232MDS3

232MDS3 Datasheet

232MDS3 0812-1/1

Part	Datasheet
232MDS3	232MDS3 (pdf)

PDF Datasheet Preview
B&B ELECTRONICS 232MDS3 0812-1/1 2002 by B&B Electronics. All rights reserved. Model 232MDS3 Modem Data Splitter Overview DECLARATION OF CONFORMITY The Modem Data Splitter can be connected so that three computers or terminals can use one modem without manual switching. The Modem Data Splitter can be used to combine three DTE ports to a DCE port. Manufacturer’s Name Manufacturer’s Address: B&B Electronics Manufacturing Company P.O. Box 1040 707 Dayton Road Ottawa, IL 61350 USA 232MDS3 All signals entering the female DTE connectors on pin 2 Transmit Data , 4 Request To Send , and 20 Data Terminal Ready are diode OR'd together and appear as Description Type Application of Council Directive Standards: Modem Data Splitter Light industrial ITE equipment 89/336/EEC EN 50082-1 outputs on the male DCE connector. Pins 3 Receive Data , 5 EN 61000 -4-2, -4-3, -4-4, -4-5, -4-6, -4-8, -4-11 Clear To Send , 6 Data Set Ready , and 8 Carrier Detect are normally outputs from a DCE port, so they are connected directly from the male to all female connectors. Can be left permanently installed. To ensure proper operation, lines 2, 4, and 20 on the Robert M. Paratore, Director of Engineering unused female inputs should be low or open to allow the other inputs to operate properly. Pins 1 and 7 are connected to provide a ground path. Pin 1 is Protective Ground and Pin 7 is Signal Ground on all three DB25 connectors. To install the 232MDS3, connect a "straight through" cable Pin 1 to Pin 1, Pin 2 to Pin 2, etc. between the terminals. PRODUCT INFORMATION International Office 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 European Office Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445

PDF Datasheet Preview

B&B ELECTRONICS
232MDS3 0812-1/1
2002 by B&B Electronics. All rights reserved.

Model 232MDS3

Modem Data Splitter

Overview

DECLARATION OF CONFORMITY

The Modem Data Splitter can be connected so that three computers or terminals can use one modem without manual switching. The Modem Data Splitter can be used to combine three DTE ports to a DCE port.

Manufacturer’s Name Manufacturer’s Address:

B&B Electronics Manufacturing Company P.O. Box 1040 707 Dayton Road Ottawa, IL 61350 USA 232MDS3

All signals entering the female DTE connectors on pin 2 Transmit Data , 4 Request To Send , and 20 Data Terminal Ready are diode OR'd together and appear as

Description Type Application of Council Directive Standards:

Modem Data Splitter Light industrial ITE equipment 89/336/EEC EN 50082-1
outputs on the male DCE connector. Pins 3 Receive Data , 5

EN 61000 -4-2, -4-3, -4-4, -4-5, -4-6, -4-8, -4-11

Clear To Send , 6 Data Set Ready , and 8 Carrier Detect
are normally outputs from a DCE port, so they are connected
directly from the male to all female connectors. Can be left
permanently installed. To ensure proper operation, lines 2, 4, and 20 on the Robert M. Paratore, Director of Engineering
unused female inputs should be low or open to allow the other inputs to operate properly. Pins 1 and 7 are connected
to provide a ground path. Pin 1 is Protective Ground and Pin 7 is Signal Ground on all three DB25 connectors.

To install the 232MDS3, connect a "straight through" cable Pin 1 to Pin 1, Pin 2 to Pin 2, etc. between the
terminals.

PRODUCT INFORMATION

International Office 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 European Office Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 232MDS3 Datasheet file may be downloaded here without warranties.

Datasheet ID: 232MDS3 521476