114445-HMC585MS8G

114445-HMC585MS8G Datasheet

List of Materials for Evaluation PCB 114445 [1]

Part	Datasheet
114445-HMC585MS8G	114445-HMC585MS8G (pdf)

Related Parts	Information
HMC585MS8GE	HMC585MS8GE

PDF Datasheet Preview
HMC585MS8G / 585MS8GE v01.0907 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 400 - 650 MHz The HMC585MS8G / HMC585MS8GE are ideal for: • Basestations & Repeaters • GSM, GPRS & EDGE • CDMA & W-CDMA • Cable Modem Termination Systems Functional Diagram High Input IP3 +33 dBm Conversion Loss 9 dB Low LO Drive -2 to +4 dBm Single Supply +5V 50 mA Compact MSOP Package 14.8mm2 The HMC585MS8G & HMC585MS8GE are high dynamic range passive MMIC mixers with integrated LO amplifiers in plastic surface mount 8 lead Mini Small Outline Packages MSOP covering an RF range of 400 MHz to 650 MHz. The LO range of 300 MHz to 750 MHz supports both high side and low side LO applications. Excellent input IP3 performance of +33 dBm for down conversion and +27 dBm for up conversion is provided for 2.5G & 3G applications at an LO drive of 0 dBm. RF conversion loss is 9 dB typical. The DC to 250 MHz IF frequency response will satisfy a wide range of Tx and Rx frequency plans. MIXERS - HIGH IP3 - SMT Electrical Specifications, TA = +25°C, LO = 0 dBm, IF = 50 MHz, Vdd= 5V Parameter Min. Typ. Max. Frequency Range, RF 400 - 650 Frequency Range, LO 300 - 750 Frequency Range, IF Conversion Loss LO to RF Isolation LO to IF Isolation IP3 Input 1 dB Gain Compression Input LO Input Drive Level Typical -2 to +4 Supply Current Unless otherwise noted, all measurements performed as a downconverter, with high side LO & IF = 50 MHz. Units MHz GHz dB dBm mA 9 - 356 For price, delivery, and to place orders, please contact Hittite Microwave Corporation 20 Alpha Road, Chelmsford, MA 01824 Phone 978-250-3343 Fax 978-250-3373 Order On-line at HMC585MS8G / 585MS8GE v01.0907 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 400 - 650 MHz Conversion Gain vs. Temperature LO = 0 dBm CONVERSION GAIN dB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material Rogers 4350 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation 20 Alpha Road, Chelmsford, MA 01824 Phone 978-250-3343 Fax 978-250-3373 Order On-line at 9 - 363

PDF Datasheet Preview

HMC585MS8G / 585MS8GE
v01.0907

HIGH IP3 GaAs MMIC MIXER with

INTEGRATED LO AMPLIFIER, 400 - 650 MHz

The HMC585MS8G / HMC585MS8GE are ideal for:
• Basestations & Repeaters
• GSM, GPRS & EDGE
• CDMA & W-CDMA
• Cable Modem Termination Systems

Functional Diagram

High Input IP3 +33 dBm Conversion Loss 9 dB Low LO Drive -2 to +4 dBm Single Supply +5V 50 mA Compact MSOP Package 14.8mm2

The HMC585MS8G & HMC585MS8GE are high dynamic range passive MMIC mixers with integrated LO amplifiers in plastic surface mount 8 lead Mini Small Outline Packages MSOP covering an RF range of 400 MHz to 650 MHz. The LO range of 300 MHz to 750 MHz supports both high side and low side LO applications. Excellent input IP3 performance of +33 dBm for down conversion and +27 dBm for up conversion is provided for 2.5G & 3G applications at an LO drive of 0 dBm. RF conversion loss is 9 dB typical. The DC to 250 MHz IF frequency response will satisfy a wide range of Tx and Rx frequency plans.

MIXERS - HIGH IP3 - SMT

Electrical Specifications, TA = +25°C, LO = 0 dBm, IF = 50 MHz*, Vdd= 5V

Parameter

Min.

Typ.

Max.

Frequency Range, RF
400 - 650

Frequency Range, LO
300 - 750

Frequency Range, IF

Conversion Loss

LO to RF Isolation

LO to IF Isolation

IP3 Input
1 dB Gain Compression Input

LO Input Drive Level Typical
-2 to +4

Supply Current
*Unless otherwise noted, all measurements performed as a downconverter, with high side LO & IF = 50 MHz.

Units MHz GHz dB dBm mA
9 - 356

For price, delivery, and to place orders, please contact Hittite Microwave Corporation 20 Alpha Road, Chelmsford, MA 01824 Phone 978-250-3343 Fax 978-250-3373 Order On-line at

HMC585MS8G / 585MS8GE
v01.0907

HIGH IP3 GaAs MMIC MIXER with

INTEGRATED LO AMPLIFIER, 400 - 650 MHz

Conversion Gain vs. Temperature LO = 0 dBm

CONVERSION GAIN dB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material Rogers 4350

The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.

For price, delivery, and to place orders, please contact Hittite Microwave Corporation 20 Alpha Road, Chelmsford, MA 01824 Phone 978-250-3343 Fax 978-250-3373 Order On-line at
9 - 363

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 114445-HMC585MS8G Datasheet file may be downloaded here without warranties.

Datasheet ID: 114445-HMC585MS8G 517952