm

Noise Figure

Noise Power 45 MHz offset in 869 894 MHz

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ACPM-7813-BLK Datasheet file may be downloaded here without warranties.

Datasheet ID: ACPM-7813-BLK 519897