R13MP

R13MP Datasheet

IDS-R13MP

Part	Datasheet
R13MP	R13MP (pdf)

PDF Datasheet Preview
IDS-R13MP MHz RFID Reader IC Multi-Protocol Including ISO 14443, ISO 15693, and cool-Log Key Features Supply voltage range to 5.5V Protocols ISO/IEC 15693, ISO 14443A/B1 and cool-Log Antenna driver using OOK or ASK Dual receiver input providing both AM and PM demodulation avoiding communication holes Reception automatic gain control 3.3V voltage regulator providing up to 20 mA for external MCU High output power 100 or 200 mW from single 5V supply Significant increase of PSRR through on-chip RF output supply regulator Reader to reader anti-collision Power-down, standby and active mode Temperature range -40°C to 110°C Block Diagram The IDS-R13MP is an integrated analogue front end and data framing system for 13.56MHz RFID reader systems. The built-in programming options make it suitable for a wide range of applications both in proximity and vicinity RFID systems. The reader configuration is achieved by selecting the desired protocol in the control registers. The direct access to all control registers also allows fine-tuning of different reader parameters if needed. Applications MHz RFID systems: ° Proximity systems ° Vicinity systems ° Data logging systems ° High bit rate proximity systems Package 32-pin QFN 5 x 5mm RoHS 1 Purchase of IDS-R13MP does not imply any agreement with any third party patent holder or any grant of any ISO14443A or -B licenses. Customers are solely liable for any infringement of third party’s rights and therefore advised to sign patent licensing agreements with all third parties! See disclaimer at end of document. IDS-R13MP_SD-02.doc • June 2009 IDS Microchip AG 2•8 IDS-R13MP • MHz RFID Reader Content 1 Key Characteristics and Benefits 3 2 Pin Configuration 3 Short Description 4 Absolute Maximum Ratings 4 5 Operating Conditions 5 6 5 7 Package Outline 7 8 Ordering 8 Figures Figure 1 32-Pin QFN Pinout Top View 3 Figure 2 Matching Circuit 4 ohm to 50 ohm 5 Figure 3 Typical 6 1 Related Documents Specification full data sheet IDS-R13MP_DS IDS-R13MP_SD-02.doc • June 2009 IDS Microchip AG IDS-R13MP • MHz RFID Reader 2 Key Characteristics and Benefits ISO 14443, ISO 15693, Tag-it, ISO14443 high bit rates, FeliCa and cool-Log compatibility Integrated low level transmission coding 1 out of 4, 1 out of 256, modified miller 106Kb/s, NRZ 106Kb/s , Tag-it, FeliCa and cool-Log compatible Integrated sub-carrier decoders for ISO 15693, ISO14443 A and B, ISO14443 high bit rates, Tag-it, Felica and cool-Log protocols Integrated data framing for ISO 15693, ISO14443 A and B, ISO14443 high bit rates, Tag-it, FeliCa and cool-Log protocols. Integrated CRC and/or parity checking for ISO 15693, ISO14443 A and B, ISO14443 high bit rates, Tag-it, FeliCa and cool-Log protocols Parallel 8 bit or serial 4 pin SPI interface with MCU using 12 bytes FIFO Voltage range for communication to MCU between 1.8V and 5.5V Synchronization clock output selectable as RF frequency, RF/2 or RF/4 frequency Operating range from 2.7V to 5.5V Integrated supply voltage regulator 20mA which can be used to supply MCU and other external circuitry 3 Pin Configuration 3•8 Integrated supply voltage regulator for the RF output stage, providing rejection to supply noise High output power 100mW or 200mW from single 5V supply Antenna driver using OOK or ASK modulation Adjustable ASK modulation range 8% to 30% Dual receiver input comprising AM & PM demodulation ensuring no “communication holes” ISO sub-carrier receiving and decoding compatibility 212kHz, 424kHz, and 848kHz Built in reception low-pass and high-pass filters having selectable corner frequencies. Selectable reception gain Reception automatic gain control Reception RSSI measurement for AM and PM signal 3 bit Measurement of external RF fields for reader to reader anti-collision Self diagnostic of the system through measurement of RF input level Oscillator using 13.56MHz quartz Power down, standby and active mode Extended temperature range -40°C to 110°C Figure 1 32-Pin QFN Pinout Top View IDS-R13MP_SD-02.doc • June 2009 IDS Microchip AG 4•8 IDS-R13MP • MHz RFID Reader 4 Short Description The IDS-R13MP is an integrated analogue front end and data framing system for a 13.56MHz RFID reader system. Built-in programming options make it suitable for a wide range of applications both in proximity and vicinity RFID systems. The reader configuration is achieved by selecting the desired protocol in the control registers. Direct access to all control registers also allows finetuning of different reader parameters if needed. Parallel or serial interface can be selected for communication between MCU and reader. When hardware coders and decoders are used accelerators for different standards , transmission and receive function use the 12-bytes FIFO register. In case of direct transmission or reception, coders and decoders are bypassed and MCU has to service reader in real time. The transmitter generates 100mW or 200mW output power into load at 5V supply and is capable of OOK or ASK modulation. The integrated supply voltage