HT-2234

HT-2234 Datasheet

Hand Tool Part Number HT-2234 22 - 30 AWG

Part	Datasheet
HT-2234	HT-2234 (pdf)

PDF Datasheet Preview
DUBOXTM LOOSE PIECE HAND TOOL Hand Tool Part Number HT-2234 22 - 30 AWG For termination Of DuboxTM 76357-x01LF Terminals FCI MANUAL P/N 10123594-9090 FCI USA, Inc. Issued Date 12/20/2012 Manual P/N 10123594-9090 Page 1 of 9 FCI USA, Inc. Issued Date 12/20/2012 HT-2234 HAND TOOL Table of Contents HAND TOOL TABLE OF CONTENTS INTRODUCTION SCOPE OF HAND TOOL FEATURES SPECIFICATIONS CRIMP SAFETY SETTING UP THE HAND TOOL ATTACHING THE TOOL HEAD CRIMPING PROCEEDURES LOADING THE DUBOXTM TERMINAL 7 CRIMPING PROCESS 8 TERMINAL HOLDER ADJUSTMENT ALIGNMENT 9 ROUTINE MAINTENANCE PARTS REPLACEMENT REFERENCE DRAWINGS TA-317 REFERENCE DOCUMENTS FORM #E-3245 - -Customer Application Machine Warranty and Service Policy “Section I” Equipment owned by FCI USA LLC. FORM #E-3244 - -Customer Application Machine Warranty and Service Policy “Section II” Equipment purchased by the customer. FORM # E-3247- - FCI Electronics Address List Data herein have been verified and validated and are believed adequate for the intended use of the applicator. If the applicator or procedures are used for purposes over and above the capabilities specified herein, confirmation of their validity and suitability should be obtained otherwise, FCI USA LLC does not guarantee results and assumes no obligation or liability. This publication is not a license to operate under, nor a recommendation to infringe upon, any process patents. FCI USA, Inc. Issued Date 12/20/2012 Manual P/N 10123594-9090 Page 3 of 9 INTRODUCTION SCOPE OF MANUAL: This manual contains the information necessary to understand, install, operate and maintain the HT-2234 DuboxTM hand tools. This information is intended for the use by both the operator and service personnel. However, certain procedures within the manual should be performed by service personnel only. These procedures are identified by a warning instruction. Refer to the table of contents for a breakdown of each subject matter covered in each section. WARNINGS, CAUTIONS, and NOTES within the text of this manual are used to emphasize important and critical instructions. WARNING An operating procedure, practice, etc. which if not carefully followed, could result in personal injury, or affect the operator’s health. CAUTION An operating procedure, practice, etc. which, if not strictly observed, could result in damage of equipment. NOTE An operating procedure, condition, etc. which it is essential to highlight. We recommend that the operators and service personnel responsible for maintenance of the FCI hand tools become thoroughly familiar with all aspects of the hand tool construction and operation. If operational or maintenance problems arise which are beyond the scope of this manual, contact your district service representative. HAND TOOL FEATURES: The HT-2234 Designed to terminate a single 22 30 awg pre-stripped discrete wire to a loose-piece 22 30 awg DuboxTM terminal, P/N 76357-x01LF. Two sets of crimp tooling are provided One set is used to terminate 22 24 awg wires while the other is utilized to terminate 26 - 30 awg wires. Labeling above each set of crimp tooling indicates the appropriate wire range for that location. The HT-2234 hand tool used to ergonomically terminate 1 crimp per cycle without lengthy set-up times. • A terminal holder is provided with two cavities that correspond to the conductor size being terminated. • Ratcheting handle ensures the complete crimping process has been fully completed and can be released if required. • Spring-loaded wire-stops are installed on each tooling cavity to assist with correct wire placement. • The tool head can be easily separated from the handles for cleaning and tool maintenance. FCI USA, Inc. Issued Date 12/20/2012 Manual P/N 10123594-9090 Page 4 of 9 SPECIFICATIONS Length mm Width mm Height mm Weight 240 grams lbs Color Black with Blue Handles CRIMP SPECIFICATIONS Refer to FCI application specification “TA-317” SAFETY PRECAUTIONS CAUTION Verify that the hand tool is free of any debris, such as wire strands and that it manually operates correctly. CAUTION This tool is designed to be operated by hand. Never install the HT-2234 hand tool in an air or pneumatic assisted device as damage to the tool and increased safety concerns will result. CAUTION It is suggested to wear lightweight gloves when handling hand tools and terminals. SETTING UP THE HAND TOOL: ATTACHING THE TOOL HEAD: Push on both attachment pins from the front to disengage the locking feature of the pins, as shown in Figure 1 above. Turn the tool around and manually pull out on each of the pin heads to fully retract the pins until each pin locks into the retracted position, as shown in Figure 2 above.

