SG2-PM05

SG2-PM05 Datasheet


SG2 PLR USER Manual

Part Datasheet
SG2-PM05 SG2-PM05 SG2-PM05 (pdf)
PDF Datasheet Preview
SG2 PLR USER Manual

SG2 Programmable Logic Relay
1-800-972-0436

Table of Contents

Chapter 1 Getting Started

Examination Before Installation Environmental Precautions SG2 Model Identification

Quick Start Setup Chapter 2 Installation

General Specifications Product Specifications Mounting Wiring

Chapter 3 Program Tools

PC Programming Software “SG2 Client” Memory Cartridge LCD Display and Keypad

Chapter 4 Relay Ladder Logic Programming

Specialty Memory Types Output Instructions Counter Instructions High Speed Counters DC Version PLRs Only Timer Instructions Real Time Clock RTC Instructions Comparator Instructions HMI Display Instructions PWM Output Instruction DC Transistor Output Models Only Data Link/Remote I/O Instruction SG2-20Vxx Models Only

User Manual

Chapter 5 Function Block Diagram Programming

Coil Block Instruction Logic Block Instructions PWM Function Block SHIFT Function Block AND Logic Block AND Edge Logic Block NAND Logic Block NAND Edge Logic Block OR Logic NOR Logic XOR Logic SR Logic Block NOT Logic Block Pulse Logic Block Counter Function Block Counter Mode 5 Counter Mode 6 High Speed Counter Function Block Timer Function Block RTC Function Block Analog comparator Function Block

SG2 PLR User Manual
4 Chapter 1 Getting Started

Chapter 1 Getting Started

The SG2 PLR is an electronic device. For safety reasons, please carefully read and follow the paragraphs with "WARNING" or "CAUTION" symbols.They are important safety precautions to be aware of while transporting, installing, operating, or examining the SG2 Controller.

WARNING Personal injury may result from improper operation.

CAUTION The SG2 PLR may be damaged by improper operation.

Precaution for Installation

Compliance with the installation instructions and the user manual is absolutely necessary. Failure to comply could lead to improper operation, equipment damage or in extreme cases even death, serious bodily injury or considerable damage to property. When installing the open-board models, insure that no wiring or foreign materials can fall into the exposed circuits and components. Damage to equipment, fire, or considerable damage to property could result.

Always switch off power before you wire, connect, install, or remove any module. The wiring for the SG2 PLR is open and exposed. For the open-board models, all electrical components are exposed. For this reason, it is recommended the SG2 PLR be installed in an enclosure or cabinet to prevent accidental contact or exposure to the electrical circuits and components. Never install the product in an environment beyond the limits specified in this user manual such as high temperature, humidity, dust, corrosive gas, vibration, etc.

Precaution for Wiring

Improper wiring and installation could lead to death, serious bodily injury or considerable damage to property.

The SG2 PLR should only be installed and wired by properly experienced and certified personnel. Make sure the wiring of the SG2 PLR meets all applicable regulations and codes including local and national standards and codes.

Be sure to properly size cables for the required current rating.

Always separate AC wiring, DC wiring with high-frequency switching cycles, and low-voltage signal wiring.

Precaution for Operation

To insure safety with the application of the SG2 PLR, complete functional and safety testing must be conducted. Only run the SG2 after all testing and confirming safe and proper operation is complete. Any potential faults in the application should be included in the testing. Failure to do so could lead to improper operation, equipment damage or in extreme cases even Death, serious bodily injury or considerable damage to property. When the power is on, never contact the terminals, exposed conductors or electrical components. Failure to comply could lead to improper operation, equipment damage or in extreme cases even death, serious bodily injury or considerable damage to property. It is strongly recommended to add safety protection such as an emergency stop and external interlock circuit in case the SG2 PLR operation must be shut down immediately.

User Manual

Chapter 1 Getting Started 5

Examination Before Installation

Every SG2 PLR has been fully tested and examined before shipment. Please carry out the following examination procedures after unpacking your SG2 Programmable Logic Relay.
• Check to see if the model number of the SG2 matches the model number that you ordered.
• Check to see whether any damage occurred to the SG2 during shipment. Do not connect the SG2 PLR to the power
supply if there is any sign of damage. Contact FactoryMation if you find any abnormal conditions as mentioned above.

Environmental Precautions

The installation site of the SG2 PLR is very important. It relates directly to the functionality and the life span of your SG2 Please carefully choose an installation site that meets the following requirements:
• Mount the unit vertically
• Environment temperature 32°F - 131°F 0°C - 55°C
• Avoid placing SG2 close to any heating equipment
• Avoid dripping water, condensation, or humid environment
• Avoid direct sunlight
• Avoid oil, grease, and gas
• Avoid contact with corrosive gases and liquids
• Prevent foreign dust, flecks, or metal scraps from contacting the SG2 PLR
• Avoid electric-magnetic interference soldering or power machinery
• Avoid excessive vibration if vibration cannot be avoided, an anti-rattle mounting device should be installed to reduce
vibration.
More datasheets: HLMP-RD11-LPTDD | HLMP-RL10-LP0DD | HLMP-SL10-LP0DD | HLMP-SD11-LP000 | HLMP-SL11-LP0DD | HLMP-SD11-MNTDD | HLMP-SD11-J0000 | HLMP-RL10-LP000 | HLMP-RB11-H00DD | SF25-0881M5UB02


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived SG2-PM05 Datasheet file may be downloaded here without warranties.

Datasheet ID: SG2-PM05 521462