regulators ensure supply rejection of the complete reader system. The transmission system comprises low level coding for 1 out of 4 and 1 out of 256 for ISO15693, modified Miller for ISO14443A and high bit rate systems, Tag-it encoding. For all these systems the automatic generation of SOF and EOF, CRC and/or parity is supported. The receiver system enables AM and PM demodulation using a dual input system patent pending . The receiver also comprises automatic gain control option also patent pending and selectable gain and signal bandwidth to cover a range of input sub-carriers signal options. The signal strength of AM and PM modulation is measured and can be accessed in RSSI register. The receiver output is selectable between digitized sub-carrier signal and any of eleven integrated sub-carrier decoders two for ISO 15693 high bit rate, two for ISO15693 low bit rate, two for ISO 14443, three for ISO14443 high bit rates, one for Tag-it system . Selected decoders deliver bit stream and data clock as outputs. The receiver system also comprises framing system. This system performs the CRC and/or parity check, removes the EOF and SOF strings and organizes the data in bytes. Framed data is accessible to MCU through a 12-byte FIFO register and MCU interface. The framing is supported for ISO15693 and ISO14443. To support external MCU and other circuitry a 3.3V regulated supply output and synchronization clock output are available. The regulated supply has a source current capability of 20mA. 5 Absolute Maximum Ratings Operating temperature range, unless otherwise noted * Supply Voltage Range VEXT see Note V to 6 V Maximum Positive Voltage - Other VSUP + 0.3V Maximum Negative Voltage - Other Pads ESDS Rating, HBM Human Body Model 2 kV ESDS Rating, CDM Charged Device 500V ESDS Rating, MM Machine 200V Maximum Operating Virtual Junction Temperature, TJ 140°C Storage Temperature, -55°C to +150°C Lead Temperature mm from case for 10 300ºC Stresses beyond those listed under »Absolute Maximum may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under »Operating are not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 9 Ordering Information ORDERING CODE OPERATING PACKAGE TEMPERATURE RANGE TYPE DEVICE MARKING SHIPPING FORM IDS-R13MP MHz Multi-Protocol RFID Reader IC -40°C to 110°C QFN32 5 x 5 mm RoHS IDS R13MP Mini Tape & Reel 250/reel * Pb-Free RoHS compatible , and free of Bromine Br and Antimony Sb based flame retardants Br or Sb do not exceed by weight in homogeneous material . Order quantities should be a multiple of shipping form. Sales & Marketing Office IDS Microchip AG Wächlenstrasse 5, CH-8832 Wollerau, Switzerland Phone +41 43 844 6253 Fax +41 43 844 6250 Sales & Marketing Americas IC Magic Inc. 34 Granlea Rd, North York, ON M2N 2Z5, Canada Phone +416 227 9196 Fax +41 43 844 6250 cool-Log is a registered trademark of IDS Microchip AG. Tag-it is a registered trademark of Texas Instruments, Inc. IDS reserves the right to change or discontinue such products without notice. The information furnished here by IDS is believed to be correct and accurate as of the publication date. However, IDS shall not be liable to any third party for any damages, including but no limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental, or consequential damages of any kind in connection with or arising out of the furnishing, performance, or use of the technical data. No obligation or liability to any third party shall arise or flow out of IDS' rendering technical or other services. Products sold by IDS are covered exclusively by the IDS standard warranty, patent indemnification, and other provisions appearing in IDS standard "Terms of Sale". Testing and other quality control techniques are used to the extent IDS deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. IDS makes no warranty express, statutory, implied and/or by description , including without limitation any warranties of merchantability and/or fitness for a particular purpose, regarding the information set forth in the Materials pertaining to IDS products, or regarding the freedom of any products described in the Materials from patent and/or other infringement. Purchase of IDS-R13MP does not imply any agreement with any third party patent holder or any grant of any ISO14443A or -B licenses. Customers are solely liable for any infringement of third party’s rights and therefore advised to sign patent licensing agreements with all third parties! IDS reserves the right to discontinue production and change specifications and prices, make corrections, modifications, enhancements, improvements and other changes of its products and services at any time without notice. IDS products are intended for use in commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment, are specifically not recommended without additional mutually agreed upon processing by IDS for such applications. IDS assumes no liability for application assistance or customer product design. Customers are responsible for their products and applications using IDS components. IDS-R13MP_SD-02.doc • June 2009 IDS Microchip AG

