RAPID-UG V3804

RAPID-UG V3804 Datasheet

Profinet RapID Platform Universal Gateway

Part	Datasheet
RAPID-UG V3804	RAPID-UG V3804 (pdf)

PDF Datasheet Preview
Profinet RapID Platform Universal Gateway Connectivity Solution for 2-Port, Class B Devices The RapID Platform Universal Gateway combines all analog and digital signals for the Profinet Industrial Ethernet interface on a 45 x 25 mm form factor The gateway contains everything needed including the communications controller, protocol stacks, Flash, RAM, and analog driver so the user does not need to know anything about the Profinet protocol. All Profinet capabilities are encapsulated on this small, DIL-32 form factor device, and can be integrated into any type of automation equipment from complex control to a simple sensor or actuator. The RapID Universal Gateway connects to a “Host” processor via a UART interface or it can be operated stand-alone. In either type of operation, the Profinet communication has been Class B certified at an accredited Profinet Interface Center and tested on the bus with numerous applications to provide problem-free operation with virtually any Profinet controller. Easy Hardware and Software Integration The RapID Universal Gateway drops into a board using a standard DIL-32 form factor. Both the hardware and software interfaces are standardized and functionally identical. As a result, different RapID Universal Gateway versions are exchangeable, and by socketing the board to accept the module allows for easy configuration of other protocols. When designing-in RapID Universal Gateway, hardware integration is as easy as connecting Power/Ground/Reset, interfacing the Host processor to the UART, and hooking up to the network-side physical interface components. For stand-alone operation there is a Synchronous Serial Interface for connecting switches, analog-to-digital converters, or shift registers. Software integration with a Host processor is also easy since no re-programming is required on the Host processor and the Host firmware is never touched. The RapID Universal Gateway conforms to the Host messages passed over the UART by using a “script”. This script transforms the UART messages into the appropriate Profinet messages. Simply write a script to interpret the UART messages and the field device is ready to talk on the network. Profinet RapID Platform Universal Gateway Connectivity Solution for 2-Port, Class B Devices Easy Network Integration The Profinet RapID Universal Gateway comes with PriorityChannel technology to ensure reliable, real-time network performance. It is Class B certified and includes support for the Link Layer Discovery Protocol LLDP so controllers can identify the devices attached to the network. Also included is the Simple Network Management Protocol SNMP , along with the required Management Information Bases MIBs , to support network configuration and diagnostics. The two protocols work together so devices can be easily added or removed from the network. When a device is added to a network, it is sometimes useful to retrieve information directly from the device. A Web Server is provided for this purpose. The server can be customized to show device and company-specific information. A GSDML file is required for Profinet. This file describes a device’s capabilities to the controller. The example GSDML file provided can be tailored to describe the exact features of the final product. Easy Evaluation, Fast Product Development The Evaluation Kit available for RapID Universal Gateway provides quick assessment for interfacing a Host processor to the module. Simply connect the Host processor development board to the RapID Universal Gateway evaluation board via the UART interface. The free Protocol Developer tool is used to write a script that describes the Host processor UART messages. Once Host-side UART communication is established using the script, Profinet communication can be evaluated using 3rd-Party, PC-based Tools. The communication path between Host processor and Profinet controller Parameter Details can be completely verified before integrating the Host Processor Any CPU or DSP module into the actual hardware. Host Processor Interfaces UART up to 520 kBaud Data Transport IEEE Network Interface Data Rate 10/100 Mbps Ports 2 Environmental Conditions -40C to +85C Power Supply Voltage VDC Power consumption 1.3W TCP/IP ICMP, IGMP, ARP, SNTP, BSD 4.4A socket, DNS, BOOTP, DHCP, TELNET, server & client , CGI, SNMP Cyclic Input Data 1440 bytes Cyclic Output Data 1440 bytes Profinet Cycle time 1 ms min. Alarm Types Process, Diagnostic, Return of Sub Module DCP, LLDP, VLAN Priority Compliance RoHS, CE, PI

