1887215

1887215 Datasheet

Part	Datasheet
1887215	1887215 (pdf)

Related Parts	Information
1887214	1887214
1886887	1886887
1886886	1886886

PDF Datasheet Preview
Technical Data Sheet LOCTITE TCF 4000 PXF April-2014 PRODUCT DESCRIPTION LOCTITE TCF 4000 PXF provides the following product characteristics: Technology Phase Change Appearance Gray Application Method Manual application Product Benefits ● Low thermal resistance ● Non silicone ● No pump-out, dry-out or pull-out Phase change temperature 45 °C Application Thermal management Typical Assembly Thermal grease replacement in computing applications, Lidded and bare die processor applications and Used between any heat generating electrically isolated component and a heat sink LOCTITE TCF 4000 PXF is a reworkable phase change thermal interface material suitable for use between a heat sink and variety heat dissipating components. The material flows at the phase change temperature, conforming to the surface features of the components. Upon flow, air is expelled from the interface, reducing thermal impedance, performing as a highly efficient thermal transfer material. Custom parts are also available upon request with low cost tooling. TYPICAL PROPERTIES PXF-8 with Volumetric Expansion on phase change, % Thermal Impedance , ASTM D5470: 20 psi, ºC-in2/W 80 psi, ºC-in2/W Compound Thickness Before Phase Change Inches mm Viscosity Above Phase Change Temp PXF-16 Volumetric Expansion on phase change, % Thermal Impedance , ASTM D5470 20 psi, ºC-in2/W 80 psi, ºC-in2/W Compound Thickness Before Phase Change Inches mm Viscosity Above Phase Change Temp thixotropic thixotropic THERMAL RESISTANCE vs. MOUNTING PRESSURE GENERAL INFORMATION For safe handling information on this product, consult the Material Safety Data Sheet, MSDS . DIRECTIONS FOR USE This product is packaged as a free-standing film between two release liners and is supplied as a die cut preform to match a wide variety of applications. Currently supplied in two compound thicknesses, multiple thicknesses will soon be available to match surface finishes and flatness considerations in the interface area. LOCTITE TCF 4000 PXF is completely reworkable without solvents and is easier to remove than previous formulations. If a clean surface is required, any compound present can easily be removed with mineral spirits. No silicones are utilized in the formulation of the phase change compound. Unlike previous versions of Powerstrate, LOCTITE TCF 4000 PXF does not require adhesive edge strips for heatsink attach applications. The "tacky" nature of the product allows for it to naturally adhere to the heatsink surface. Storage Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.

PDF Datasheet Preview

Technical Data Sheet

LOCTITE TCF 4000 PXF

April-2014

PRODUCT DESCRIPTION

LOCTITE TCF 4000 PXF provides the following product
characteristics:

Technology

Phase Change

Appearance

Gray

Application Method

Manual application

Product Benefits
● Low thermal resistance
● Non silicone
● No pump-out, dry-out or pull-out

Phase change temperature 45 °C

Application

Thermal management

Typical Assembly

Thermal grease replacement in
computing applications, Lidded and
bare die processor applications and

Used between any heat generating
electrically isolated component and a
heat sink

LOCTITE TCF 4000 PXF is a reworkable phase change thermal interface material suitable for use between a heat sink and variety heat dissipating components. The material flows at the phase change temperature, conforming to the surface features of the components. Upon flow, air is expelled from the interface, reducing thermal impedance, performing as a highly efficient thermal transfer material. Custom parts are also available upon request with low cost tooling.

TYPICAL PROPERTIES PXF-8 with

Volumetric Expansion on phase change, % Thermal Impedance , ASTM D5470:
20 psi, ºC-in2/W 80 psi, ºC-in2/W Compound Thickness Before Phase Change Inches mm Viscosity Above Phase Change Temp

PXF-16 Volumetric Expansion on phase change, % Thermal Impedance , ASTM D5470 20 psi, ºC-in2/W 80 psi, ºC-in2/W Compound Thickness Before Phase Change Inches mm Viscosity Above Phase Change Temp
thixotropic
thixotropic

THERMAL RESISTANCE vs. MOUNTING PRESSURE

GENERAL INFORMATION For safe handling information on this product, consult the Material Safety Data Sheet, MSDS . DIRECTIONS FOR USE

This product is packaged as a free-standing film between two release liners and is supplied as a die cut preform to match a wide variety of applications.

Currently supplied in two compound thicknesses, multiple thicknesses will soon be available to match surface finishes and flatness considerations in the interface area.

LOCTITE TCF 4000 PXF is completely reworkable without solvents and is easier to remove than previous formulations.

If a clean surface is required, any compound present can easily be removed with mineral spirits. No silicones are utilized in the formulation of the phase change compound.

Unlike previous versions of Powerstrate, LOCTITE TCF 4000 PXF does not require adhesive edge strips for heatsink attach applications. The "tacky" nature of the product allows for it to naturally adhere to the heatsink surface.

Storage Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 1887215 Datasheet file may be downloaded here without warranties.

Datasheet ID: 1887215 646588