PDF Datasheet Preview

IDS-R13MP

MHz RFID Reader IC

Multi-Protocol Including ISO 14443, ISO 15693, and cool-Log

Key Features Supply voltage range to 5.5V Protocols ISO/IEC 15693, ISO 14443A/B1 and
cool-Log Antenna driver using OOK or ASK Dual receiver input providing both AM and PM
demodulation avoiding communication holes Reception automatic gain control 3.3V voltage regulator providing up to 20 mA
for external MCU High output power 100 or 200 mW from single
5V supply Significant increase of PSRR through on-chip

RF output supply regulator Reader to reader anti-collision Power-down, standby and active mode Temperature range -40°C to 110°C

Block Diagram

The IDS-R13MP is an integrated analogue front end and data framing system for 13.56MHz RFID reader systems. The built-in programming options make it suitable for a wide range of applications both in proximity and vicinity RFID systems.

The reader configuration is achieved by selecting the desired protocol in the control registers. The direct access to all control registers also allows fine-tuning of different reader parameters if needed.

Applications MHz RFID systems:
° Proximity systems ° Vicinity systems ° Data logging systems ° High bit rate proximity systems

Package
32-pin QFN 5 x 5mm RoHS
1 Purchase of IDS-R13MP does not imply any agreement with any third party patent holder or any grant of any ISO14443A or -B licenses. Customers are solely liable for any infringement of third party’s rights and therefore advised to sign patent licensing agreements with all third parties! See disclaimer at end of document.

IDS-R13MP_SD-02.doc
• June 2009 IDS Microchip AG
2•8

IDS-R13MP
• MHz RFID Reader

Content
1 Key Characteristics and Benefits 3 2 Pin Configuration 3 Short Description 4 Absolute Maximum Ratings 4 5 Operating Conditions 5 6 5 7 Package Outline 7 8 Ordering 8

Figures

Figure 1 32-Pin QFN Pinout Top View 3 Figure 2 Matching Circuit 4 ohm to 50 ohm 5 Figure 3 Typical 6
1 Related Documents

Specification full data sheet IDS-R13MP_DS

IDS-R13MP_SD-02.doc
• June 2009 IDS Microchip AG

IDS-R13MP
• MHz RFID Reader
2 Key Characteristics and Benefits

ISO 14443, ISO 15693, Tag-it, ISO14443 high bit rates, FeliCa and cool-Log compatibility

Integrated low level transmission coding 1 out of 4, 1 out of 256, modified miller 106Kb/s, NRZ 106Kb/s , Tag-it, FeliCa and cool-Log compatible

Integrated sub-carrier decoders for ISO 15693, ISO14443 A and B, ISO14443 high bit rates, Tag-it, Felica and cool-Log protocols

Integrated data framing for ISO 15693, ISO14443 A and B, ISO14443 high bit rates, Tag-it, FeliCa and cool-Log protocols.

Integrated CRC and/or parity checking for ISO 15693, ISO14443 A and B, ISO14443 high bit rates, Tag-it, FeliCa and cool-Log protocols

Parallel 8 bit or serial 4 pin SPI interface with MCU using 12 bytes FIFO

Voltage range for communication to MCU between 1.8V and 5.5V

Synchronization clock output selectable as RF frequency, RF/2 or RF/4 frequency

Operating range from 2.7V to 5.5V Integrated supply voltage regulator 20mA
which can be used to supply MCU and other external circuitry
3 Pin Configuration
3•8

Integrated supply voltage regulator for the RF output stage, providing rejection to supply noise

High output power 100mW or 200mW from single 5V supply

Antenna driver using OOK or ASK modulation Adjustable ASK modulation range 8% to 30% Dual receiver input comprising AM & PM
demodulation ensuring no “communication holes” ISO sub-carrier receiving and decoding compatibility 212kHz, 424kHz, and 848kHz Built in reception low-pass and high-pass filters having selectable corner frequencies. Selectable reception gain Reception automatic gain control Reception RSSI measurement for AM and PM signal 3 bit Measurement of external RF fields for reader to reader anti-collision Self diagnostic of the system through measurement of RF input level Oscillator using 13.56MHz quartz Power down, standby and active mode Extended temperature range -40°C to 110°C

Figure 1 32-Pin QFN Pinout Top View

IDS-R13MP_SD-02.doc
• June 2009 IDS Microchip AG
4•8

IDS-R13MP
• MHz RFID Reader
4 Short Description

The IDS-R13MP is an integrated analogue front end and data framing system for a 13.56MHz RFID reader system. Built-in programming options make it suitable for a wide range of applications both in proximity and vicinity RFID systems.

The reader configuration is achieved by selecting the desired protocol in the control registers. Direct access to all control registers also allows finetuning of different reader parameters if needed.

Parallel or serial interface can be selected for communication between MCU and reader. When hardware coders and decoders are used accelerators for different standards , transmission and receive function use the 12-bytes FIFO register. In case of direct transmission or reception, coders and decoders are bypassed and MCU has to service reader in real time.