PDF Datasheet Preview

Profinet RapID Platform Universal Gateway

Connectivity Solution for 2-Port, Class B Devices

The RapID Platform Universal Gateway combines all analog and digital signals for the Profinet Industrial Ethernet interface on a 45 x 25 mm form factor

The gateway contains everything needed including the communications controller, protocol stacks, Flash, RAM, and analog driver so the user does not need to know anything about the Profinet protocol. All Profinet capabilities are encapsulated on this small, DIL-32 form factor device, and can be integrated into any type of automation equipment from complex control to a simple sensor or actuator. The RapID Universal Gateway connects to a “Host” processor via a UART interface or it can be operated stand-alone. In either type of operation, the Profinet communication has been Class B certified at an accredited Profinet Interface Center and tested on the bus with numerous applications to provide problem-free operation with virtually any Profinet controller.

Easy Hardware and Software Integration

The RapID Universal Gateway drops into a board using a standard DIL-32 form factor. Both the hardware and software interfaces are standardized and functionally identical. As a result, different RapID Universal Gateway versions are exchangeable, and by socketing the board to accept the module allows for easy
configuration of other protocols. When designing-in RapID Universal Gateway, hardware integration is as easy as connecting Power/Ground/Reset, interfacing the Host processor to the UART, and hooking up to the network-side physical interface components. For stand-alone operation there is a Synchronous Serial Interface for connecting switches, analog-to-digital converters, or shift registers.

Software integration with a Host processor is also easy since no re-programming is required on the Host processor and the Host firmware is never touched. The RapID Universal Gateway conforms to the Host messages passed over the UART by using a “script”. This script transforms the UART messages into the appropriate Profinet messages. Simply write a script to interpret the UART messages and the field device is ready to talk on the network.

Profinet RapID Platform Universal Gateway

Connectivity Solution for 2-Port, Class B Devices

Easy Network Integration

The Profinet RapID Universal Gateway comes with PriorityChannel technology to ensure reliable, real-time network performance. It is Class B certified and includes support for the Link Layer Discovery Protocol LLDP so controllers can identify the devices attached to the network. Also included is the Simple Network Management Protocol SNMP , along with the required Management Information Bases MIBs , to support network configuration and diagnostics. The two protocols work together so devices can be easily added or removed from the network. When a device is added to a network, it is sometimes useful to retrieve information directly from the device. A Web Server is provided for this purpose. The server can be customized to show device and company-specific information.

A GSDML file is required for Profinet. This file describes a device’s capabilities to the controller. The example GSDML file provided can be tailored to describe the exact features of the final product.

Easy Evaluation, Fast Product Development

The Evaluation Kit available for RapID Universal Gateway provides quick assessment for interfacing a Host
processor to the module. Simply connect the Host processor development board to the RapID Universal

Gateway evaluation board via the UART interface. The free Protocol Developer tool is used to write a script
that describes the Host processor UART messages. Once Host-side UART communication is established using the script, Profinet communication can be evaluated using 3rd-Party, PC-based Tools. The communication path
between Host processor and Profinet controller Parameter

Details
can be completely verified before integrating the Host Processor

Any CPU or DSP
module into the actual hardware.

Host Processor Interfaces UART up to 520 kBaud

Data Transport IEEE

Network Interface

Data Rate 10/100 Mbps

Ports 2

Environmental Conditions -40C to +85C

Power Supply

Voltage VDC Power consumption 1.3W

TCP/IP

ICMP, IGMP, ARP, SNTP, BSD 4.4A socket, DNS, BOOTP, DHCP, TELNET, server & client , CGI, SNMP

Cyclic Input Data 1440 bytes Cyclic Output Data 1440 bytes

Profinet

Cycle time 1 ms min.

Alarm Types Process, Diagnostic, Return of Sub Module

DCP, LLDP, VLAN Priority

Compliance

RoHS, CE, PI

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived RAPID-UGV3804 Datasheet file may be downloaded here without warranties.

Datasheet ID: RAPID-UGV3804 638911