AS3681
Part | Datasheet |
---|---|
![]() |
AS3681 DB (pdf) |
PDF Datasheet Preview |
---|
austriamicrosystems AS3681 Power & Lighting Management Unit 1 General Description The AS3681 is a highly-integrated, ultra-flexible CMOS Power- and Lighting Management Unit to supply power to LCD- and camera-modules in mobile telephones, and other 1-cell Li+ or 3-cell NIMH powered devices. The AS3681 incorporates one low-power, low-dropout regulator LDO , one Step Up DC/DC Converter for white backlight LEDs, one high-power Charge Pump for camera flash LEDs, one Analog-to-Digital Converter, support for up to 11 current sinks, a serial interface, and control logic all onto a single die. The linear analog regulator features extremely high analog performance regarding: ! Noise < 30µVrms from 100Hz to 100kHz ! Line/load Regulation <1mV Static and <20mV Transient ! Power Supply Rejection ! Ultra-Low Power Consumption 1µA Shutdown, 6µA Standby LDO output voltages and output currents are programmable via a serial interface. 2 Key Features ! Programmable High-Performance Regulator - Low-Noise LDO to 3.4V, 100mA - 2.8V Default Output Voltage after Power-up - 3µA Quiescent Current in Standby Iout <5mA - Turns On/Off with Rising/Falling Edge of GPIO Supply Voltage - Programmable via Serial Interface ! High-Efficiency Step Up DC/DC Converter - Up to 25V/50mA for White LEDs - Programmable Output Voltage with External Resistors and Serial Interface ! High-Efficiency High-Power Charge Pump - 1:1, and 2:1 Mode - Output Current up to 400mA - Efficiency up to 95% - Only 4 External Capacitors Required 2 x 1µF Flying Capacitors, 2 x 2.2µF Input/Output Capacitors - Supports LCD White Backlight LEDs, Camera Flash White LEDs, and Keypad Backlight LEDs ! Supports up to 11 Current Sinks - Three Programmable 4-bit from 10 to 150mA resp. 300mA - Two Programmable 4-bit from to mA - Three Programmable 4-bit from to mA for RGB LEDs - Three Programmable 4-bit from to 37.5mA for General Purpose Applications - Programmable Hardware Control Strobe, PWM - Selectively Enable/Disable Current Sinks ! 10-bit Successive Approximation ADC - 11µs Conversion Time - Two Selectable Inputs GPIO0 and GPIO1 ! Four General Purpose Inputs/Outputs - Digital Input, Digital Output, and Tristate - Programmable Pull-Up, and Pull-Down - GPIO2 can be used as Camera Flash Strobe ! Negative or High-Voltage Charge Pump - Regulated Output Voltage, Programmable by Dual Resistors e.g. -6V, 10mA for OLED or ±15V, 5mA for TFT - ± 5% Accuracy - Requires Few External Components ! Standby LDO - Regulated 2.5V - Maximum Output Current 10mA - Always On Supplies Internal Digital Blocks - 3µA Quiescent Current ! Wide Battery Supply Range to 5.5V ! Serial Interface Control ! On-Chip Bandgap Tuning for High Accuracy ±1% ! Overcurrent and Thermal Protection ! 32-Pin, Small Form-Factor QFN Package 5 x 5 x 1mm, 0.5mm pitch , Enhanced Thermal Characteristics ! 1 Watt Power Dissipation TAmbient = 70ºC 3 Application Power- and lighting-management for mobile telephones and other 1-cell Li+ or 3-cell NiMH powered devices. 1997-2004, austriamicrosystems USA, Inc. 8601 Six Forks Road, Suite 400 Raleigh,NC 27615 USA. All Rights Reserved. AS3681 Product Brief austriamicrosystems 4 Block Diagrams Figure Option by software Step Up DC/DC Converter Pins 23, 24, 28, 29 and External Charge Pump Pins 25, 26, Battery AS3681 Power Management Unit C2 1µF LDO e.g. 2.8V C3 2.2µF 2.5V C4 1µF |
More datasheets: 8193 | CYV15G0103EQ-LXC | 1077 | SA028 | PE300B-10FM | FR804 | FR803 | FR802 | FR801 | FR805 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AS3681 DB Datasheet file may be downloaded here without warranties.