PTH03060YAZT

PTH03060YAZT Datasheet


PTHxx060Y Vin

Part Datasheet
PTH03060YAZT PTH03060YAZT PTH03060YAZT (pdf)
Related Parts Information
PTH12060YAD PTH12060YAD PTH12060YAD
PTH05060YAD PTH05060YAD PTH05060YAD
PTH12060YAZT PTH12060YAZT PTH12060YAZT
PTH12060YAZ PTH12060YAZ PTH12060YAZ
PTH12060YAST PTH12060YAST PTH12060YAST
PTH03060YAD PTH03060YAD PTH03060YAD
PTH03060YAZ PTH03060YAZ PTH03060YAZ
PTH12060YAS PTH12060YAS PTH12060YAS
PTH05060YAZT PTH05060YAZT PTH05060YAZT
PTH05060YAZ PTH05060YAZ PTH05060YAZ
PDF Datasheet Preview
PTHxx060Y Vin

Total Power 18 Watts # of Outputs Single

Embedded Power for Business-Critical Continuity

Special Features
• VTT bus termination output the system VREF
• 10 A output current
• 5 or 12 Vdc input
voltage
• DDR and QDR compatible
• ON/OFF inhibit for VTT
standby
• Under-voltage lockout
• Operating temperature
range -40 °C to +85 °C
• Efficiencies up to 91%
• Output overcurrent
protection non-latching, auto-reset
• Point-of-Load-Alliance POLA compatible
• Available RoHS compliant
• 2 Year Warranty

Safety
• UL/cUL CAN/CSA-C22.2 No. 60950, File No. E174104
• TÜV Product Service EN60950 Certificate No. B 04 06 38572 044 CB Report and Certificate to IEC60950, Certificate No. US/8292/UL

Specifications

Input current Input voltage range:

Undervoltage lockout PTH03060Y

PTH05060Y

PTH12060Y

Input capacitance See Note 3, page 3 Remote ON/OFF:

No load

PTH03060Y PTH05060Y PTH12060Y
10 mA
- Vdc - Vdc - Vdc

Vin increasing Vin decreasing

Vin increasing Vin decreasing

Vin increasing Vin decreasing

PTH03060Y & PTH05060Y PTH12060Y

V typ., V max. V min., V typ.

V typ., V max. V min., V typ.

V typ., V max. V min., V typ.
330 µF
560 µF

Positive logic

All specifications are typical at nominal input, Vref = V, full load at unless otherwise stated. Cin, Co1 and Co2 = typical value

Embedded Power for Business-Critical Continuity

Specifications Continued

Output current See Note 1, page 3 Tracking range for VREF Tracking tolerance to VREF VTT - VREF over line, load & temperature

Ripple and noise Load transient response See Note 4, page 3 Output capacitance Non-ceramic values See Notes 4 & 5, page 3

Ceramic values See Note 4, page 3

See Note 6, page 3
over range
Ordering Information

Output Power max

Input Voltage
18 W 18 W 18 W
- Vdc - Vdc
- Vdc

VTT Range - Vdc - Vdc - Vdc

Output Currents
±10 A
±10 A
±10 A

Part Number System with Options PTH05060YAST

Product Family Point of Load Alliance

Compatible

Efficiency max
86% 86% 83%

PTH03060Y PTH05060Y PTH12060Y

Packaging Options No Suffix = Trays T = Tape and Reel 7

Input Voltage 03 = V, 05 = 5 V
and 12 = 12 V

Output Current 06 = 10 A

Mechanical Package Always 0

Mounting Option 8 D = Horizontal Through-Hole RoHS 6/6 H = Horizontal Through-Hole RoHS 5/6 S = Surface-Mount Solder Ball RoHS 5/6 Z = Surface-Mount Solder Ball RoHS 6/6

Pin Option A = Through-Hole Std. Pin Length A = Surface-Mount Tin/Lead Solder Ball

Output Voltage Code Y = DDR Module

Notes 1 Rating is conditional on the module being soldered to a 4 layer PCB
with 1 oz. copper. See the SOA curves or contact the factory for appropriate derating. 2 This control pin has an internal pull-up to the input voltage Vin. If it is left open-circuit the module will operate when input power is applied. A small low-leakage <100 nA MOSFET is recommended for control. For further information, consult Application Note 3 An input capacitor is required for proper operation. The capacitor must be rated for a minimum of 500 mA rms 1000 mA for 12 V input of ripple current. For further information, consult Application Note 179 on capacitor selection. 4 The typical value of external output capacitance value ensures that afoyr be possible when the measured peak change in output current is consistently less than 3 A. Test conditions were 15 A/µs load step, A to A.
5 This is the calculated maximum. The minimum ESR limitation will often result in a lower value. Consult Application Note 179 for further details.
6 This is the typical ESR for all the electrolytic non-ceramic output capacitance. Use 7 mΩ as the minimum when using max-ESR values to calculate.
7 Tape and reel packaging only available on the surface-mount versions.
8 To order Pb-free RoHS compatible surface-mount parts replace the mounting option ‘S’ with ‘Z’, e.g. PTHXX060YAZ. To order Pbfree RoHS compatible through-hole parts replace the mounting option ‘H’ with ‘D’, e.g. PTHXX060YAD.
9 NOTICE Some models do not support all options. Please contact your local Emerson Network Power representative or use the on-line model number search tool at to find a suitable alternative.

PTHxx060Y Characteristic Data

Embedded Power for Business-Critical Continuity

OUTPUT CURRENT A
12 10
8 6 4 2 0
10 20 30 40 50 60 70 80

AMBIENT TEMPERATURE ºC

Nat conv 100 LFM 200 LFM

Figure 1 - Safe Operating Area Vin = V, VREF = V, Iout = 10 A See Note A
More datasheets: EXB50-48D3V3-1V8J | EXB50-48D05-3V3-RJ | EXB50-48D05-3V3J | PTH12060YAD | PTH05060YAD | PTH12060YAZT | PTH12060YAZ | PTH12060YAST | PTH03060YAD | PTH03060YAZ


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived PTH03060YAZT Datasheet file may be downloaded here without warranties.

Datasheet ID: PTH03060YAZT 518486