The transmitter generates 100mW or 200mW output power into load at 5V supply and is capable of OOK or ASK modulation. The integrated supply voltage regulators ensure supply rejection of the complete reader system.

The transmission system comprises low level coding for 1 out of 4 and 1 out of 256 for ISO15693, modified Miller for ISO14443A and high bit rate systems, Tag-it encoding. For all these systems
the automatic generation of SOF and EOF, CRC and/or parity is supported.

The receiver system enables AM and PM demodulation using a dual input system patent pending . The receiver also comprises automatic gain control option also patent pending and selectable gain and signal bandwidth to cover a range of input sub-carriers signal options. The signal strength of AM and PM modulation is measured and can be accessed in RSSI register. The receiver output is selectable between digitized sub-carrier signal and any of eleven integrated sub-carrier decoders two for ISO 15693 high bit rate, two for ISO15693 low bit rate, two for ISO 14443, three for ISO14443 high bit rates, one for Tag-it system . Selected decoders deliver bit stream and data clock as outputs.

The receiver system also comprises framing system. This system performs the CRC and/or parity check, removes the EOF and SOF strings and organizes the data in bytes. Framed data is accessible to MCU through a 12-byte FIFO register and MCU interface. The framing is supported for ISO15693 and ISO14443.

To support external MCU and other circuitry a 3.3V regulated supply output and synchronization clock output are available. The regulated supply has a source current capability of 20mA.
5 Absolute Maximum Ratings

Operating temperature range, unless otherwise noted * Supply Voltage Range VEXT see Note V to 6 V Maximum Positive Voltage - Other VSUP + 0.3V Maximum Negative Voltage - Other Pads ESDS Rating, HBM Human Body Model 2 kV ESDS Rating, CDM Charged Device 500V ESDS Rating, MM Machine 200V Maximum Operating Virtual Junction Temperature, TJ 140°C Storage Temperature, -55°C to +150°C Lead Temperature mm from case for 10 300ºC
*Stresses beyond those listed under »Absolute Maximum may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under »Operating are not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
9 Ordering Information
ORDERING CODE

OPERATING

PACKAGE

TEMPERATURE RANGE

TYPE

DEVICE MARKING

SHIPPING FORM

IDS-R13MP

MHz Multi-Protocol RFID Reader IC
-40°C to 110°C

QFN32 5 x 5 mm

RoHS*

IDS R13MP

Mini Tape & Reel 250/reel
* Pb-Free RoHS compatible , and free of Bromine Br and Antimony Sb based flame retardants Br or Sb do not exceed by weight in homogeneous material .

Order quantities should be a multiple of shipping form.

Sales & Marketing Office IDS Microchip AG Wächlenstrasse 5, CH-8832 Wollerau, Switzerland Phone +41 43 844 6253 Fax +41 43 844 6250

Sales & Marketing Americas IC Magic Inc. 34 Granlea Rd, North York, ON M2N 2Z5, Canada Phone +416 227 9196 Fax +41 43 844 6250
cool-Log is a registered trademark of IDS Microchip AG.

Tag-it is a registered trademark of Texas Instruments, Inc.

IDS reserves the right to change or discontinue such products without notice.

The information furnished here by IDS is believed to be correct and accurate as of the publication date. However, IDS shall not be liable to any third party for any damages, including but no limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental, or consequential damages of any kind in connection with or arising out of the furnishing, performance, or use of the technical data. No obligation or liability to any third party shall arise or flow out of IDS' rendering technical or other services.

Products sold by IDS are covered exclusively by the IDS standard warranty, patent indemnification, and other provisions appearing in IDS standard "Terms of Sale". Testing and other quality control techniques are used to the extent IDS deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. IDS makes no warranty express, statutory, implied and/or by description , including without limitation any warranties of merchantability and/or fitness for a particular purpose, regarding the information set forth in the Materials pertaining to IDS products, or regarding the freedom of any products described in the Materials from patent and/or other infringement. Purchase of IDS-R13MP does not imply any agreement with any third party patent holder or any grant of any ISO14443A or -B licenses. Customers are solely liable for any infringement of third party’s rights and therefore advised to sign patent licensing agreements with all third parties!

IDS reserves the right to discontinue production and change specifications and prices, make corrections, modifications, enhancements, improvements and other changes of its products and services at any time without notice. IDS products are intended for use in commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment, are specifically not recommended without additional mutually agreed upon processing by IDS for such applications. IDS assumes no liability for application assistance or customer product design. Customers are responsible for their products and applications using IDS components.

IDS-R13MP_SD-02.doc
• June 2009 IDS Microchip AG

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived R13MP Datasheet file may be downloaded here without warranties.

Datasheet ID: R13MP 519799