3435S-1-502

3435S-1-502 Datasheet

Model 3435 is currently available, although not recommended for new designs. Model 6657 is preferred.

Part	Datasheet
3435S-1-502	3435S-1-502 (pdf)

PDF Datasheet Preview
• 27 mm 1-1/16 diameter, single-turn wirewound • Bushing mount • Gangable to 8 cups • Outstanding vibration and shock performance • Shaft supported front and rear by precision sleeve bearings Model 3435 is currently available, although not recommended for new designs. Model 6657 is preferred. • High temperature, moisture resistant, thermosetting plastic housing • Non-standard features and specifications available 3435 - Precision Potentiometer Electrical Characteristics1 Standard Resistance Range to 20 K ohms Total Resistance Tolerance % Independent Linearity % Effective Electrical Angle ° ±2 ° ohms ENR maximum Absolute Minimum Resistance ohm or % whichever is greater Dielectric Withstanding Voltage Sea Level VAC minimum Power Rating +70 watts +125 watt Insulation Resistance 500 megohms minimum Resolution ordering information Environmental Characteristics1 Operating Temperature °C to 125 °C Storage Temperature °C to +125 °C Temperature Coefficient Over Storage Temperature ppm/°C max. Vibration MIL-R-12934 G Mechanical Characteristics1 Mechanical Angle Torque Starting N-cm oz.-in. maximum Running N-cm oz.-in. maximum Additional 75 % each N-cm 15-18 lb.-in. maximum Shaft mm in. T.I.R. Shaft End Play mm in. T.I.R. Shaft Radial Play mm in. T.I.R. Backlash ° maximum 23 gm Terminals turret type Soldering Condition Manual solid wire or no-clean rosin cored wire 370 °C 700 °F max. for 3 seconds Wave Soldering solder with no-clean flux 260 °C 500 °F max. for 5 seconds Wash processes recommended Marking name and part number, resistance value and tolerance, linearity tolerance, wiring diagram, date code Ganging Multiple Section Potentiometers cups maximum Hardware lockwasher H-37-2 and one mounting nut H-38-2 is shipped with each potentiometer. 1At room ambient +25 nominal and 50 % relative humidity nominal, except as noted. 2Consult factory for complete specification details. Product Dimensions 3435 ± ± MIN. ± ± 3/8 " - 32 UNEF 2A 30 ° 30 ° ±5° ±5° CCW CW NOTE LOCKWASHER AND HEX NUT TO BE SUPPLIED WITH EACH UNIT. R MAX. SHAFT X ± SLOT TOLERANCES EXCEPT WHERE NOTED DECIMALS .XX .XXX FRACTIONS ±1/64 DIMENSIONS: MM IN. 2 WIPER CCW 1 CLOCKWISE Recommended Part Numbers 3435S-1-102 3435S-1-202 3435S-1-502 3435S-1-103 3435S-1-503 Resistance Resolution 1,000 2,000 5,000 10,000

PDF Datasheet Preview

• 27 mm 1-1/16 diameter, single-turn wirewound
• Bushing mount
• Gangable to 8 cups
• Outstanding vibration and shock performance
• Shaft supported front and rear by precision sleeve bearings

Model 3435 is currently available, although not recommended for new designs. Model 6657 is preferred.
• High temperature, moisture resistant, thermosetting plastic housing
• Non-standard features and specifications available
3435 - Precision Potentiometer

Electrical Characteristics1

Standard Resistance Range to 20 K ohms Total Resistance Tolerance % Independent Linearity % Effective Electrical Angle ° ±2 ° ohms ENR maximum Absolute Minimum Resistance ohm or % whichever is greater Dielectric Withstanding Voltage

Sea Level VAC minimum Power Rating
+70 watts +125 watt Insulation Resistance 500 megohms minimum Resolution ordering information

Environmental Characteristics1

Operating Temperature °C to 125 °C Storage Temperature °C to +125 °C Temperature Coefficient Over Storage Temperature ppm/°C max. Vibration MIL-R-12934 G

Mechanical Characteristics1

Mechanical Angle Torque

Starting N-cm oz.-in. maximum Running N-cm oz.-in. maximum Additional 75 % each N-cm 15-18 lb.-in. maximum Shaft mm in. T.I.R. Shaft End Play mm in. T.I.R. Shaft Radial Play mm in. T.I.R. Backlash ° maximum 23 gm Terminals turret type Soldering Condition Manual solid wire or no-clean rosin cored wire
370 °C 700 °F max. for 3 seconds Wave Soldering solder with no-clean flux
260 °C 500 °F max. for 5 seconds Wash processes recommended Marking name and part number, resistance value and tolerance,
linearity tolerance, wiring diagram, date code Ganging Multiple Section Potentiometers cups maximum Hardware lockwasher H-37-2 and one mounting nut H-38-2
is shipped with each potentiometer.
1At room ambient +25 nominal and 50 % relative humidity nominal, except as noted. 2Consult factory for complete specification details.

Product Dimensions
3435 ± ±

MIN.
± ±
3/8 " - 32 UNEF 2A
30 °
30 °
±5°
±5°

CCW CW

NOTE LOCKWASHER AND HEX NUT TO BE SUPPLIED WITH EACH UNIT.

R MAX.

SHAFT X ±

SLOT

TOLERANCES EXCEPT WHERE NOTED

DECIMALS .XX
.XXX

FRACTIONS ±1/64

DIMENSIONS:

MM IN.
2 WIPER

CCW 1

CLOCKWISE

Recommended Part Numbers
3435S-1-102 3435S-1-202 3435S-1-502 3435S-1-103 3435S-1-503

Resistance Resolution
1,000
2,000
5,000
10,000

More datasheets: 78-6972-0005-9 | 78-6972-0006-7 | 78-6972-0007-5 | 78-6972-0004-2 | 78-6969-9997-4 | 78-6972-0002-6 | 78-6972-0001-8 | 78-6972-0003-4 | FQB85N06TM_AM002 | SJ3526N

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 3435S-1-502 Datasheet file may be downloaded here without warranties.

Datasheet ID: 3435S-1-502 522056