ABX00018

ABX00018 Datasheet

Code ABX00018

Part	Datasheet
ABX00018	ABX00018 (pdf)

PDF Datasheet Preview
AARDUINO MKR GSM 1400 Code ABX00018 Arduino MKR GSM 1400 is a powerful board that combines the functionality of the Zero and global GSM connectivity. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking. Please note This board does not ship with a SIM card. Arduino MKR GSM 1400 has been designed to offer a practical and cost effective solution for makers seeking to add global GSM connectivity to their projects with minimal previous experience in networking. It is based on the Atmel SAMD21 and a SARAU201 GSM module. The design includes the ability to power the board using a LiPo battery or external power source rated 5V. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the Zero board, the usual rich set of I/O interfaces, gobal GSM communication and the ease of use of the Arduino Software IDE for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power 5V to the board. During cellular transmissions the peak current required by the board will exceed 500mA. This is in excess of what can sourced by a standard USB port, so it is MANDATORY to have a 1500 mAh or higher LiPo battery plugged all the time, the current provided by the USB port will be supplmented by the battery. When powering the board using Vin, a 5V power supply that can supply atleast 2A is required.. Warning Unlike most Arduino & Genuino boards, the MKR GSM 1400 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting. TECH SPECS Microcontroller SAMD21 Cortex-M0+ 32bit low power ARM MCU Board Power Supply USB/VIN Supported Battery * 3.7V LiPo Circuit Operating Voltage 3.3V Digital I/O Pins PWM Pins 12 0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19 UART Analog Input Pins 7 ADC 8/10/12 bit Analog Output Pins 1 DAC 10 bit External Interrupts 8 0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17 DC Current per I/O Pin Flash Memory 256 KB SRAM 32 KB EEPROM Clock Speed kHz RTC , 48 MHz LED_BUILTIN Full-Speed USB Device and embedded Host Antenna power Carrier frequency 433/868/915 MHz Working region Global Length Width 25 mm Weight

PDF Datasheet Preview

AARDUINO MKR GSM 1400

Code ABX00018

Arduino MKR GSM 1400 is a powerful board that combines the functionality of the Zero and global GSM connectivity. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking. Please note This board does not ship with a SIM card.

Arduino MKR GSM 1400 has been designed to offer a practical and cost effective solution for makers seeking to add global GSM connectivity to their projects with minimal previous experience in networking. It is based on the Atmel SAMD21 and a SARAU201 GSM module. The design includes the ability to power the board using a LiPo battery or external power source rated 5V. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the Zero board, the usual rich set of I/O interfaces, gobal GSM communication and the ease of use of the Arduino Software IDE for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power 5V to the board. During cellular transmissions the peak current required by the board will exceed 500mA. This is in excess of what can sourced by a standard USB port, so it is MANDATORY to have a 1500 mAh or higher LiPo battery plugged all the time, the current provided by the USB port will be supplmented by the battery. When powering the board using Vin, a 5V power supply that can supply atleast 2A is required.. Warning Unlike most Arduino & Genuino boards, the MKR GSM 1400 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.

TECH SPECS

Microcontroller

SAMD21 Cortex-M0+ 32bit low power ARM MCU

Board Power Supply USB/VIN

Supported Battery *
3.7V LiPo

Circuit Operating Voltage
3.3V

Digital I/O Pins

PWM Pins
12 0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19

UART

Analog Input Pins
7 ADC 8/10/12 bit

Analog Output Pins
1 DAC 10 bit

External Interrupts
8 0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17

DC Current per I/O Pin

Flash Memory
256 KB

SRAM
32 KB

EEPROM

Clock Speed
kHz RTC , 48 MHz

LED_BUILTIN

Full-Speed USB Device and embedded Host

Antenna power

Carrier frequency
433/868/915 MHz

Working region

Global

Length

Width
25 mm

Weight

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ABX00018 Datasheet file may be downloaded here without warranties.

Datasheet ID: ABX00018 518328