PDF Datasheet Preview

DUBOXTM LOOSE PIECE HAND TOOL

Hand Tool Part Number HT-2234 22 - 30 AWG

For termination Of DuboxTM 76357-x01LF Terminals

FCI MANUAL P/N 10123594-9090

FCI USA, Inc. Issued Date 12/20/2012

Manual P/N 10123594-9090 Page 1 of 9

FCI USA, Inc. Issued Date 12/20/2012

HT-2234 HAND TOOL

Table of Contents

HAND TOOL

TABLE OF CONTENTS

INTRODUCTION SCOPE OF HAND TOOL FEATURES SPECIFICATIONS CRIMP SAFETY

SETTING UP THE HAND TOOL ATTACHING THE TOOL HEAD

CRIMPING PROCEEDURES LOADING THE DUBOXTM TERMINAL 7 CRIMPING PROCESS 8

TERMINAL HOLDER ADJUSTMENT ALIGNMENT 9

ROUTINE MAINTENANCE

PARTS REPLACEMENT

REFERENCE DRAWINGS TA-317

REFERENCE DOCUMENTS FORM #E-3245 - -Customer Application Machine Warranty and Service Policy “Section I” Equipment owned by FCI USA LLC. FORM #E-3244 - -Customer Application Machine Warranty and Service Policy “Section II” Equipment purchased by the customer. FORM # E-3247- - FCI Electronics Address List

Data herein have been verified and validated and are believed adequate for the intended use of the applicator. If the applicator or procedures are used for purposes over and above the capabilities specified herein, confirmation of their validity and suitability should be obtained otherwise, FCI USA LLC does not guarantee results and assumes no obligation or liability. This publication is not a license to operate under, nor a recommendation to infringe upon, any process patents.

FCI USA, Inc. Issued Date 12/20/2012

Manual P/N 10123594-9090 Page 3 of 9

INTRODUCTION

SCOPE OF MANUAL:

This manual contains the information necessary to understand, install, operate and maintain the HT-2234 DuboxTM hand tools. This information is intended for the use by both the operator and service personnel. However, certain procedures within the manual should be performed by service personnel only. These procedures are identified by a warning instruction. Refer to the table of contents for a breakdown of each subject matter covered in each section.

WARNINGS, CAUTIONS, and NOTES within the text of this manual are used to emphasize important and critical instructions.

WARNING An operating procedure, practice, etc. which if not carefully followed, could result in personal injury, or affect the operator’s health.

CAUTION An operating procedure, practice, etc. which, if not strictly observed, could result in damage of equipment.

NOTE An operating procedure, condition, etc. which it is essential to highlight.

We recommend that the operators and service personnel responsible for maintenance of the FCI hand tools become thoroughly familiar with all aspects of the hand tool construction and operation. If operational or maintenance problems arise which are beyond the scope of this manual, contact your district service representative.

HAND TOOL FEATURES:

The HT-2234 Designed to terminate a single 22 30 awg pre-stripped discrete wire to a loose-piece 22 30 awg DuboxTM terminal, P/N 76357-x01LF. Two sets of crimp tooling are provided One set is used to terminate 22 24 awg wires while the other is utilized to terminate 26 - 30 awg wires. Labeling above each set of crimp tooling indicates the appropriate wire range for that location.

The HT-2234 hand tool used to ergonomically terminate 1 crimp per cycle without lengthy set-up times.
• A terminal holder is provided with two cavities that correspond to the conductor size being terminated.
• Ratcheting handle ensures the complete crimping process has been fully completed and can be released if required.
• Spring-loaded wire-stops are installed on each tooling cavity to assist with correct wire placement.
• The tool head can be easily separated from the handles for cleaning and tool maintenance.

FCI USA, Inc. Issued Date 12/20/2012

Manual P/N 10123594-9090 Page 4 of 9

SPECIFICATIONS Length mm Width mm Height mm Weight 240 grams lbs Color Black with Blue Handles

CRIMP SPECIFICATIONS Refer to FCI application specification “TA-317”

SAFETY PRECAUTIONS CAUTION Verify that the hand tool is free of any debris, such as wire strands and that it manually operates correctly. CAUTION This tool is designed to be operated by hand. Never install the HT-2234 hand tool in an air or pneumatic assisted device as damage to the tool and increased safety concerns will result. CAUTION It is suggested to wear lightweight gloves when handling hand tools and terminals.

SETTING UP THE HAND TOOL:

ATTACHING THE TOOL HEAD:

Push on both attachment pins from the front to disengage the locking feature of the pins, as shown in Figure 1 above. Turn the tool around and manually pull out on each of the pin heads to fully retract the pins until each pin locks into the retracted position, as shown in Figure 2 above.

More datasheets: R190-152-000 | R191-170-000 | R190-150-000 | R190-130-000 | R191-152-000 | R190-132-000 | R191-150-000 | R191-092-000 | R190-110-000 | R190-112-000

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HT-2234 Datasheet file may be downloaded here without warranties.

Datasheet ID: HT-2234 635123