A000024

A000024 Datasheet

Code A000024

Part	Datasheet
A000024	A000024 (pdf)

PDF Datasheet Preview
ARDUINO ETHERNET SHIELD 2 Code A000024 The Arduino Ethernet Shield 2 connects your Arduino to the internet. • The Arduino Ethernet Shield 2 connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino Board, connect it to your network with an RJ45 cable not included and follow a few simple steps to start controlling your world through the internet. As always with Arduino, every element of the platform hardware, software and documentation is freely available and This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Hundreds of thousands of Arduino Boards are already fueling people’s creativity all over the world, everyday. Join us now, Arduino is you! *Requires an Arduino Board not included • Operating voltage 5V supplied from the Arduino Board • Ethernet Controller W5500 with internal 32K buffer • Connection speed 10/100Mb • Connection with Arduino on SPI port TECH SPECS The Ethernet Shield 2 has a standard connection, with an integrated line transformer and Power over Ethernet enabled. PoE module features as follows: • IEEE802.3af compliant • Input voltage range 36V to 57V • Overload and protection • 12V Output • High efficiency DC/DC converter typ 85% 80% load • 1500V isolation input to output NB the Power over Ethernet module is proprietary hardware not made by Arduino, it is a third party accessory. For more information, see the datasheet The Shield does not come with a built in PoE module, it is a separate component that must be added on. Arduino communicates with both the W5500 and SD card using the SPI bus through the ICSP header . This is on digital pins 10, 11, 12, and 13 on the Uno and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5500 and pin 4 for the SD card. These pins cannot be used for general I/O. On the Mega, the hardware SS pin, 53, is not used to select either the W5500 or the SD card, but it must be kept as an output or the SPI interface won't work. Note that because the W5500 and SD card share the SPI bus, only one at a time can be active. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5500, set digital pin 10 as a high output. • The Shield provides a standard RJ45 Ethernet jack. • The reset button on the Shield resets both the W5500 and the Arduino Board. • The Shield contains a number of information LEDs • ON indicates that the Board and Shield are powered • LINK indicates the presence of a network link and flashes when the Shield transmits or receives data • FDX indicates that the network connection is full duplex • 100M indicates the presence of a 100 Mb/s network connection as opposed to 10 Mb/s • ACT flashes when RX or TX activity is present This shield also hosts Tinkerkit compatible connectors as follows: • 2 TinkerKit connectors for two Analog Inputs in white , connected to A2 and A3. • 2 TinkerKit connectors for two Aanlog Outputs in orange in the middle , connected to PWM outputs on pins D5 and D6. • 2 TinkerKit connectors for the TWI interface in white with 4 pins , one for input and the other one for output. OSH Schematics Arduino Ethernet Shield 2 is hardware! You can build your own board using the following files: EAGLE FILES IN .ZIP SCHEMATICS IN .PDF Previous Version Do you own a past version of this product? Check the Arduino Ethernet Shield V1 product page.

PDF Datasheet Preview

ARDUINO ETHERNET SHIELD 2

Code A000024

The Arduino Ethernet Shield 2 connects your Arduino to the internet.
• The Arduino Ethernet Shield 2 connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino Board, connect it to your network with an RJ45 cable not included and follow a few simple steps to start controlling your world through the internet. As always with Arduino, every element of the platform hardware, software and documentation is freely available and This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Hundreds of thousands of Arduino Boards are already fueling people’s creativity all over the world, everyday. Join us now, Arduino is you! *Requires an Arduino Board not included
• Operating voltage 5V supplied from the Arduino Board
• Ethernet Controller W5500 with internal 32K buffer
• Connection speed 10/100Mb
• Connection with Arduino on SPI port

TECH SPECS

The Ethernet Shield 2 has a standard connection, with an integrated line transformer and Power over Ethernet enabled.

PoE module features as follows:
• IEEE802.3af compliant
• Input voltage range 36V to 57V
• Overload and protection
• 12V Output
• High efficiency DC/DC converter typ 85% 80% load
• 1500V isolation input to output

NB the Power over Ethernet module is proprietary hardware not made by Arduino, it is a third party accessory. For more information, see the datasheet

The Shield does not come with a built in PoE module, it is a separate component that must be added on. Arduino communicates with both the W5500 and SD card using the SPI bus through the ICSP header . This is on digital pins 10, 11, 12, and
13 on the Uno and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5500 and pin 4 for the SD card. These pins cannot be used for general I/O. On the Mega, the hardware SS pin, 53, is not used to select either the W5500 or the SD card, but it must be kept as an output or the SPI interface won't work.

Note that because the W5500 and SD card share the SPI bus, only one at a time can be active. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5500, set digital pin 10 as a high output.
• The Shield provides a standard RJ45 Ethernet jack.
• The reset button on the Shield resets both the W5500 and the Arduino Board.
• The Shield contains a number of information LEDs
• ON indicates that the Board and Shield are powered
• LINK indicates the presence of a network link and flashes when the Shield transmits or
receives data
• FDX indicates that the network connection is full duplex
• 100M indicates the presence of a 100 Mb/s network connection as opposed to 10 Mb/s
• ACT flashes when RX or TX activity is present

This shield also hosts Tinkerkit compatible connectors as follows:
• 2 TinkerKit connectors for two Analog Inputs in white , connected to A2 and A3.
• 2 TinkerKit connectors for two Aanlog Outputs in orange in the middle , connected to

PWM outputs on pins D5 and D6.
• 2 TinkerKit connectors for the TWI interface in white with 4 pins , one for input and the
other one for output.

OSH Schematics

Arduino Ethernet Shield 2 is hardware! You can build your own board using the following files:

EAGLE FILES IN .ZIP SCHEMATICS IN .PDF

Previous Version

Do you own a past version of this product? Check the Arduino Ethernet Shield V1 product page.

More datasheets: SFS-800 | SFS-750 | SFS-651 | SFS-650 | SFS-550 | SFS-451 | SFS-250 | SFS-350 | SFS-250 BK | SFS-450

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived A000024 Datasheet file may be downloaded here without warranties.

Datasheet ID: A000024 518284