70-841-015
70-841-015 Datasheet
Astec connector kit #70-841-015, includes al of the above.
| Part | Datasheet |
|---|---|
70-841-015 |
70-841-015 (pdf) |
| PDF Datasheet Preview |
|---|
| 175 Watts LPQ172 Series Total Power 110-175 Watts Input Voltage 85-264 VAC 120-300 VDC # of Outputs Quad Electrical Specs Input Input range Frequency Inrush current Efficiency EMI filter Power factor Safety ground leakage current 85-264 VAC, 120-300 VDC 47-63 Hz 38 A max, cold start 25°C 75% typical at full load Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted typical mA 50/60 Hz, 264 VAC input Special Features • Active power factor correction • IEC EN61000-3-2 compliance • Adjustable outputs on 1, 3 & 4 Remote sense on main output • Single wire current sharing • Power fail and remote inhibit • Built-in EMI filter • Low output ripple • Overvoltage protection • Overload protection • Thermal overload protection • DC power good • 5 V standby output • Adjustable floating 4th output • Optional cover -C suffix Environmental Operating temperature 0° to 50°C ambient derate each output at per degree from 50° to 70°C except for -C version Electromagnetic susceptibility designed to meet EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 Humidity Operating non-condensing 5% to 95% Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances G peak 5 Hz to 500 Hz, operational Storage temperature -40° to 85°C Temperature coefficient ± per °C MTBF demonstrated >550,000 hours at full load and 25°C ambient conditions Output Maximum power Adjustment range Hold-up time Overload protection Overvoltage protection Standby output Logic Control AC Power failure Remote inhibit Remote sense DC Ok 110 W convection 75 W with cover 175 W with 30 CFM forced air 130 W with cover - 5.5V on main -12 - 15V on 3rd output - 25 V on 4th output 20 ms W load at nominal line Short circuit protection on all outputs. Case overload protected 110-145% above peak rating Tracks outputs 1, 3 & 4 15 to 35% 5 V 200 mA regulated ±5% VDE UL CB CSA CE NEMKO Safety 0805/EN60950 IEC950 UL1950 Certificate and report CSA Level 3 Mark LVD EN 60950/EMKO-TUE Americas 1-888-41-ASTEC Europe UK 44 1384 842-211 Asia HK 852-2437-9662 AMERICAS Ordering Information Model Number LPQ172 Output Voltage Minimum Load 5 V - V 12 V -12 V -12 -15 V 0A A* Maximum Load with Convection Cooling 15 A 6A A 2A Maximum Load with 30 CFM Forced Air 30 A 8A 3A 5A Peak Load 32 A 10 A Regulation2 ±2% ±3% ±3% ±3% Ripple P/P PARD 3 50 mV 120 mV <1% <50mV or 1% Peak current lasting <30 seconds with a maximum 10% duty cycle. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a µF capacitor at rated line voltage and load ranges. 4th output adjustable V factory set at 5 V. *Minimum loads are required when output set below 5 Volts Remote inhibit resets OVP latch Note -C suffix added to the model number indicates cover option and is limited to 50C operation. Pin Assignments Connector LPQ172 PIN 1 PIN 2 5V Standby PIN 3 PIN 4 V1 SWP PIN 5 Common PIN 6 +V1 sense PIN 7 Sense common PIN 8 Remote inhibit PIN 9 DC power good PIN 10 PIN 1,2 +12 V PIN 3,4,5 Common PIN 6 |
| More datasheets: CWR-181-15-0021 | CWR-182-25-0021 | CWR-182-37-0000 | CWR-183-37-0000 | CWR-182-09-0021 | CWR-180-09-0021 | CWR-181-09-0021 | CWR-183-09-0021 | CWR-182-15-0003 | CWR-183-09-0000 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 70-841-015 Datasheet file may be downloaded here without warranties.