ADG406/ADG407/ADG426
Part | Datasheet |
---|---|
![]() |
ADG426BRSZ-REEL7 (pdf) |
PDF Datasheet Preview |
---|
LC2MOS 8-/16-Channel High Performance Analog Multiplexers ADG406/ADG407/ADG426 44 V supply maximum ratings VSS to VDD analog signal range Low on resistance 80 Ω maximum Low power Fast switching tON < 160 ns tOFF < 150 ns Break-before-make switching action Audio and video routing Automatic test equipment Data acquisition systems Battery powered systems Sample hold systems Communication systems Avionics PRODUCT HIGHLIGHTS Extended Signal Range. The ADG406/ADG407/ADG426 are fabricated on an enhanced LC2MOS process giving an increased signal range which extends to the supply rails. Low Power Dissipation. Low RON. Single/Dual Supply Operation. Single Supply Operation. For applications where the analog signal is unipolar, the ADG406/ADG407/ADG426 can be operated from a single rail power supply. The parts are fully specified with a single +12 V power supply and remain functional with single supplies as low as +5 V. FUNCTIONAL BLOCK DIAGRAMS ADG406 S16 1 OF 16 DECODER A0 A1 A2 A3 EN Figure ADG407 S1A DA S1B DB S8B 1 OF 8 DECODER A0 A1 A2 EN Figure ADG426 00026-001 00026-002 DECODER/ LATCHES A0 A1 A2 A3 EN RS Figure 00026-003 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: Fax Analog Devices, Inc. All rights reserved. ADG406/ADG407/ADG426 TABLE OF CONTENTS Dual Supply 4 Single Supply 6 0 Initial Version ADG426 Timing Absolute Maximum Ratings ESD Pin Configurations and Function Descriptions Typical Performance Characteristics 12 Test 15 Terminology 18 Outline Dimensions 19 Ordering Guide 20 The ADG406, ADG407, and ADG426 are monolithic CMOS analog multiplexers. The ADG406 and ADG426 switch one of sixteen inputs to a common output as determined by the 4-bit binary address lines A0, A1, A2, and A3. The ADG426 has on-chip address and control latches that facilitate microprocessor interfacing. The ADG407 switches one of eight differential inputs to a common differential output as determined by the 3-bit binary address lines A0, A1 and A2. An EN input on all devices is used to enable or disable the device. When disabled, all channels are switched off. ADG406/ADG407/ADG426 The ADG406/ADG407/ADG426 are designed on an enhanced LC2MOS process that provides low power dissipation yet gives high switching speed and low on resistance. These features make the parts suitable for high speed data acquisition systems and audio signal switching. Low power dissipation makes the parts suitable for battery powered systems. Each channel conducts equally well in both directions when on and has an input signal range which extends to the supplies. In the off condition, signal levels up to the supplies are blocked. All channels exhibit breakbefore-make switching action preventing momentary shorting when switching channels. Inherent in the design is low charge injection for minimum transients when switching the digital inputs. ADG406/ADG407/ADG426 SPECIFICATIONS DUAL SUPPLY VDD = +15 V ± 10%, VSS = −15 V ± 10%, GND = 0 V, unless otherwise noted. Table Parameter1 ANALOG SWITCH Analog Signal Range RON RON Match LEAKAGE CURRENTS Source Off Leakage IS Off Drain Off Leakage ID Off ADG406, ADG426 ADG407 Channel On Leakage ID, IS On ADG406, ADG426 ADG407 DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current IINL or IINH CIN, Digital Input Capacitance DYNAMIC CHARACTERISTICS2 tTRANSITION Break Before Make Delay, tOPEN +25°C −40°C to +85°C Unit Test Conditions/Comments VSS to VDD ±20 ±20 ±20 ±20 ±20 V Ω typ Ω max Ω typ nA max nA max nA max nA max nA max VD = ±10 V, IS = −1 mA VDD = V, VSS = V VD = 0 V, IS = −1 mA VDD = V, VSS = V VD = ±10 V, VS = +10 V, see Figure 26 VD = ±10 V, VS = +10 V see Figure 27 VS = VD = ±10 V see Figure 28 V min V max ±1 8 uA max VIN = 0 or VDD pF typ f = 1 MHz 150 250 ns typ ns max ns min RL = 300 Ω, CL = 35 pF V1 = ±10 V, V2 = +10 V see Figure 29 RL = 300 Ω, CL = 35 pF VS = +5 V, see Figure 30 tON EN, WR 120 175 160 225 tOFF EN, RS 110 130 150 180 ADG426 Only ORDERING GUIDE Model1 ADG406BN ADG406BNZ ADG406BP-REEL ADG406BPZ-REEL ADG407BN ADG407BNZ ADG407BP-REEL ADG407BPZ-RL ADG407BCHIPS ADG426BN ADG426BNZ ADG426BRS-REEL ADG426BRS-REEL7 ADG426BRSZ-REEL Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 28-Lead PDIP 28-Lead PDIP 28-Lead PLCC 28-Lead PLCC 28-Lead PLCC 28-Lead PLCC 28-Lead PDIP 28-Lead PDIP 28-Lead PLCC 28-Lead PLCC 28-Lead PLCC 28-Lead PLCC 28-Lead PDIP 28-Lead PDIP 28-Lead SSOP 28-Lead SSOP 28-Lead SSOP 28-Lead SSOP 28-Lead SSOP 1 Z = RoHS Compliant Part. 2 N = Plastic DIP, P = Plastic Leaded Chip Carrier PLCC , RS = Shrink Small Outline Package SSOP . Package Option2 N-28-2 N-28-2 P-28 P-28 P-28 P-28 N-28-2 N-28-2 P-28 P-28 P-28 P-28 DIE N-28-2 N-28-2 RS-28 RS-28 RS-28 RS-28 RS-28 060106-A Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D00026-0-5/10 B |
More datasheets: 74ACT241MTC | 74ACT241MTCX | 74ACT241PC | 74ACT241SCX | 74AC241SJX | 74AC241SJ | 74AC241SCX | 74ACT241SC | 74ACT241SJX | 74ACT241SJ |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ADG426BRSZ-REEL7 Datasheet file may be downloaded here without warranties.